airIRRP500UnitConfigHumidifierControl
PowerNet-MIB ·
.1.3.6.1.4.1.318.1.1.13.3.3.2.2.6.8
Object
scalar
mandatory
r/w
Enumeration
The humidifier drain control.
Context
- MIB
- PowerNet-MIB
- OID
.1.3.6.1.4.1.318.1.1.13.3.3.2.2.6.8- Type
- scalar
- Access
- readwrite
- Status
- mandatory
- Parent
- airIRRP500UnitConfig
- Siblings
- 14
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | auto |
2 | drainOff |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| airIRRP500UnitConfigStartupDelay mandatory The startup delay in seconds. | scalar | Integer32 | .1.3.6.1.4.1.318.1.1.13.3.3.2.2.6.1 |
| airIRRP500UnitConfigReheatEnable mandatory Enable/disable reheat. | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.13.3.3.2.2.6.10 |
| airIRRP500UnitConfigHeatAssistEnable mandatory Enable/disable heat assist. | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.13.3.3.2.2.6.11 |
| airIRRP500UnitConfigPowerSourceConfig mandatory Configure the input power source: (1) single feed or (2) dual feed. | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.13.3.3.2.2.6.12 |
| airIRRP500UnitConfigUnitRoleOverride mandatory When this OID value is (1) automatic, the system determines
which units are used as primary units and which units are used as backups.
When this OID value is (2) forcedOn, the con… | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.13.3.3.2.2.6.13 |
| airIRRP500UnitConfigSecondaryPowerFeedCapability mandatory Available on chilled water units. When the power source config setting
is set to dual, setting this value to reduced (2) will inhibit the heater
and humdifier when the unit is be… | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.13.3.3.2.2.6.14 |
| airIRRP500UnitConfigIdleOnCoolFail mandatory When this OID value is (1) enable, the unit idles if it detects that it is blowing warm
air into the cold aisle. The unit will attempt to restart at 5 minute intervals. | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.13.3.3.2.2.6.15 |
| airIRRP500UnitConfigCoolCapacity mandatory The cooling capacity options setting. | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.13.3.3.2.2.6.2 |
| airIRRP500UnitConfigIdleOnLeakDetect mandatory The idle on leak options setting. | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.13.3.3.2.2.6.3 |
| airIRRP500UnitConfigInputNormalState mandatory The normal state of the input contact. | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.13.3.3.2.2.6.4 |
| airIRRP500UnitConfigOutputNormalState mandatory The normal state of the output relay. | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.13.3.3.2.2.6.5 |
| airIRRP500UnitConfigOutputSource mandatory The source of output relay change. | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.13.3.3.2.2.6.6 |
| airIRRP500UnitConfigHumidifyEnable mandatory Enable/disable humidification. | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.13.3.3.2.2.6.7 |
| airIRRP500UnitConfigDehumidifyEnable mandatory Enable/disable dehumidification. | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.13.3.3.2.2.6.9 |