portHdwEchoSuppression
PERLE-IOLAN-SDS-MIB ·
.1.3.6.1.4.1.1966.12.1.5.2.1.13
Object
column
r/w
OnOffValue
This parameter applies only to EIA-485 Half Duplex mode. All characters will be echoed to the user and transmitted across the serial ports. Some EIA-485 applications require local echo to be enabled in order to monitor the loopback data to determine that line contention has occurred. If your application cannot handle loopback data, echo suppression should be On. The default is echo suppression Off.
Context
- MIB
- PERLE-IOLAN-SDS-MIB
- OID
.1.3.6.1.4.1.1966.12.1.5.2.1.13- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- portHdwEntry
- Table
- portHdwTable
- Siblings
- 32
Syntax
OnOffValue
- Source
- OnOffValue
- Base type
Enumeration
Values & Constraints
Type Values
1 | off |
2 | on |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| portHdwIndex Port hardware Index | column | PortNumber | .1.3.6.1.4.1.1966.12.1.5.2.1.1 |
| portHdwMonitorDCD Specifies whether the RS-232 signal DCD (Data Carrier Detect) should
be monitored. This object does not apply to DCE serial interfaces.
This is used with modems or… | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.5.2.1.10 |
| portHdwDuplex Specify whether the line is Full Duplex (communication both ways
at the same time) or Half Duplex (communication in one direction
at a time). | column | Enumeration | .1.3.6.1.4.1.1966.12.1.5.2.1.11 |
| portHdwTXDriverControl Used with a EIA-485 serial interface, if your application supports
RTS (Request To Send), select this option. Otherwise, select Auto.
Default is Auto | column | Enumeration | .1.3.6.1.4.1.1966.12.1.5.2.1.12 |
| portHdwUART portHdwUART | column | Enumeration | .1.3.6.1.4.1.1966.12.1.5.2.1.14 |
| portHdwIRQ Port Hardware IRQ | column | Integer32 | .1.3.6.1.4.1.1966.12.1.5.2.1.15 |
| portHdwTxBytes portHdwTxBytes | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1966.12.1.5.2.1.16 |
| portHdwRxBytes portHdwRxBytes | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1966.12.1.5.2.1.17 |
| portHdwFrameErrs portHdwFrameErrs | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1966.12.1.5.2.1.18 |
| portHdwParityErrs portHdwParityErrs | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1966.12.1.5.2.1.19 |
| portHdwStatus When you perform a GET on this variable, one of
the following values will be returned:
1-Indicates that the container folder is active with no changes.
2-Indicates that the contai… | column | ContainerStatus | .1.3.6.1.4.1.1966.12.1.5.2.1.2 |
| portHdwBreaks portHdwBreaks | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1966.12.1.5.2.1.20 |
| portHdwOverruns portHdwOverruns | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1966.12.1.5.2.1.21 |
| portHdwRTS portHdwRTS | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.5.2.1.22 |
| portHdwCTS portHdwCTS | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.5.2.1.23 |
| portHdwDTR portHdwDTR | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.5.2.1.24 |
| portHdwDSR portHdwDSR | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.5.2.1.25 |
| portHdwCD portHdwCD | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.5.2.1.26 |
| portHdwRI portHdwRI | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.5.2.1.27 |
| portSoftTermination Enables or disables software line termination. | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.5.2.1.29 |
| portHdwInterface Specifies the type of line that is being used with the
Device Server. Select either EIA-232, EIA-422, or EIA-485. | column | Enumeration | .1.3.6.1.4.1.1966.12.1.5.2.1.3 |
| portHdwCustomSpeed The custom baud rate for this port. | column | Integer32 | .1.3.6.1.4.1.1966.12.1.5.2.1.30 |
| portHdwDiscardCharactersRecievedWithErrors This option if set will discard any characters recieved on the
uart that have overrun, framing or parity errors. If not set,
then the characters are sent out the network connect… | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.5.2.1.31 |
| portHdwRtsToggle This option if set will toggle RTS on before transmitting the
first character and toggle RTS off after transmitting the
last character. | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.5.2.1.32 |
| portHdwRtsInitialDelay The delay, in msec, between turning RTS on and transmittng
the first character. | column | Integer32 | .1.3.6.1.4.1.1966.12.1.5.2.1.33 |
| portHdwRtsFinalDelay The delay, in msec, between transmitting the last character
and turning RTS off. | column | Integer32 | .1.3.6.1.4.1.1966.12.1.5.2.1.34 |
| portHdwSpeed Specifies the baud rate of the line; keep in mind that
speed is affected by the length of the cable. When bCustom
is set, then the baud rate is specified by portHwdCustomSpeed.
I… | column | Enumeration | .1.3.6.1.4.1.1966.12.1.5.2.1.4 |
| portHdwDataBits Specifies the number of bits in a byte. The default is 8.
Internal modems only support 7 and 8 data bits. | column | Enumeration | .1.3.6.1.4.1.1966.12.1.5.2.1.5 |
| portHdwParity Specifies if you are using Even, Odd, or No parity on the line.
If you want to force a parity type, you can specify Mark for 1
or Space for 0. | column | Enumeration | .1.3.6.1.4.1.1966.12.1.5.2.1.6 |
| portHdwStopBits Specifies the number of stop bits that follow a byte.
Certain models do not support 1.5 stop bits. Internal
modems only support 1 stop bit. | column | Enumeration | .1.3.6.1.4.1.1966.12.1.5.2.1.7 |
| portHdwFlowControl Defines whether the data flow is handled by the
software (Soft), hardware (Hard), Both, or None. | column | Enumeration | .1.3.6.1.4.1.1966.12.1.5.2.1.8 |
| portHdwMonitorDSR Specifies whether the RS-232 signal DSR (Data Set Ready) should
be monitored, for Device Servers with a DTE serial interface.
On a Device Server with a DCE serial interface, this … | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.5.2.1.9 |