ostEnetStInitCfgSearchType
OMNITRON-EST-MIB ·
.1.3.6.1.4.1.7342.10.1.1.2.1.34
Object
column
r/w
Enumeration
This object selects the specific type of Test Initiator instance.
fixed(1) Test instance decrements based upon the value of
ostEnetStInitCfgFailureDecrementSize. When a test
iteration fails, the test is rerun at the current
rate - the percent value of the initial test
until there is a pass or a zero value is
reached.
binary(2) Test instance decrements by 50% of the previous decrement
value and when it fails and increments by 25% of the
previous decrement value. If the decrement value
falls below ostEnetStInitCfgFailureDecrementSize the
test stops and the last 'Pass' value is displayed.
This object can only be written at row creation time and cannot be
modified once it has been created.
Context
- MIB
- OMNITRON-EST-MIB
- OID
.1.3.6.1.4.1.7342.10.1.1.2.1.34- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- ostEnetStInitCfgEntry
- Table
- ostEnetStInitCfgTable
- Siblings
- 57
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | fixed |
2 | binary |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ostEnetStInitCfgIndex An index to the EnetST Initiator Configuration table which indicates
the specific test session for the module.
ostEnetStGlobalCfgInitSessionNextIndex needs to be in… | column | Unsigned32 | .1.3.6.1.4.1.7342.10.1.1.2.1.1 |
| ostEnetStInitCfgCosBwp This object defines which Class of Service (CoS) or Bandwidth Profile
the test instance is associated with. It must be configured if
ostEnetStInitCfgType is 'evccos'. It is ignore… | column | OMNITRON-TC-MIBOstCosNameString | .1.3.6.1.4.1.7342.10.1.1.2.1.10 |
| ostEnetStInitCfgVid The test VID associated with this EVC on this interface. It must be
a member of the EVC selected by ostEnetStInitCfgEvc.
If defined, it is the value of VLAN ID that… | column | OMNITRON-TC-MIBOstVlanId | .1.3.6.1.4.1.7342.10.1.1.2.1.11 |
| ostEnetStInitCfgPriority This object specifies the test instance PCP value (tag priority) on
the generated test PDU.
It must be configured if ostEnetStInitCfgType 'evc' or 'evccos'
and if t… | column | IEEE8021-TC-MIBIEEE8021PriorityValue | .1.3.6.1.4.1.7342.10.1.1.2.1.12 |
| ostEnetStInitCfgMdIndex This object specifies the test instance maintenance domain index for
the generated test PDU.
The value is ignored for ostEnetStInitCfgType 'port', 'evc', or 'evccos… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7342.10.1.1.2.1.13 |
| ostEnetStInitCfgMaIndex This object specifies the test instance maintenance association index
for the generated test PDU.
The value is ignored for ostEnetStInitCfgType 'port', 'evc', or 'e… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7342.10.1.1.2.1.14 |
| ostEnetStInitCfgDestMacAddress This object specifies the Destination MAC Address Field for
test instance PDUs.
If ostEnetStInitCfgType is 'port', 'evc', or 'evccos' the value
of the object is use… | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.7342.10.1.1.2.1.15 |
| ostEnetStInitCfgDestIsMepId This object indicates whether the destination MEP is identified via
its MEP ID or its MAC address.
If ostEnetStInitCfgType is 'port', 'evc', or 'evccos' the
value o… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7342.10.1.1.2.1.16 |
| ostEnetStInitCfgDestMepId The Maintenance End Point Identifier of another MEP in the same
Maintenance Association to which the test instance PDU is to be sent.
This MEP ID will be used if th… | column | IEEE8021-CFM-MIBDot1agCfmMepIdOrZero | .1.3.6.1.4.1.7342.10.1.1.2.1.17 |
| ostEnetStInitCfgFrameSize This object defines which values of frame sizes to use during
a test instance.
This object can only be written at row creation time and cannot be
modified once it h… | column | OMNITRON-TC-MIBOstFrameSizeList | .1.3.6.1.4.1.7342.10.1.1.2.1.18 |
| ostEnetStInitCfgFrameType Deprecated. The value of this object is ignored | column | Enumeration | .1.3.6.1.4.1.7342.10.1.1.2.1.19 |
| ostEnetStInitCfgRowStatus The status of the row.
The writable columns in a row cannot be changed if the row
is active. All columns must have a valid value before a row
can be activated. | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.7342.10.1.1.2.1.2 |
| ostEnetStInitCfgFramePayload This object selects the specific type of test instance frame
type.
zeros(1) Test instance frame payload is all zeros
ones(2) Test instance frame payload … | column | Enumeration | .1.3.6.1.4.1.7342.10.1.1.2.1.20 |
| ostEnetStInitCfgFrameTimeDurationType This object selects the specific time duration that is indicated
by ostEnetStInitCfgFrameDuration for the test instance.
type.
framecount(1) Test instance dura… | column | Enumeration | .1.3.6.1.4.1.7342.10.1.1.2.1.21 |
| ostEnetStInitCfgFrameDuration This object specifies the duration of a test instance trial.
If ostEnetStInitCfgFrameTimeDurationType is 'framecount' the value of the
object indicates the number o… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7342.10.1.1.2.1.22 |
| ostEnetStInitCfgFrameRateType This object selects the specific frame rate that is indicated
by ostEnetStInitCfgFrameRate for the test instance.
bits(1) Test instance frame rate specif… | column | Enumeration | .1.3.6.1.4.1.7342.10.1.1.2.1.23 |
| ostEnetStInitCfgFrameRate This object specifies the specific frame rate of a test instance.
This object is valid for the GMx family of products. It is undefined
for the XMx family of products.
… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7342.10.1.1.2.1.24 |
| ostEnetStInitCfgTestType This object selects the specific type of test instance.
loss(1) Test instance is RFC2544 Loss test
latency(2) Test instance is RFC2544 Latency te… | column | Enumeration | .1.3.6.1.4.1.7342.10.1.1.2.1.25 |
| ostEnetStInitCfgAcceptableFrameLossType This object selects the specific type of acceptable frame loss
before a trial failure is declared as indicated by
ostEnetStInitCfgAcceptableFrameLoss for the test instance.
… | column | Enumeration | .1.3.6.1.4.1.7342.10.1.1.2.1.26 |
| ostEnetStInitCfgAcceptableFrameLoss This object specifies the acceptable frame loss in a trial before
a trial failure is declared in a test instance.
If ostEnetStInitCfgAcceptableFrameLossType is 'fra… | column | Unsigned32 | .1.3.6.1.4.1.7342.10.1.1.2.1.27 |
| ostEnetStInitCfgTrialCount This object specifies the number of trials to run for a specific
test instance for a specific iteration. An iteration is one test run
that runs for a specific time duration.
… | column | Unsigned32 | .1.3.6.1.4.1.7342.10.1.1.2.1.28 |
| ostEnetStInitCfgStatClear This object when written clears the statistic counters associated with
a specific test instance. When read the value always returns 'false'.
Writing this value does… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7342.10.1.1.2.1.29 |
| ostEnetStInitCfgProfileName Test Initiator profile name.
This object may not be modified after creation. | column | OMNITRON-TC-MIBOstProfileNameString | .1.3.6.1.4.1.7342.10.1.1.2.1.3 |
| ostEnetStInitCfgEgressPortNum This object selects the egress port number for the specific test
instance that is configured. The initiating port for the specific test
instance is configured via the ostEnetStIni… | column | OMNITRON-TC-MIBOstPortNumber | .1.3.6.1.4.1.7342.10.1.1.2.1.30 |
| ostEnetStInitCfgTestStatus This object indicates the status of the currently indicated Test
Instance.
If a value of testInitializing(5) is written to the object the
test will be restarted, wh… | column | OMNITRON-TC-MIBOstTestStatusType | .1.3.6.1.4.1.7342.10.1.1.2.1.31 |
| ostEnetStInitCfgPacketSizeType This object selects the type of packet to be used for calculating the
time between frame starts.
l1(1) Uses the frame size + preamble/start (8 bytes) + inter-p… | column | Enumeration | .1.3.6.1.4.1.7342.10.1.1.2.1.32 |
| ostEnetStInitCfgFailureDecrementSize This object contains the maximum resolution for ascertaining a passing
rate for a test.
If 'ostEnetStInitCfgSearchType' is 'fixed' and a test fails, the test
rate i… | column | percent Unsigned32 | .1.3.6.1.4.1.7342.10.1.1.2.1.33 |
| ostEnetStInitCfgAcceptableFrameDelay This object specifies the acceptable frame delay in a trial before
a trial failure is declared in a test instance.
This object is used for Y.1564 testing only.
… | column | microseconds Unsigned32 | .1.3.6.1.4.1.7342.10.1.1.2.1.35 |
| ostEnetStInitCfgAcceptableIfdv This object specifies the acceptable inter-frame delay in a trial before
a trial failure is declared in a test instance.
This object is used for Y.1564 testing only… | column | microseconds Unsigned32 | .1.3.6.1.4.1.7342.10.1.1.2.1.36 |
| ostEnetStInitCfgNameType This object selects the packet name type for the associated Test
Instance, either CoS or BWP profile name.
cos(1) The ostEnetStInitCfgCosBwp object indicates th… | column | Enumeration | .1.3.6.1.4.1.7342.10.1.1.2.1.37 |
| ostEnetStInitCfgVidTx The VID associated with the Test PDUs for the Test Instance.
If the primary VID was selected it indicates the Primary VID used. If
the primary VID was not selected … | column | OMNITRON-TC-MIBOstVlanId | .1.3.6.1.4.1.7342.10.1.1.2.1.38 |
| ostEnetStInitCfgRemote This object selects the specific type of remote protocol for the specific
Test Initiator instance.
none(1) Test instance is independent of loop up/down protoc… | column | Enumeration | .1.3.6.1.4.1.7342.10.1.1.2.1.39 |
| ostEnetStInitCfgTestGenerator This object specifies whether the Test Initiator function is
enabled for the test instance.
The value 'true' indicates the Test Initiator function is enabled
for th… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7342.10.1.1.2.1.4 |
| ostEnetStInitCfgDestIpAddress This object indicates the destination IPv4 address of the specific
test instance for an L3 type of test.
A non-zero value for this object indicates that the Etherne… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.7342.10.1.1.2.1.40 |
| ostEnetStInitCfgSrcIpAddress This object indicates the source IPv4 address of the specific test
instance for an L3 type of test
A non-zero value for this object or ostEnetStInitCfgSrcIpAddressS… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.7342.10.1.1.2.1.41 |
| ostEnetStInitCfgDisableTimeStamp This object selects whether the timestamp is added to the Data or Test
TLV.
noTimeStamp(1) Test frames do not include originating timestamp
addTimeStamp(2) Test … | column | Enumeration | .1.3.6.1.4.1.7342.10.1.1.2.1.42 |
| ostEnetStInitCfgIngressPolicers This object selects whether the ingress policers are used for generation
of test traffic.
noIngressPolicers(1) No ingress policers are used for traffic generation
… | column | Enumeration | .1.3.6.1.4.1.7342.10.1.1.2.1.43 |
| ostEnetStInitCfgY1564FullCir This object selects whether the A.1 (full CIR) or A.2 (step CIR) test
is run. This is applicable to Y.1564 test only and is ignored for other
test types
… | column | Enumeration | .1.3.6.1.4.1.7342.10.1.1.2.1.44 |
| ostEnetStInitCfgY1564Performance This object selects whether the configuration tests A, B, and C are
run or whether the performance test A is run. This is applicable to
Y.1564 test only and is ignored for other t… | column | Enumeration | .1.3.6.1.4.1.7342.10.1.1.2.1.45 |
| ostEnetStInitCfgY1564UseEir This object selects whether the CIR test (Test A) uses CIR or EIR
when running the test. This allows the test to run and stay in
sync with other tests running of the bandwidth pro… | column | Enumeration | .1.3.6.1.4.1.7342.10.1.1.2.1.46 |
| ostEnetStInitCfgFrameRate64 This object specifies the specific frame rate of a test instance.
This object is used only for the XM5. It is undefined for the GMx
family of products.
… | column | OMNITRON-TC-MIBOstUnsigned64 | .1.3.6.1.4.1.7342.10.1.1.2.1.47 |
| ostEnetStInitCfgAvail This object specifies the acceptable AVAIL (availability) in a trial
before a trial failure is declared in a test instance. If availablilty
drops below the configured value a tria… | column | milli-percent Unsigned32 | .1.3.6.1.4.1.7342.10.1.1.2.1.48 |
| ostEnetStInitCfgEthertype This object specifies the test instance Ethertype that is used at the
start of the data portion of the frame at the VID TAG.
The value is ignored for ostEnetStInitC… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7342.10.1.1.2.1.49 |
| ostEnetStInitCfgTestMonitor This object specifies whether the Test Monitor function is
enabled for the test instance.
The value 'true' indicates the Test Monitor function is enabled
for the te… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7342.10.1.1.2.1.5 |
| ostEnetStInitCfgDestIpAddressString This object indicates the destination IPv4 or IPv6 address of the
specific test instance for an L3 type of test.
A non-zero value for this object indicates that the… | column | OMNITRON-TC-MIBOstIpAddr | .1.3.6.1.4.1.7342.10.1.1.2.1.50 |
| ostEnetStInitCfgSrcIpAddressString This object indicates the source IPv4 or IPv6 address of the
specific test instance for an L3 type of test
A non-zero value for this object indicates that the Ether… | column | OMNITRON-TC-MIBOstIpAddr | .1.3.6.1.4.1.7342.10.1.1.2.1.51 |
| ostEnetStInitCfgUpPort This object allows an egress port to be dynamically determined by
sending traffic out all the ports in an EVC instead of a specific
egress port (ostEnetStInitCfgEgressPortNum).
… | column | Enumeration | .1.3.6.1.4.1.7342.10.1.1.2.1.52 |
| ostEnetStInitCfgCtlIpAddressString This object indicates the control IPv4 or IPv6 address of the
specific test instance for remote protocol type of test.
It is illegal to set this when the ostEnetStI… | column | OMNITRON-TC-MIBOstIpAddr | .1.3.6.1.4.1.7342.10.1.1.2.1.53 |
| ostEnetStInitCfgTwampServerPort TWAMP server TCP port | column | Unsigned32 | .1.3.6.1.4.1.7342.10.1.1.2.1.54 |
| ostEnetStInitCfgTwampUdpSrcPort TWAMP or SFP-NID L3 PDU data or SFP-NID IP Loopback remote protocol
UDP source port. When used in a standard L3 loopback the transmitted
frame is a UDP L4 frame. | column | Unsigned32 | .1.3.6.1.4.1.7342.10.1.1.2.1.55 |
| ostEnetStInitCfgTwampUdpDstPort TWAMP or SFP-NID L3 PDU data or SFP-NID IP Loopback remote protocol
UDP destination port. When used in a standard L3 loopback the
transmitted frame is a UDP L4 frame. | column | Unsigned32 | .1.3.6.1.4.1.7342.10.1.1.2.1.56 |
| ostEnetStInitCfgGatewayIpAddressString This object indicates the gateway IPv4 or IPv6 address of the
specific test instance for remote protocol IP Loopback type of test
for the SFP-NID.
It is illegal to … | column | OMNITRON-TC-MIBOstIpAddr | .1.3.6.1.4.1.7342.10.1.1.2.1.57 |
| ostEnetStInitCfgNetworkAddressLength This object configures the IPv4 subnet mask bit length (maximum size
of 28) or the IPv6 prefix bit length (maximum size of 128) for the
SFP-NID.
This object can onl… | column | Unsigned32 | .1.3.6.1.4.1.7342.10.1.1.2.1.58 |
| ostEnetStInitCfgInService This object specifies whether the Test In-Service function is
enabled for the test instance.
The value 'true' indicates the Test In-Service function is enabled
for … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7342.10.1.1.2.1.6 |
| ostEnetStInitCfgPortNum This object selects the initiating port number for the specific test
instance that is configured. The egress port the specific test
instance is configured via the ostEnetStInitCfg… | column | OMNITRON-TC-MIBOstPortNumber | .1.3.6.1.4.1.7342.10.1.1.2.1.7 |
| ostEnetStInitCfgType This object selects the specific type of Test Initiator instance.
port(1) Test instance is port based
evc(2) Test instance is EVC based
evccos(3) T… | column | Enumeration | .1.3.6.1.4.1.7342.10.1.1.2.1.8 |
| ostEnetStInitCfgEvc This object defines which EVC the test instance is associated with.
It must be configured if ostEnetStInitCfgType is 'evc' or 'evccos'. It
is ignored for other test instance types… | column | OMNITRON-TC-MIBOstEvcNameString | .1.3.6.1.4.1.7342.10.1.1.2.1.9 |