xATSSwitchSettingsHighVoltageTransferPoint
PowerNet-MIB ·
.1.3.6.1.4.1.318.1.1.17.3.2.2
Object
scalar
mandatory
r/w
Integer32
The highest acceptable voltage condition at source 1. When any phase of source 1 is greater than this voltage, source quality is considered bad and the generator run signal is asserted to begin generator operation. Specified in volts, line-to-line for a 3-wire service or line-to-neutral for a 4-wire service. -1 if not available.
Context
- MIB
- PowerNet-MIB
- OID
.1.3.6.1.4.1.318.1.1.17.3.2.2- Type
- scalar
- Access
- readwrite
- Status
- mandatory
- Parent
- xATSSwitchSettings
- Siblings
- 9
Syntax
Integer32
- Source
- COPS-PR-SPPIInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| xATSSwitchSettingsLowVoltageTransferPoint mandatory The lowest acceptable voltage condition at source 1.
When any phase of source 1 is lower than this voltage,
source quality is considered bad and the generator run signal
is assert… | scalar | Integer32 | .1.3.6.1.4.1.318.1.1.17.3.2.1 |
| xATSSwitchSettingsSetToFactoryDefaults mandatory Sets all transfer switch settings to factory default values. | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.17.3.2.10 |
| xATSSwitchSettingsMaxFrequencyDeviation mandatory The maximum acceptable frequency deviation condition from nominal at source 1.
When source 1 frequency is outside the specified range,
source quality is considered bad and the gen… | scalar | Integer32 | .1.3.6.1.4.1.318.1.1.17.3.2.3 |
| xATSSwitchSettingsMinPhaseBalance mandatory The minimum required phase balance at source 1.
When the percentage difference between the minimum and maximum
phase voltage measurements at source 1 is greater than this value,
s… | scalar | Integer32 | .1.3.6.1.4.1.318.1.1.17.3.2.4 |
| xATSSwitchSettingsNominalRotation mandatory The nominal phase rotation (or phase sequence) required by the load.
For certain types of equipment, such as rotating machinery, phase rotation
is critical for proper operation as… | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.17.3.2.5 |
| xATSSwitchSettingsAllowClosedTransfer mandatory This setting enables seamless (closed) transfers between sources.
When possible, both source 1 and source 2 are closed to the output
for a brief time. If closed transfer is not po… | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.17.3.2.6 |
| xATSSwitchSettingsMaxSyncTime mandatory When attempting/seeking to perform a closed transfer, this setting defines
the maximum time allowed before the transfer switch will give up and perform
an open transfer. Specified… | scalar | Integer32 | .1.3.6.1.4.1.318.1.1.17.3.2.7 |
| xATSSwitchSettingsNeutralTransferTime mandatory This setting defines how long both source 1 and source 2 will be
disconnected from the output, during an open transfer.
Specified in seconds.
-1 if not available. | scalar | Integer32 | .1.3.6.1.4.1.318.1.1.17.3.2.8 |
| xATSSwitchSettingsClearLatchedAlarms mandatory Clears any latched alarm conditions. | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.17.3.2.9 |