oaLdCardPortsLoopBack
OADWDM-MIB ·
.1.3.6.1.4.1.6926.1.41.8.1.1.8
Object
column
mandatory
r/w
Enumeration
Transponder LoopBack state.
Indicates the transponder LoopBack state.
2 - normal - Transponder card is in non-loopback state
3 - remoteLoopback - Transponder card is in remote loopback state
4 - localLoopback - Transponder card is in local loopback state
5 - lineLoopbackEnable - OCM module is in (LLEB)
line loopback enable state
6 - diagnosticLoopbackEnable - OCM module is in (DLEB)
diagnostic loopback enablestate
Context
- MIB
- OADWDM-MIB
- OID
.1.3.6.1.4.1.6926.1.41.8.1.1.8- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- oaLdCardPortsStatEntry
- Table
- oaLdCardPortsStatTable
- Siblings
- 45
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | other |
2 | normal |
3 | remoteLoopback |
4 | localLoopback |
5 | lineLoopbackEnable |
6 | diagnosticLoopbackEnable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| oaLdCardPortsSlotNumber mandatory The slot#. An index from 1 to The number of slots | column | Integer32 | .1.3.6.1.4.1.6926.1.41.8.1.1.1 |
| oaLdCardPortsCounters mandatory When read :
1 - Counter feature is NOT supported
2 - Counter feature is supported
4 - Extended ethernet counters are supported
When write:
3 - Clear all port conters | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.12 |
| oaLdCardPortsCounter1Low mandatory The number of bytes received at the port.
This object returns the least significant 32 bits of a 64 bits counter.
To calculate the actual counter reading, use the following formul… | column | RFC1155-SMICounter | .1.3.6.1.4.1.6926.1.41.8.1.1.14 |
| oaLdCardPortsCounter1High mandatory The number of bytes received at the port.
This object returns the most significant 32 bits of a 64 bits counter.
To calculate the actual counter reading, use the following formula… | column | RFC1155-SMICounter | .1.3.6.1.4.1.6926.1.41.8.1.1.15 |
| oaLdCardPortsCounter2Low mandatory The number of error bytes received at the port.
This object returns the least significant 32 bits of a 64 bits counter.
To calculate the actual counter reading, use the following … | column | RFC1155-SMICounter | .1.3.6.1.4.1.6926.1.41.8.1.1.17 |
| oaLdCardPortsCounter2High mandatory The number of error bytes received at the port.
This object returns the most significant 32 bits of a 64 bits counter.
To calculate the actual counter reading, use the following f… | column | RFC1155-SMICounter | .1.3.6.1.4.1.6926.1.41.8.1.1.18 |
| oaLdCardPortsPortNumber mandatory The port#. An index from 1 to The number of ports | column | Integer32 | .1.3.6.1.4.1.6926.1.41.8.1.1.2 |
| oaLdCardPortsConnectorType mandatory Port Connector Types:
other - 1 - Unknown type of connector
static- 2 - Not Changeable (fix) type of connector
gbic - 3 - GBIC type of connector
sfp - 4 - SFP type of connecto… | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.20 |
| oaLdCardPortsConnectorSubType mandatory Port Connector Physical Sub Type:
other -1 - Unknown or N/A Connector's connectivity Type
rj45 -2 - Copper RJ45
sc -3 - Regular Fibre Optic [FO]
lc -4 - LC
mtrj … | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.21 |
| oaLdCardPortsRate mandatory | column | RateMode | .1.3.6.1.4.1.6926.1.41.8.1.1.22 |
| oaLdCardPortsLineLength mandatory T1 ports line length:
other - 1 - Unknown line length
from0to133 - 2 - line length 0 - 133 ft. (0.6 dB)
from133to266 - 3 - line length 133 - 266 ft. (1.2 dB)
from266to399… | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.23 |
| oaLdCardPortsAccessLinState mandatory Port LIN status.
Indicates the Port access LIN status.
2 - Enable - Access LIN is enabled
3 - Disable - Access LIN is disabled | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.24 |
| oaLdCardPortsFlowControlMode mandatory Module Flow Control Mode.
Indicates the flow control mode for 10GbE access.
2 - Enable - Flow Control is enabled
3 - Disable - Flow Control is disabled | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.25 |
| oaLdCardPortsDryContactStat mandatory Port Dry Contact State.
Indicates the Port Dry Contact State.
2 - open - Dry Contact is open
3 - close - Dry Contact is close | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.26 |
| oaLdCardPortsPowerTuning mandatory Port Power Tuning in dB of the E&M signal.
(20) is returned if this value is undefined. | column | Integer32 | .1.3.6.1.4.1.6926.1.41.8.1.1.27 |
| oaLdCardPortsMediaType mandatory Type of Media. | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.28 |
| oaLdCardPortsEMCfgOperation mandatory Specify the operation of the E&M signal.
twoWires - 2-wire operation.
fourWires - 4-wire operation. | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.29 |
| oaLdCardPortsLink mandatory Indicates the link status of the port
2 - link on
3 - link off | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.3 |
| oaLdCardPortsEyemaxState mandatory EyeMax state mode, (applicable only for ports that support this (EYEMAX) features)
other - Port does not support this feature,
disable - no Eyemax mode,
scanning - start scan proc… | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.30 |
| oaLdCardPortsEyemaxOperFactor mandatory EyeMax Operational Calibrate factor, This value represents current DAC output.
When this feature is not supported (0) is returned.
Units: percent. | column | percent Integer32 | .1.3.6.1.4.1.6926.1.41.8.1.1.31 |
| oaLdCardPortsEyemaxAdminFactor mandatory EyeMax Administrative Calibration factor, This value is represents
the value to be set into DAC.
After scan operation it holds the optimal value that should be set into DAC.
Users… | column | percent Integer32 | .1.3.6.1.4.1.6926.1.41.8.1.1.32 |
| oaLdCardPortsFefMode mandatory Port Far End Failure (FEF) Detection mode.
2 - Enable - FEF is enabled
3 - Disable - FEF is disabled | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.33 |
| oaLdCardPortsOdu1Index mandatory For clients that mapped into the OTN payload.
Indicates the index of the OPU-1 payload area.
0 - not supported, or client is not configured.
1 - Client mapped into OPU-1 #1 paylo… | column | Integer32 | .1.3.6.1.4.1.6926.1.41.8.1.1.34 |
| oaLdCardPortsOdu1TsIndex mandatory For clients that mapped into the OTN payload.
Indicates the tributary slot index among the 16 tributary slots,
of the OPU-1 payload area.
0 - not supported, or client is not… | column | Integer32 | .1.3.6.1.4.1.6926.1.41.8.1.1.35 |
| oaLdCardPortsPmMode mandatory Port Performance Monitoring Mode.
Indicates the Port Performance Monitoring mode.
2 - Enable - PM is enabled for this port
3 - Disable - PM is disabled for tthis port | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.36 |
| oaLdCardPortsFecMode mandatory The Forward Error Correction (FEC) mode which is used
in the selected port.
2 - g709 - Standard G.709 FEC mode.
3 - eFec - Enhanced FEC proprietary mode.
4 - byPass - Bypass FEC … | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.37 |
| oaLdCardPortsLock mandatory Port PLL lock mode.
2 - locked - PLL was locked,
3 - notlocked - PLL was not locked | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.38 |
| oaLdCardPortsLaserMode mandatory Port Laser Mode.
Indicates the port laser mode.
2 - Enable - Laser is enabled
3 - Disable - Laser is disabled (can not transmit) | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.39 |
| oaLdCardPortsActivity mandatory Indicates the activety status of the port
2 - activety on
3 - activety off | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.4 |
| oaLdCardPortsOdu1TsSize mandatory For clients that mapped into the OTN payload.
Indicates the number of tributary slots that are occupied by the client's rate.
0 - not supported, or client is not configured. | column | Integer32 | .1.3.6.1.4.1.6926.1.41.8.1.1.40 |
| oaLdCardPortsSpeed mandatory Ports speed mode. | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.41 |
| oaLdCardPortsPriorityClockSource mandatory Defines the port's priority in relation to the clock source.
1 defines the highest priority index and the last port index
defines the least prioritized port.
The highest priority… | column | Integer32 | .1.3.6.1.4.1.6926.1.41.8.1.1.42 |
| oaLdCardPortsActionMode mandatory | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.43 |
| oaLdCardPortsOutputPortId mandatory | column | Integer32 | .1.3.6.1.4.1.6926.1.41.8.1.1.44 |
| oaLdCardPortsGroupId mandatory | column | Integer32 | .1.3.6.1.4.1.6926.1.41.8.1.1.45 |
| oaLdCardPortsChannelId mandatory | column | Integer32 | .1.3.6.1.4.1.6926.1.41.8.1.1.46 |
| oaLdCardPortsAutoShutdownMode mandatory Port Auto Shutdown Mode.
Indicates the port Auto Shutdown (eye safe) mode.
2 - Enable - Auto Shutdown mode is enabled
3 - Disable - Auto Shutdown mode is disabled. | column | Enumeration | .1.3.6.1.4.1.6926.1.41.8.1.1.47 |
| oaLdCardPortsEymxScnAmpFctr mandatory Initialization value for Amlification Factor used
in the Eyemax scanning operation in 0.1 units. | column | Integer32 | .1.3.6.1.4.1.6926.1.41.8.1.1.48 |
| oaLdCardPortsEymxScnAmpFctrMin mandatory Minimum value that can be set for
Initialization of the Amlification Factor used
in the Eyemax scanning operation in 0.1 units. | column | Integer32 | .1.3.6.1.4.1.6926.1.41.8.1.1.49 |
| oaLdCardPortsEymxScnAmpFctrMax mandatory Maximum value that can be set for
Initialization of the Amlification Factor used
in the Eyemax scanning operation in 0.1 units. | column | Integer32 | .1.3.6.1.4.1.6926.1.41.8.1.1.50 |
| oaLdCardPortsEymxScnDspComps mandatory Initialization value for Dispersion Compensation
used in the Eyemax scanning operation. | column | Integer32 | .1.3.6.1.4.1.6926.1.41.8.1.1.51 |
| oaLdCardPortsEymxScnTreshold mandatory Initialization value for Rx threshold
used in the Eyemax scanning operation. | column | percent Integer32 | .1.3.6.1.4.1.6926.1.41.8.1.1.52 |
| oaLdCardPortsEymxScnOperComplt mandatory Indication how much of the scanning operation
have been already completed (in percents 0 - 100). | column | percent Integer32 | .1.3.6.1.4.1.6926.1.41.8.1.1.53 |
| oaLdCardPortsEymxScnResult mandatory Indication if the scanning operation ended
properly or finished with problems. | column | RFC1213-MIBDisplayString | .1.3.6.1.4.1.6926.1.41.8.1.1.54 |
| oaLdCardPortsWaveLength mandatory The port laser wavelength (Lambda channel) in units of nm (Nanometer).
Returns 0 when not applicable | column | Integer32 | .1.3.6.1.4.1.6926.1.41.8.1.1.6 |