oriWirelessIfQoSStatus
ORiNOCO-MIB ·
.1.3.6.1.4.1.11898.2.1.2.1.1.1.38
Object
column
r/w
ObjStatus
This object is used to enable/disable Quality of Service (QoS) on the wireless interface.
Context
- MIB
- ORiNOCO-MIB
- OID
.1.3.6.1.4.1.11898.2.1.2.1.1.1.38- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- oriWirelessIfPropertiesEntry
- Table
- oriWirelessIfPropertiesTable
- Siblings
- 39
Syntax
ObjStatus
- Source
- ObjStatus
- Base type
Enumeration
Values & Constraints
Type Values
1 | enable |
2 | disable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| oriWirelessIfPropertiesIndex This object represents a unique value for each interface in the
system and is used as index to this table. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11898.2.1.2.1.1.1.1 |
| oriWirelessIfAllowedSupportedDataRates This object reflects the transmit rates supported by the
wireless interface. The values of this object are given in
units of 500 kbps.
Examples for supported data rates:
- 80… | column | OctetString | .1.3.6.1.4.1.11898.2.1.2.1.1.1.10 |
| oriWirelessIfRegulatoryDomainList This object specifies a single regulatory domain (not a list) which
is supported by the wireless interface. | column | OctetString | .1.3.6.1.4.1.11898.2.1.2.1.1.1.11 |
| oriWirelessIfAllowedChannels This object reflects the radio frequency channels that the
interface supports. | column | OctetString | .1.3.6.1.4.1.11898.2.1.2.1.1.1.12 |
| oriWirelessIfMACAddress deprecated This object represents the MAC address of the wireless interface
present in the device. This object has been deprecated. | column | SNMPv2-TCPhysAddress | .1.3.6.1.4.1.11898.2.1.2.1.1.1.13 |
| oriWirelessIfLoadBalancing This object is used to configure the load balancing feature
for the wireless interface. | column | Enumeration | .1.3.6.1.4.1.11898.2.1.2.1.1.1.14 |
| oriWirelessIfMediumDensityDistribution This object is used to configure the medium density distribution
feature for the wireless interface. | column | Enumeration | .1.3.6.1.4.1.11898.2.1.2.1.1.1.15 |
| oriWirelessIfTxRate This object is used to configure the transmit rate for unicast
traffic for the wireless interface. This object is dependent on
the transmit rates supported by the wireless inte… | column | Integer32 | .1.3.6.1.4.1.11898.2.1.2.1.1.1.16 |
| oriWirelessIfAutoChannelSelectStatus This object is used to configure the automatic frequency channel
feature for the wireless interface. If this object is enabled, the
frequency channel object can not be set, but t… | column | Enumeration | .1.3.6.1.4.1.11898.2.1.2.1.1.1.17 |
| oriWirelessIfBandwidthLimitIn This object represents the input bandwidth limit of the interface
in increments of 64 kbps. The value can be limited by a previous
written value, the negotiation process during … | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.11898.2.1.2.1.1.1.18 |
| oriWirelessIfBandwidthLimitOut This object represents the output bandwidth limit of the interface
in increments of 64 kbps. The value can be limited by a previous
written value, the negotiation process during… | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.11898.2.1.2.1.1.1.19 |
| oriWirelessIfNetworkName This object represents the network name (SSID) for this wireless
interface. | column | OctetString | .1.3.6.1.4.1.11898.2.1.2.1.1.1.2 |
| oriWirelessIfTurboModeStatus This object is used to enable or disable turbo mode support. Turbo
mode is only supported for 802.11a PHY (OFDM - 5 GHz) and 802.11g
(ERP - 2.4 GHz) wireless NICs and can only be… | column | ObjStatus | .1.3.6.1.4.1.11898.2.1.2.1.1.1.20 |
| oriWirelessIfSupportedOperationalModes This object provides information on the wireless operational modes
supported by the NIC. Depending on the wireless NIC in the device
different wireless operational modes can be… | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.11898.2.1.2.1.1.1.21 |
| oriWirelessIfOperationalMode This object is used to set the wireless NIC Operational mode.
Depending on the wireless NIC in the device different wireless
operational modes can be configured. The supported mo… | column | Enumeration | .1.3.6.1.4.1.11898.2.1.2.1.1.1.22 |
| oriWirelessIfPreambleType This object identifies the wireless interface preamble type
based on the wireless operational mode configured. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.11898.2.1.2.1.1.1.23 |
| oriWirelessIfProtectionMechanismStatus This object indicates if protection mechanism is enabled or not
based on the wireless operational mode configured. | column | ObjStatus | .1.3.6.1.4.1.11898.2.1.2.1.1.1.24 |
| oriWirelessIfSupportedMulticastRates This object represents the multicast rates supported by the wireless
NIC and the operational mode configured. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.11898.2.1.2.1.1.1.25 |
| oriWirelessIfCapabilities This object provides information on the wireless capabilities and
features supported by the wireless NIC. Each bit in this object
defines a capability/feature supported by the w… | column | OctetString | .1.3.6.1.4.1.11898.2.1.2.1.1.1.26 |
| oriWirelessIfLBTxTimeThreshold Maximum allowed Tx processing time, in mS, where Tx processing time
is measured from time a packet enters AP from the DS to the time it
successfully leaves the AP's Radio. | column | Integer32 | .1.3.6.1.4.1.11898.2.1.2.1.1.1.27 |
| oriWirelessIfLBAdjAPTimeDiffThreshold Maximum allowed difference in mS between adjacent AP's Tx processing
time. | column | Integer32 | .1.3.6.1.4.1.11898.2.1.2.1.1.1.28 |
| oriWirelessIfACSFrequencyBandScan This object is used to configure the frequency bands that the auto
channel select algorithm will scan through. Each bit in this object
represents a band or subset of channels in … | column | Integer32 | .1.3.6.1.4.1.11898.2.1.2.1.1.1.29 |
| oriWirelessIfMediumReservation This object represents the medium reservation value. The range
for this parameter is 0 - 2347. The medium reservation specifies
the number of octects in a frame above which a R… | column | Integer32 | .1.3.6.1.4.1.11898.2.1.2.1.1.1.3 |
| oriWirelessIfSecurityPerSSIDStatus This object is used to enable or disable the security per SSID
feature. Once this object is enabled, the administrator should use
the Wireless Interface SSID table (oriWirelessIf… | column | ObjStatus | .1.3.6.1.4.1.11898.2.1.2.1.1.1.30 |
| oriWirelessIfDFSStatus This object is used to enable/disable dynamic frequency selection.
This functionality is dependent on the regulatory domain of the
wireless NIC. | column | ObjStatus | .1.3.6.1.4.1.11898.2.1.2.1.1.1.31 |
| oriWirelessIfAntenna deprecated This object is used to configure the antenna. The administrator can
select controllable, external, internal, or disable the antenna. | column | Enumeration | .1.3.6.1.4.1.11898.2.1.2.1.1.1.32 |
| oriWirelessIfTPCMode This object is used to configure the transmit power control of
the wireless NIC. The transmit power is defined in dBm and can be
configured in increments 3 dBms. | column | Integer32 | .1.3.6.1.4.1.11898.2.1.2.1.1.1.33 |
| oriWirelessIfSuperModeStatus This object is used to enable/disable super mode support. Super Mode
increases the overall throughput of the wireless interface by
implementing fast frame, bursting, and compress… | column | ObjStatus | .1.3.6.1.4.1.11898.2.1.2.1.1.1.34 |
| oriWirelessIfWSSStatus This object is used for the Wireless System Shutdown feature. This
feature allows an administrator to shut down wireless services to
clients. When this object is set to down wi… | column | Enumeration | .1.3.6.1.4.1.11898.2.1.2.1.1.1.35 |
| oriWirelessIfSupportedAuthenticationModes This object is used to provide information on the authentication modes
supported by the wireless interface. The possible authentication modes
are:
- none: no authenti… | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.11898.2.1.2.1.1.1.36 |
| oriWirelessIfSupportedCipherModes This object is used to provide information on the cipher modes/types
supported by the wireless interface. The possible cipher modes/types
are:
- none: no cipher/encry… | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.11898.2.1.2.1.1.1.37 |
| oriWirelessIfQoSMaxMediumThreshold This object is used to specify the QoS admission control maximum
medium threshold. The maximum medium threshold will apply to all
access categories and is given in a percentage … | column | Integer32 | .1.3.6.1.4.1.11898.2.1.2.1.1.1.39 |
| oriWirelessIfInterferenceRobustness This object enables or disables the interference robustness
feature. The default value for this object should be disable. | column | Enumeration | .1.3.6.1.4.1.11898.2.1.2.1.1.1.4 |
| oriWirelessIfAntennaGain This object represents Antenna Gain value (including cable loss) that will be
added to the radar detetection parameters. | column | Integer32 | .1.3.6.1.4.1.11898.2.1.2.1.1.1.40 |
| oriWirelessIfDTIMPeriod This object represents the delivery traffic indication map
period. This is the interval between the transmission of multicast
frames on the wireless inteface. It is expressed i… | column | Integer32 | .1.3.6.1.4.1.11898.2.1.2.1.1.1.5 |
| oriWirelessIfChannel This object represents the radio frequency channel for this
wireless interface. The default value for the channel is based on the
regulatory domain. | column | Integer32 | .1.3.6.1.4.1.11898.2.1.2.1.1.1.6 |
| oriWirelessIfDistancebetweenAPs This object identifies the distance between access points.
The default value for this parameter should be large. | column | Enumeration | .1.3.6.1.4.1.11898.2.1.2.1.1.1.7 |
| oriWirelessIfMulticastRate This object is used to configure the multicast rate, but it is
dependent on the type of wireless NIC. The value of this object is
given in 500 Kbps units. This object can be co… | column | Integer32 | .1.3.6.1.4.1.11898.2.1.2.1.1.1.8 |
| oriWirelessIfClosedSystem This object is used as a flag which identifies whether the
device will accept association requests to this interface, for
client stations configured with a network name of 'ANY'… | column | Enumeration | .1.3.6.1.4.1.11898.2.1.2.1.1.1.9 |