defUserCallBack
PERLE-IOLAN-SDS-MIB ·
.1.3.6.1.4.1.1966.12.1.16.7
Object
scalar
r/w
OnOffValue
When On, enter a phone number for the Device Server to call the user back (the Callback parameter is unrelated to the Line Dial parameter). Note: the Device Server will allow callback only when a user is authenticated. If the protocol over the link does not provide authentication, there will be no callback. Therefore, when the Line Service is set to PPP, you must use either PAP or CHAP, because these protocols provide authentication. The default is Off. The Device Server supports another type of callback, Roaming Callback, which is configurable when the Line Service is set to PPP.
Context
- MIB
- PERLE-IOLAN-SDS-MIB
- OID
.1.3.6.1.4.1.1966.12.1.16.7- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- defUserInfo
- Siblings
- 21
Syntax
OnOffValue
- Source
- OnOffValue
- Base type
Enumeration
Values & Constraints
Type Values
1 | off |
2 | on |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| defUserStatus When you perform a GET on this variable, one of
the following values will be returned:
1-Indicates that the container folder is active with no changes.
2-Indicates that the contai… | scalar | ContainerStatus | .1.3.6.1.4.1.1966.12.1.16.1 |
| defUserIpHost When the User Service is set to Telnet, TCP_clear or SSL_RAW, the target
host IP address. If 255.255.255.255 is specified in the configuration,
the user will be prompted for an IP… | scalar | Ipv4v6Address | .1.3.6.1.4.1.1966.12.1.16.10 |
| defUserTelnetPort The port number the target host is listening on for
incoming connections. Default is 23. | scalar | Integer32 | .1.3.6.1.4.1.1966.12.1.16.11 |
| defUserSSHPort userSSHPort | scalar | Integer32 | .1.3.6.1.4.1.1966.12.1.16.12 |
| defUserTcpClearPort The port number for the TCP-Clear or SSL-Raw session. | scalar | Integer32 | .1.3.6.1.4.1.1966.12.1.16.13 |
| defUserFramedIp Used for User Service PPP or SLIP, sets the IP address of the
remote user. Enter the address in dot decimal notation as follows:
255.255.255.254 (default)-The Device Server will u… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.1966.12.1.16.14 |
| defUserSubnetBits (IPv4 only) If the remote user is on a subnet, enter the number of
bits in the subnet mask. For example, a subnet mask of 255.255.0.0
has 16 subnet/prefix bits. | scalar | Integer32 | .1.3.6.1.4.1.1966.12.1.16.15 |
| defUserIpv6InterfaceId Used for User Service PPP, sets the IP address of the remote user.
Enter the address in IPv6 format. The first 64 bits of the Interface
Identifier must be zero, therefore, ::abcd:… | scalar | Ipv6InterfaceId | .1.3.6.1.4.1.1966.12.1.16.16 |
| defUserFramedMtu Used for User Service PPP or SLIP, specifies the maximum size of
packets, in bytes, being transferred across the link. On noisy
links it might be preferable to fragment large pack… | scalar | Integer32 | .1.3.6.1.4.1.1966.12.1.16.17 |
| defUserFramedCompression Used for User Service PPP or SLIP, determines whether Van Jacobsen
Compression is used on the link. VJ compression is a means of reducing
the standard TCP/IP header from 40 octets… | scalar | OnOffValue | .1.3.6.1.4.1.1966.12.1.16.18 |
| defUserRouting Determines the routing mode used for RIP packets on the PPP and SLIP
interfaces. Values are:
None-RIP packets are neither received nor sent by the Device Server.
Send-RIP packets … | scalar | Enumeration | .1.3.6.1.4.1.1966.12.1.16.19 |
| defUserService The type of service that the user will use:
dsprompt, telnet, ssh, rlogin, slip, ppp, tcpclear
or sslraw. | scalar | Enumeration | .1.3.6.1.4.1.1966.12.1.16.2 |
| defUserAllowAccessClusterPorts Allow/disallow the user to access to clustering ports. | scalar | OnOffValue | .1.3.6.1.4.1.1966.12.1.16.20 |
| defUserHost The name of the host. | scalar | OctetString | .1.3.6.1.4.1.1966.12.1.16.21 |
| defUserPortAccessTable The port access info table for user. | table | - | .1.3.6.1.4.1.1966.12.1.16.22 |
| defUserLanguage You can specify whether a user will use English or
Customlang as the language that appears in the Menu,
CLI, or WebManager. The Device Server supports one custom
language that mus… | scalar | Enumeration | .1.3.6.1.4.1.1966.12.1.16.3 |
| defUserLevel The access that a user is allowed:
Admin-The admin level user has total access to the Device Server.
You can create more than one admin user account but we
recommend t… | scalar | Enumeration | .1.3.6.1.4.1.1966.12.1.16.4 |
| defUserHotKeyPrefix The prefix that a user types to control the current session. The default
value is hex 01, which corresponds to Ctrl-a (^a) (hex value 02 would
be Ctrl-b (^b), etc.):
^a number-To … | scalar | Hex8 | .1.3.6.1.4.1.1966.12.1.16.5 |
| defUserPhoneNumber The phone number the Device Server will dial to callback the user
(you must have set Callback to On). Enter the number without spaces. | scalar | OctetString | .1.3.6.1.4.1.1966.12.1.16.6 |
| defUserIdleTimer The amount of time, in seconds, that the Idle Timer will run. Use this timer
to close a connection because of inactivity. When the Idle Timer expires, because
there has been no ex… | scalar | Integer32 | .1.3.6.1.4.1.1966.12.1.16.8 |
| defUserSessionTimer Enter a time, in seconds, for which the Session Timer will run. Use this
timer to forcibly close the session (connection). When the Session Timer
expires, the Device Server will e… | scalar | Integer32 | .1.3.6.1.4.1.1966.12.1.16.9 |