upsAdvConfigDeepDischargeProtection

PowerNet-MIB · .1.3.6.1.4.1.318.1.1.1.5.2.56
MIB view Table view

Object

scalar mandatory r/w Enumeration 
Indicates whether protection against deep discharge is enabled or disabled.

Context

MIB
PowerNet-MIB
OID
.1.3.6.1.4.1.318.1.1.1.5.2.56
Type
scalar
Access
readwrite
Status
mandatory
Parent
upsAdvConfig
Siblings
79

Syntax

Enumeration

Values & Constraints

Enumerated Values
1enabled
2disabled

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
upsAdvConfigRatedOutputVoltage mandatory
The nominal output voltage from the UPS in VAC. For a list of allowed values supported by your UPS model, see the UPS User's Manual. If a value other than a …
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.1
upsAdvConfigShutoffDelay mandatory
The delay in seconds the UPS remains on after being told to turn off. For a list of allowed values supported by your UPS model, see the UPS User's Manual. If…
scalarRFC1155-SMITimeTicks.1.3.6.1.4.1.318.1.1.1.5.2.10
upsAdvConfigUpsSleepTime mandatory
The time in seconds for the UPS to go to 'sleep' when instructed. When in sleep mode, the UPS will not provide output power regardless of the input line state. Once the specifie…
scalarRFC1155-SMITimeTicks.1.3.6.1.4.1.318.1.1.1.5.2.11
upsAdvConfigSetEEPROMDefaults mandatory
WRITE: Resets the UPS EEPROM variables to default values. READ: returns 1
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.12
upsAdvConfigDipSwitchTable mandatory
Current settings of UPS dip switches.
table-.1.3.6.1.4.1.318.1.1.1.5.2.13
upsAdvConfigBattExhaustThresh mandatory
The number of seconds prior to battery exhaustion when the UPS will switch off power to its load.
scalarRFC1155-SMITimeTicks.1.3.6.1.4.1.318.1.1.1.5.2.14
upsAdvConfigPassword mandatory
The password entered at the UPS front panel to enable local configuration of the EEProm. If the password is disabled or is not supported, then the agent returns a null string.
scalarRFC1213-MIBDisplayString.1.3.6.1.4.1.318.1.1.1.5.2.15
upsAdvConfigAllowedSetTable mandatory
The table listing the allowed values for all discrete configurable UPS variables.
table-.1.3.6.1.4.1.318.1.1.1.5.2.16
upsAdvConfigBattCabAmpHour mandatory
Configure the amp-hour setting of the UPS battery solution. The value shows the maximum battery capacity configured for the UPS when using a third party battery solution regardles…
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.17
upsAdvConfigPositionSelector mandatory
Configure UPS position selector. If the UPS doesn't support this configuration it will report unknown (1). The positions are either rack (2) for rack mounted or tower (3) for tow…
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.18
upsAdvConfigOutputFreqRange mandatory
Configure the output frequency tolerance range. unknown(1) indicates the output frequency is unknown. freqRangeAUTO(2) configure the output frequency range for automatic. freqRang…
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.19
upsAdvConfigHighTransferVolt mandatory
The maximum line voltage in VAC allowed before the UPS system transfers to battery backup. For a list of allowed values supported by your UPS model, see the UPS User's …
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.2
upsAdvConfigUPSFail mandatory
Configure the UPS fail action. If UPS fails, and frequency or voltage is out of range it will either GotoBypass (2) or DropLoad (3). This OID will report unknown (1) if it is no…
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.20
upsAdvConfigAlarmRedundancy mandatory
Configure settings of UPS alarm if the redundancy is under the current redundancy. Use 0 for never.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.21
upsAdvConfigAlarmLoadOver mandatory
Configure settings of UPS alarm if the load is over the current load in kVA. Use -1 for never.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.22
upsAdvConfigAlarmRuntimeUnder mandatory
Configure settings of UPS alarm if the runtime is under the current time of minutes. Use -1 for never.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.23
upsAdvConfigVoutReporting mandatory
Configure the way the UPS scales its output voltage readings. unknown(1) indicates the Vout Reporting is unknown. voutAUTO(2) configure the Vout Reporting for automatic scaling. v…
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.24
upsAdvConfigNumExternalBatteries mandatory
Configure the number of external batteries connected to the UPS.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.25
upsAdvConfigSimpleSignalShutdowns mandatory
Configure Simple Signal shutdown commands from the Simple Signal port to be issued to the UPS. unknown(1) indicates the Simple Signal Shutdown setting is unknown. disabled(2) conf…
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.26
upsAdvConfigMaxShutdownTime mandatory
The maximum amount of time for server shutdown to complete before a UPS shutdown occurs.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.27
upsAsiUpsControlServerRequestShutdown mandatory
Start a server shutdown sequence: serverShutdownOff: Shutdown server and turn off UPS serverShutdownReboot: Shutdown server and turn reboot UPS.
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.28
upsAdvConfigMinReturnRuntime mandatory
The minimum amount of run time in seconds required before the output will be turned on, using power calculation captured at start of last shutdown.
scalarRFC1155-SMITimeTicks.1.3.6.1.4.1.318.1.1.1.5.2.29
upsAdvConfigLowTransferVolt mandatory
The minimum line voltage in VAC allowed before the UPS system transfers to battery backup. For a list of allowed values supported by your UPS model, see the UPS User's …
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.3
upsAdvConfigBasicSignalLowBatteryDuration mandatory
The duration of runtime in seconds during an on-battery condition at which the UPS will signal the basic low battery shutdown condition.
scalarRFC1155-SMITimeTicks.1.3.6.1.4.1.318.1.1.1.5.2.30
upsAdvConfigBypassPhaseLockRequired mandatory
Sets the condition for when bypass is an acceptable mode of operation as a requirement.
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.31
upsAdvConfigOutputFreqSlewRate mandatory
The rate at which the UPS will change its output frequency in response to utility frequency changes.
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.32
upsAdvConfigChargerLevel mandatory
Sets the rate at which the UPS charges its batteries.
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.33
upsAdvConfigBypassToleranceSetting mandatory
This setting allows selecting from standard bypass tolerance configurations to suit their situation.
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.34
upsAdvConfigMainsSetting mandatory
Configure the type of mains supply system. singleInput (1) indicates a single supply system. dualInput (2) indicates a dual supply system.
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.35
upsAdvConfigACWiringSetting mandatory
Configure the AC wiring of the system. threeWire (1) indicates 3-wire system configuration. fourWire (2) indicates 4-wire system configuration. fourWireHRG (3) indicates a 4-wire…
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.36
upsAdvConfigUpperOutputVoltTolerance mandatory
Upper tolerance of the output RMS voltage before transferring to bypass. Expressed as percent of nominal voltage.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.37
upsAdvConfigLowerOutputVoltTolerance mandatory
Lower tolerance of the output RMS voltage before transferring to bypass. Expressed as percent of nominal voltage.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.38
upsAdvConfigUpperBypassVoltTolerance mandatory
Upper tolerance of the bypass voltage that allows transfer to bypass by user. Expressed as percent of nominal voltage.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.39
upsAdvConfigAlarm mandatory
A flag indicating how the UPS should handle audible line fail alarms: timed(1): UPS alarm will sound after a preset timed duration starting from the line fail condition (see OID u…
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.4
upsAdvConfigLowerBypassVoltTolerance mandatory
Lower tolerance of the bypass voltage that allows transfer to bypass by user. Expressed as percent of nominal voltage.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.40
upsAdvConfigOutofSyncBypassTransferDelay mandatory
Configure the time (in milliseconds), indicating the gap in output voltage if an asynchronous transfer to bypass needs to occur.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.41
upsAdvConfigWarningAlarmDelay mandatory
Configure the time delay for reporting warning alarms (in seconds).
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.43
upsAdvConfigInformationalAlarmDelay mandatory
Configure the time delay for reporting informational alarms (in seconds).
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.44
upsAdvConfigGreenMode mandatory
Enable/Disable UPS green mode feature.
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.45
upsAdvConfigLCDLocalLanguage mandatory
Configure the language setting of the UPS LCD display information.
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.46
upsAdvConfigLCDLockOut mandatory
Enable/Disable the control function of the UPS via the LCD Display.
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.47
upsAdvConfigChargerRate mandatory
Change the maximum allowed UPS charge rate on select products where 100% represents the manufacturer's recommended rate. A charge/discharge rate of C/10 for a 10 Ah battery would…
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.48
upsAdvConfigBatterySelection mandatory
Configure the installed battery type; VRLA is a Valve Regulated Lead Acid type battery, Vented Cell is a wet cell type (car) battery, NiCd is a Nickel-Cadmium type battery, and Li…
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.49
upsAdvConfigAlarmTimer mandatory
The time after initial line failure at which the UPS begins emitting audible alarms (beeping). This timer is observed only if the value of extControlAlarm is timed(2). Allowed va…
scalarRFC1155-SMITimeTicks.1.3.6.1.4.1.318.1.1.1.5.2.5
upsAdvConfigBatteryHealthAlarmWarningTime mandatory
Configure the number of days before the battery health is depleted that the battery health alarm is activated. Setting this to -1, if supported by the UPS, will suppress the batte…
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.50
upsAdvConfigBatteryHealthAlarmSleepTime mandatory
Configure the number of days that the UPS device's battery health alarm should sleep before being activated again after being acknowledged. Setting this to -1, if supported by the…
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.51
upsAdvConfigSignalFlashVoltage mandatory
Configure the signal flash voltage in tenths of volts.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.52
upsAdvConfigBatteryTemperatureCompensation mandatory
Configure the battery temperature compensation voltage in hundreds of volts per degree C. On products which support this field, the charger voltage is reduced for each degree C ri…
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.53
upsAdvConfigBatteryChargerType mandatory
This OID describes type of battery charger used: standard or extended. 1 - Internal charger, 2 - Extended (CLA), 3 - Large extension (other cases), 4 - Extra large extension (XL),…
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.54
upsAdvConfigAutomaticRestart mandatory
Indicates whether Automatic Restart is enabled or disabled.
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.55
upsAdvConfigFreqBypassTransferRange mandatory
Tolerance of bypass AC frequency to switch on bypass. The frequency must be in range of -X% to +X% around the nominal value.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.57
upsAdvConfigUpsPowerconverterType mandatory
This value indicates the type of UPS in terms of output phase and redundancy. 2 - Galaxy 7000 Unitary 3:3 3 - Galaxy 7000 Redundant 3:3 4 - Galaxy 7000 Parallel SSC 3:3 6 - Ga…
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.58
upsAdvConfigFrequencyConverterMode mandatory
Indicates whether the output frequency is in Auto Ranging or Frequency converter mode. In Auto Ranging mode the inverter provides output frequency in the same range as the input. …
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.59
upsAdvConfigMinReturnCapacity mandatory
The minimum battery capacity required before the UPS will return from a low battery shutdown condition. The capacity is measured from 0% battery capacity (or Low Battery) as a pe…
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.6
upsAdvConfigACQualificationTime mandatory
The time in seconds that the voltage is required to be in the acceptable range before being declared to be acceptable.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.60
upsAdvConfigRebootDuration mandatory
During a reboot sequence, power is turned off and then back on. This OID defines the minimum amount of time to wait (seconds) after turning the power off, at the start of the sequ…
scalarRFC1155-SMITimeTicks.1.3.6.1.4.1.318.1.1.1.5.2.61
upsAdvConfigAutoShutdownControlSkipOffDelay mandatory
Configures whether the UPS device's off delay setting (upsAdvConfigShutoffDelay) will be used for automatic shutdown.
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.62
upsAdvConfigAutoShutdownControlAutoRestart mandatory
Configures whether the UPS will automatically restart after an automatic shutdown.
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.63
upsAdvConfigAutoShutdownControlTimeOnBattery mandatory
Configures whether the UPS will turn off automatically after the UPS device's time on battery has exceeded the upsAdvConfigAutoShutdownTimeOnBattery OID setting.
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.64
upsAdvConfigAutoShutdownControlRuntimeRemaining mandatory
Configures whether the UPS will turn off when the UPS is on battery and the remaining runtime is less than the upsAdvConfigAutoShutdownRuntimeRemaining OID setting.
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.65
upsAdvConfigAutoShutdownTimeOnBattery mandatory
When the UPS has been on battery for more time than this value, the UPS will turn off if this condition is enabled by the upsAdvConfigAutoShutdownControlTimeOnBattery OID.
scalarRFC1155-SMITimeTicks.1.3.6.1.4.1.318.1.1.1.5.2.66
upsAdvConfigAutoShutdownRuntimeRemaining mandatory
When the UPS runtime remaining is less than this setting, the UPS will turn off if this condition is enabled by the upsAdvConfigAutoShutdownControlRuntimeRemaining OID.
scalarRFC1155-SMITimeTicks.1.3.6.1.4.1.318.1.1.1.5.2.67
upsAdvConfigHighLLTransferVolt mandatory
The maximum line to line voltage in VAC allowed before the UPS system transfers to battery backup. For a list of allowed values supported by your UPS model, see the UPS…
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.68
upsAdvConfigLowLLTransferVolt mandatory
The minimum line to line voltage in VAC allowed before the UPS system transfers to battery backup. For a list of allowed values supported by your UPS model, see the UPS…
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.69
upsAdvConfigSensitivity mandatory
The sensitivity of the UPS to utility line abnormalities or noises.
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.7
upsAdvConfigHighBypassTransferVolt mandatory
The maximum line voltage, in VAC, that the UPS system will allow a transfer to bypass.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.70
upsAdvConfigLowBypassTransferVolt mandatory
The minimum line voltage, in VAC, that the UPS system will allow a transfer to bypass.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.71
upsAdvConfigHighBypassLLTransferVolt mandatory
The maximum line to line voltage, in VAC, that the UPS system will allow a transfer to bypass.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.72
upsAdvConfigLowBypassLLTransferVolt mandatory
The minimum line to line voltage, in VAC, that the UPS system will allow a transfer to bypass.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.73
upsAdvConfigAutoShutdownControlBatteryCapacity mandatory
This setting only shuts down the UPS when the UPS is on battery and when the battery capacity is less than the upsAdvConfigAutoShutdownBatteryCapacity OID setting.
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.74
upsAdvConfigAutoShutdownBatteryCapacity mandatory
When the Battery capacity is less than this value, the UPS will turn off, if this condition is enabled by upsAdvConfigAutoShutdownControlBatteryCapacity OID setting.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.75
upsAdvConfigAutoShutdownControlLoadPercentOnUps mandatory
This setting only shuts down the UPS when the UPS is on battery and when the load percent on UPS is less than the upsAdvConfigAutoShutdownLoadPercentOnUps OID setting.
scalarEnumeration.1.3.6.1.4.1.318.1.1.1.5.2.76
upsAdvConfigAutoShutdownLoadPercentOnUps mandatory
When the Load percent on UPS is less than this value, the UPS will turn off, if this condition is enabled by the upsAdvConfigAutoShutdownControlLoadPercentOnUps OID setting.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.77
upsAdvConfigBypassFrequencyRangeLowerLimit mandatory
Lower Limit of Bypass Frequency Range in Hz.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.78
upsAdvConfigBypassFrequencyRangeUpperLimit mandatory
Upper Limit of Bypass Frequency Range in Hz.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.79
upsAdvConfigLowBatteryRunTime mandatory
The desired run time of the UPS, in seconds, once the low battery condition is reached. During this time the UPS may produce a constant warning tone, which cannot be disabled, dep…
scalarRFC1155-SMITimeTicks.1.3.6.1.4.1.318.1.1.1.5.2.8
upsAdvConfigEcoVoltageRangeLowerLimit mandatory
Lower Limit of ECO Voltage Range in Volts.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.80
upsAdvConfigEcoVoltageRangeUpperLimit mandatory
Upper Limit of ECO Voltage Range in Volts.
scalarInteger32.1.3.6.1.4.1.318.1.1.1.5.2.81
upsAdvConfigReturnDelay mandatory
The delay in seconds after utility line power returns before the UPS will turn on. This value is also used when the UPS comes out of a reboot and before the UPS wakes up from 'sl…
scalarRFC1155-SMITimeTicks.1.3.6.1.4.1.318.1.1.1.5.2.9