gpoeInputPinStatus
OMNITRON-GPOE-NOTIFICATION-MIB ·
.1.3.6.1.4.1.7342.100.0.19
Object
notification
Input pin status - Input pin changed state, either open to closed or closed to open, where gpoeTrapCode indicates the relay state: 1 = open, 2 = closed
Context
- MIB
- OMNITRON-GPOE-NOTIFICATION-MIB
- OID
.1.3.6.1.4.1.7342.100.0.19- Type
- notification
- Status
- current
- Parent
- ostGpoeNotificationCodes
- Siblings
- 51
Syntax
No syntax metadata recorded.
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| gpoeModuleColdStart Module cold start - A module has completed power on testing after
initial power up, where gpoeTrapCode = 0. | notification | - | .1.3.6.1.4.1.7342.100.0.1 |
| gpoeSecondaryLinkUp Secondary link up - Secondary or backup redundant link port is active,
where gpoeTrapCode indicates the port number. | notification | - | .1.3.6.1.4.1.7342.100.0.10 |
| gpoeSecondaryLinkDown Secondary link down - Secondary or backup redundant link port is down,
where gpoeTrapCode indicates the port number. | notification | - | .1.3.6.1.4.1.7342.100.0.11 |
| gpoeStandbyLinkUp Standby link up - Standby redundant link port is up and can become an
active link if the primary link goes down, where gpoeTrapCode
indicates the port number. | notification | - | .1.3.6.1.4.1.7342.100.0.12 |
| gpoeStandbyLinkDown Standby link down - Standby redundant link port is down and cannot
become an active link if the primary link goes down, where
gpoeTrapCode indicates the port number. | notification | - | .1.3.6.1.4.1.7342.100.0.13 |
| gpoeLoopPreventionBlock Loop prevention block - Loop prevention block on a port has occurred
(RSTP block), where gpoeTrapCode indicates the port number. | notification | - | .1.3.6.1.4.1.7342.100.0.14 |
| gpoeLoopPreventionClear Loop prevention clear - Loop prevention block on a port has been
removed (RSTP forward), where gpoeTrapCode indicates the port number. | notification | - | .1.3.6.1.4.1.7342.100.0.15 |
| gpoeHardwareDipSwitchChanged Hardware DIP switch changed - Hardware DIP switch on the module has
changed state, where gpoeTrapCode indicates the switch number. | notification | - | .1.3.6.1.4.1.7342.100.0.16 |
| gpoeSoftwareDipSwitchChanged Software DIP switch changed - Software DIP switch on the module has
changed state, where gpoeTrapCode indicates the switch number. | notification | - | .1.3.6.1.4.1.7342.100.0.17 |
| gpoeOutputRelay Output relay - Output relay changed state, either from activated
to not activated or not activated to activated, where
gpoeTrapCode indicates the relay state:
1 = not activated,… | notification | - | .1.3.6.1.4.1.7342.100.0.18 |
| gpoeModuleReset Module reset - a module completed power on testing after receiving
a reset command via user intervention, where gpoeTrapCode = 0. | notification | - | .1.3.6.1.4.1.7342.100.0.2 |
| gpoeModuleConfigurationChange Module configuration change - A configuration change has been committed
to flash, where gpoeTrapCode = 0. | notification | - | .1.3.6.1.4.1.7342.100.0.20 |
| gpoeModuleOverTemperature Module over temperature - The module has detected that the module
temperature has risen above the safe operating temperature, which is 5
degrees less than the maximum temperature … | notification | - | .1.3.6.1.4.1.7342.100.0.21 |
| gpoeModuleNormalTemperature Module normal temperature - The module has detected a normal operating
temperature range after a temperature out of range (low or high), where
gpoeTrapCode = 0. | notification | - | .1.3.6.1.4.1.7342.100.0.22 |
| gpoeModuleVoltageOutOfRange Module voltage out of range - The module has detected that the internal
operating voltage is greater than 5% or less than 5% of nominal
internal voltage and the event is not gener… | notification | - | .1.3.6.1.4.1.7342.100.0.23 |
| gpoeModuleVoltageRangeNormal Module voltage range normal - The module has detected a normal voltage
range after a voltage out of range (low or high), where
gpoeTrapCode = 0. | notification | - | .1.3.6.1.4.1.7342.100.0.24 |
| gpoePoePdStatusError PoE PD status error - A port on the module has detected a PoE PD
error, where gpoePoeStatus indicates the specific PoE PD error and
gpoeTrapCode indicates the port number. | notification | - | .1.3.6.1.4.1.7342.100.0.25 |
| gpoePoePdStatusNormal PoE PD status normal - A port on the module has detected no PoE PD
errors on a port where previously there had been one or more errors,
where gpoeTrapCode indicates the port numbe… | notification | - | .1.3.6.1.4.1.7342.100.0.26 |
| gpoeAclAccessDenied ACL access denied - The module has detected that access to the
management has been denied using a configured or default ACL, where
gpoeSourceIpString indicates the source IP addre… | notification | - | .1.3.6.1.4.1.7342.100.0.27 |
| gpoeTelnetAuthenticationFailure Telnet authentication failure - The module has detected a Telnet
authentication login failure, where gpoeSourceIpString indicates the
source IP address of the access, gpoeUsername… | notification | - | .1.3.6.1.4.1.7342.100.0.28 |
| gpoeTelnetSessionStarted Telnet session started - The module has detected that a Telnet session
has started, where gpoeSourceIpString indicates the source IP address
of the access, gpoeUsername indicates … | notification | - | .1.3.6.1.4.1.7342.100.0.29 |
| gpoeTelnetSessionStopped Telnet session stopped - The module has detected that a Telnet session
has stopped, where gpoeSourceIpString indicates the source IP address
of the access, gpoeUsername indicates … | notification | - | .1.3.6.1.4.1.7342.100.0.30 |
| gpoeFtpAuthenticationFailure FTP authentication failure - The module has detected an FTP
authentication login failure, where gpoeSourceIpString indicates the
source IP address of the access, gpoeUsername indi… | notification | - | .1.3.6.1.4.1.7342.100.0.31 |
| gpoeFtpSessionStarted FTP session started - The module has detected that a FTP session
has started, where gpoeSourceIpString indicates the source IP address
of the access, gpoeUsername indicates the us… | notification | - | .1.3.6.1.4.1.7342.100.0.32 |
| gpoeFtpSessionStopped FTP session stopped - The module has detected that a FTP session
has stopped, where gpoeSourceIpString indicates the source IP address
of the access, gpoeUsername indicates the us… | notification | - | .1.3.6.1.4.1.7342.100.0.33 |
| gpoeSerialConsoleSessionStarted Serial console port session started - The module has detected that a
serial console session has started, where gpoeUsername indicates the
username and gpoeTrapCode = 0. | notification | - | .1.3.6.1.4.1.7342.100.0.34 |
| gpoeSerialConsoleSessionStopped Serial console port session stopped - The module has detected that a
serial console session has stopped, where gpoeUsername indicates the
username and gpoeTrapCode = 0. | notification | - | .1.3.6.1.4.1.7342.100.0.35 |
| gpoeSshAuthenticationFailure SSH authentication failure - Wrong SSH authentication type or password
is used, where gpoeSourceIpString indicates the source IP address,
gpoeUsername indicates the username, and … | notification | - | .1.3.6.1.4.1.7342.100.0.36 |
| gpoeSshSessionStarted SSH session started - SSH session for a user has started, where
gpoeSourceIpString indicates the source IP address, gpoeUsername
indicates the username, and gpoeTrapCode = 0. | notification | - | .1.3.6.1.4.1.7342.100.0.37 |
| gpoeSshSessionStopped SSH session stopped - SSH session for a user has stopped, where
gpoeSourceIpString indicates the source IP address, gpoeUsername
indicates the username, and gpoeTrapCode = 0. | notification | - | .1.3.6.1.4.1.7342.100.0.38 |
| gpoeWrongPasswordCountExceeded Wrong password count exceeded - The module has detected too many wrong
password attempts (5) and will not validate any password attempts until
the device times out (5 minutes) or … | notification | - | .1.3.6.1.4.1.7342.100.0.39 |
| gpoeModulePowerRemoved Module power removed - The module has detected that incoming voltage
has been removed from a power input or has dropped to zero and is not
generated again unless the module first … | notification | - | .1.3.6.1.4.1.7342.100.0.4 |
| gpoeSfpInserted SFP inserted - SFP has been inserted into a port, where
gpoeTrapCode indicates the port number. | notification | - | .1.3.6.1.4.1.7342.100.0.40 |
| gpoeSfpRemoved SFP removed - SFP has been removed from a port, where gpoeTrapCode
indicates the port number. | notification | - | .1.3.6.1.4.1.7342.100.0.41 |
| gpoeSfpTxLowThreshold SFP transmit low threshold - SFP has detected that the transmission
power on a port is less than the configured threshold warning and
is not generated again unless the module firs… | notification | - | .1.3.6.1.4.1.7342.100.0.42 |
| gpoeSfpTxHighThreshold SFP transmit high threshold - SFP has detected that the transmission
power on a port is greater than the configured threshold warning and
is not generated again unless the module … | notification | - | .1.3.6.1.4.1.7342.100.0.43 |
| gpoeSfpCurrentBiasLowThreshold SFP current bias low threshold - SFP has detected that the current
bias on a port is less than the configured threshold warning and
is not generated again unless the module first … | notification | - | .1.3.6.1.4.1.7342.100.0.44 |
| gpoeSfpCurrentBiasHighThreshold SFP current bias high threshold - SFP has detected that the current
bias on a port is greater than the configured threshold warning and
is not generated again unless the module fi… | notification | - | .1.3.6.1.4.1.7342.100.0.45 |
| gpoeSfp33VLowThreshold SFP 3.3V low threshold - SFP has detected that the 3.3V source
voltage on a port is less than the configured threshold warning and
is not generated again unless the module first d… | notification | - | .1.3.6.1.4.1.7342.100.0.46 |
| gpoeSfp33VHighThreshold SFP 3.3V high threshold - SFP has detected that the 3.3V source
voltage on a port is higher than the configured threshold warning and
is not generated again unless the module firs… | notification | - | .1.3.6.1.4.1.7342.100.0.47 |
| gpoeSfpTempLowThreshold SFP low temperature threshold - SFP has detected that the low
temperature on a port is less than the configured threshold warning and
is not generated again unless the module firs… | notification | - | .1.3.6.1.4.1.7342.100.0.48 |
| gpoeSfpTempHighThreshold SFP high temperature threshold - SFP has detected that the high
temperature on a port is less than the configured threshold warning and
is not generated again unless the module fi… | notification | - | .1.3.6.1.4.1.7342.100.0.49 |
| gpoeModulePowerApplied Module power applied - The module has detected that incoming voltage
has been applied to a power input and is not generated again unless
the module first detects that the power ha… | notification | - | .1.3.6.1.4.1.7342.100.0.5 |
| gpoeSfpRxLowThreshold SFP receive low threshold - SFP has detected that the receive
power on a port is less than the configured threshold warning and
is not generated again unless the module first dete… | notification | - | .1.3.6.1.4.1.7342.100.0.50 |
| gpoeSfpRxHighThreshold SFP receive high threshold - SFP has detected that the receive
power on a port is greater than the configured threshold warning and
is not generated again unless the module first … | notification | - | .1.3.6.1.4.1.7342.100.0.51 |
| gpoeSfpNormal SFP normal - SFP has detected normal operating conditions for the
port, where gpoeTrapCode indicates the port number. | notification | - | .1.3.6.1.4.1.7342.100.0.52 |
| gpoeModuleConfigurationFileCorrupted Module configuration file corrupted - The management module has
detected a corrupted configuration file, where gpoeTrapCode = 0. | notification | - | .1.3.6.1.4.1.7342.100.0.53 |
| gpoeLinkDown Link down - A port on the module has lost link, where gpoeTrapCode
indicates the port number. | notification | - | .1.3.6.1.4.1.7342.100.0.6 |
| gpoeLinkUp Link up - A port on the module has gained link, where gpoeTrapCode
indicates the port number. | notification | - | .1.3.6.1.4.1.7342.100.0.7 |
| gpoePrimaryLinkUp Primary link up - Primary redundant link port is active, where
gpoeTrapCode indicates the port number. | notification | - | .1.3.6.1.4.1.7342.100.0.8 |
| gpoePrimaryLinkDown Primary link down - Primary redundant link port is down, where
gpoeTrapCode indicates the port number. | notification | - | .1.3.6.1.4.1.7342.100.0.9 |
Notification Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| gpoeTrapCode The notification modifier. This can be a port number, input pin, etc. | scalar | OctetString | .1.3.6.1.4.1.7342.100.1.1 |
| gpoeTrapIpString IPv6 or IPv4 address of the module trap source. If no address is
configured the value returned is 0.0.0.0 or 255.255.255.255. | scalar | OctetString | .1.3.6.1.4.1.7342.100.1.2 |
| gpoeTrapModuleDescription The module description | scalar | OctetString | .1.3.6.1.4.1.7342.100.1.3 |