wirelessIfOperationalMode
PROXIM-MIB ·
.1.3.6.1.4.1.841.1.1.1.1.1.1.1.3
Object
column
r/w
OctetString
This parameter is used to set the wireless NIC Operational mode.
Depending on the wireless NIC in the device different wireless
operational modes can be configured. The object wirelessIfSupportedOperationalMode
shows the supported modes and the possible supported modes for
AP products:
dot11b(1),
dot11g(2),
dot11ng(3),
dot11a(4),
dot11na(5)
Context
- MIB
- PROXIM-MIB
- OID
.1.3.6.1.4.1.841.1.1.1.1.1.1.1.3- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- wirelessIfPropertiesTableEntry
- Table
- wirelessIfPropertiesTable
- Siblings
- 24
Syntax
OctetString
Values & Constraints
Enumerated Values
1 | enable |
2 | disable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| wirelessIfPropertiesTableIndex This parameter represents a unique value for each Wireless interface
in the system and is used as index to this table. | column | Unsigned32 | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.1 |
| wirelessIfAutoRateSelection This parameter is used to configure the value for Auto Rate Selection for the
wireless interface. Select
(1) to enable the Auto Rate selection and
(2) to disable the Auto Rate… | column | Enumeration | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.10 |
| wirelessIfTransmittedRate This parameter represents the number of rates transmitted for wireless. | column | Unsigned32 | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.11 |
| wirelessIfSupportedRate This parameter represents the number of rates supported for wireless. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.12 |
| wirelessIfVAPRTSThreshold This parameter represents the maximum threshold for VAP RTS (Request To Send).
The maximum threshold can be configured up to 2346. | column | Unsigned32 | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.13 |
| wirelessIfVAPBeaconInterval This parameter represents the time interval that a beacon takes for getting
transmitted for wireless VAP. By default, the value is set to 100 ms. | column | Unsigned32 | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.14 |
| wirelessIfTPC This parameter represents the cell size that the transmitted power controls. It is
measured in dBm. Please check the wirelessIfActiveTPC for current active TPC. | column | Unsigned32 | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.15 |
| wirelessIfCellSize This parameter represents the cell size of the wireless. By default, the cell size
is configured to large. Select
(1) for Small cell size,
(2) for Medium cell size and
(3) for L… | column | Enumeration | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.16 |
| wirelessIfDTIM This parameter represents the delivery traffic indication map
period. This is the interval between the transmission of multicast
frames on the wireless inteface. It is expres… | column | Unsigned32 | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.17 |
| wirelessIfAntennaGain This parameter is used to configure the antenna gain. | column | Unsigned32 | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.18 |
| wirelessIfCurrentActiveChannel This parameter represents the current active channel that wireless radio is
operating on. It may be different from the configured channel represented by
wirelessIfCurrentOperatin… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.19 |
| wirelessIfPropertiesRadioStatus This parameter is used to provide the status of the Wireless Radio
interface. Select
(1) to enable the wireless interface and
(2) to disable the wireless interface. | column | Enumeration | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.2 |
| wirelessIfSatelliteDensity This parameter represents the density of the satellites for the BSU.
It configures the BSU to accomodate the satellites for the specified
range. | column | Enumeration | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.20 |
| wirelessIfMPOperationalMode This parameter is used to set the wireless NIC Operational mode for Tsunami Multi
Point Products. | column | Enumeration | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.21 |
| wirelessIfChannelWaitTime This parameter is used to configure the DFS channel wait time. | column | Unsigned32 | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.22 |
| wirelessIfActiveTPC This parameter shows the active cell size that the transmitted power controls. It is
measured in dBm | column | Unsigned32 | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.23 |
| wirelessIfDfsNumSatWithRadarForFreqSwitch This parameter represents the minimum number of satellites reporting RADAR for BSU to
switch to a new best channel/frequency. The default value is (0) that indicates BSU to never… | column | Unsigned32 | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.24 |
| wirelessIfDfsStatus This parameter is used to configure the status of the DFS for SU. Configuring this parameter
for BSU will not affecte BSU Status.
1 to enable the DFS,
2 to disable the DFS. | column | Enumeration | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.25 |
| wirelessIfSupportedOperationalMode This parameter is used to set the wireless supported Operational mode. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.4 |
| wirelessIfCurrentChannelBandwidth This parameter represents the current bandwidth that Wireless is
currently operating on. It is represented in MHz | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.5 |
| wirelessIfSupportedChannelBandwidth This parameter represents the channel bandwidths that a wireless can support. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.6 |
| wirelessIfAutoChannelSelection This parameter is used to configure the auto channel selection for wireless
interface. Select
(1) to enable the auto channel selection and
(2) to disable the auto channel selec… | column | Enumeration | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.7 |
| wirelessIfCurrentOperatingChannel This parameter represents the user configured channel that the radio is
configured to operate in.
Note: It is possible that the currently active channel is different.
To … | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.8 |
| wirelessIfSupportedChannels This parameter represents the channels that wireless can support. | column | OctetString | .1.3.6.1.4.1.841.1.1.1.1.1.1.1.9 |