adminSwitchPortMirror

NEXANS-BM-MIB · .1.3.6.1.4.1.266.20.2.11
MIB view Table view

Object

scalar r/w Enumeration 
If set to enable(1), the switch doesn't use address learning.
This affects that any received packet will be forwarded to all ports
of the particular VLAN. The switch acts like a hub within each VLAN.

Context

MIB
NEXANS-BM-MIB
OID
.1.3.6.1.4.1.266.20.2.11
Type
scalar
Access
readwrite
Status
current
Parent
bmSwitchAdmin
Siblings
27

Syntax

Enumeration

Values & Constraints

Enumerated Values
1enable
2disable

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
adminReset
Writing this object causes the switch to perform a reset operation. The following reset types are supported. Set Values: resetCounters(2) This action resets all error and stat…
scalarEnumeration.1.3.6.1.4.1.266.20.2.1
adminAddrAgingTimeMinutes
The timeout period in minutes for aging out dynamically learned MAC addresses . The allowed range is 1 minute to 68 minutes.
scalarInteger32.1.3.6.1.4.1.266.20.2.10
adminMgmtAccessList
If set to enableForNexManAccess(2) or enableForAllAccess(3), the switch only accepts read or write requests from IP addresses which are listed in the management accesslist.
scalarEnumeration.1.3.6.1.4.1.266.20.2.12
adminSwitchPoEPowerLimit
The limit for the POE input power from the power supply in VA. If the current power exceeds this value a overload conditions occurs and the inline power for the highest port numb…
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.266.20.2.13
adminSwitchVlanTableMode
If set to staticMode(1) or staticModeVlans64(3) any existing VLAN table entry must be removed manually by management. With staticMode(1) total 16 VLAN-ID's and with staticModeVla…
scalarEnumeration.1.3.6.1.4.1.266.20.2.14
adminUnsecureVlanId
The VLAN-ID of the unsecure VLAN
scalarInteger32.1.3.6.1.4.1.266.20.2.15
adminDot1xAuthFailureVlanId
The VLAN-ID in the case of an IEEE802.1X authentication failure. Setting the VLAN-ID to 0 disables the authentication failure VLAN.
scalarInteger32.1.3.6.1.4.1.266.20.2.16
adminTftpAccess
If 'TFTP authentication via SNMP' is disabled, this value is allways tftpAccessDisable(1). If 'TFTP authentication via SNMP' is read/only or read/write, an this object is read, th…
scalarEnumeration.1.3.6.1.4.1.266.20.2.17
adminSnmpMacTableMode
If set to listAllPorts(1) the BRIDGE-MIBs dot1dTpFdbTable lits MAC address of all ports. If set to listUserPortsOnly(2) the BRIDGE-MIBs dot1dTpFdbTable lits only MAC addresses of…
scalarEnumeration.1.3.6.1.4.1.266.20.2.18
adminAlarmM1
The current setup of the industrial alarm output M1.
scalarEnumeration.1.3.6.1.4.1.266.20.2.19
adminAgentDhcp
If set to enable(1), the switch tries to get his IP parameter via DHCP. If set to disable(2), the switch uses the IP parameters defined with adminIpAddress, adminDefRouterIpAddres…
scalarEnumeration.1.3.6.1.4.1.266.20.2.2
adminAlarmM2
The current setup of the industrial alarm output M2.
scalarEnumeration.1.3.6.1.4.1.266.20.2.20
adminMemoryCardMode
If set to mcDisabled(2), the memory card is disabled but may be re-enabled later by writing mcEnabled(1). If set to mcPermanentDisabled(3), the memory card is disabled permanentl…
scalarEnumeration.1.3.6.1.4.1.266.20.2.21
adminAlarmNameM1
An administratively assigned name for alarm output M1. The configured name will be send as part of alarm message switchIndustrialAlarmM1.
scalarOctetString.1.3.6.1.4.1.266.20.2.22
adminAlarmNameM2
An administratively assigned name for alarm output M1. The configured name will be send as part of alarm message switchIndustrialAlarmM2.
scalarOctetString.1.3.6.1.4.1.266.20.2.23
adminFunctionInputNameF1
An administratively assigned name for function input F1. The configured name will be send as part of alarm message switchFunctionInputAlarm.
scalarOctetString.1.3.6.1.4.1.266.20.2.24
adminLedGlobalMode
Set the global mode for all front side LEDs.
scalarEnumeration.1.3.6.1.4.1.266.20.2.25
adminFunctionInputNameF2
An administratively assigned name for function input F2. The configured name will be send as part of alarm message switchFunctionInputAlarm.
scalarOctetString.1.3.6.1.4.1.266.20.2.26
adminFunctionInputNameF3
An administratively assigned name for function input F2. The configured name will be send as part of alarm message switchFunctionInputAlarm.
scalarOctetString.1.3.6.1.4.1.266.20.2.27
adminFunctionInputNameF4
An administratively assigned name for function input F2. The configured name will be send as part of alarm message switchFunctionInputAlarm.
scalarOctetString.1.3.6.1.4.1.266.20.2.28
adminAgentIpAddress
The IP address of the switch agent's ethernet interface. If the value of adminDHCP is enable(1) this value is read-only. Changes of this value will take affect after the next swit…
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.266.20.2.3
adminAgentPhysAddress
The Ethernet MAC address of the switch agent.
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.266.20.2.4
adminAgentDefRouterIpAddress
The IP address of the default Router. If the value of adminDHCP is enable(1) this value is read-only. Changes of this value will take affect after the next switch reboot or after …
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.266.20.2.5
adminAgentNetmask
The IP Netmask of the connected network. If the value of adminDHCP is enable(1) this value is read-only. Changes of this value will take affect after the next switch reboot or aft…
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.266.20.2.6
adminAgentDhcpServerIpAddress
The IP address of the last used DHCP server.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.266.20.2.7
adminAgentVlanId
The VLAN-ID assigned to the agent. Changes of this value will take affect after the next switch reboot or after setting adminReset to renewIpAndVlanParameter(5).
scalarInteger32.1.3.6.1.4.1.266.20.2.8
adminAgentPrioValue
The IEEE802.1Q priority value and queue assigned to all frames transmitted by the agent. The definition between value, service class and queue are as follows: 0=Best Effort (queue…
scalarInteger32.1.3.6.1.4.1.266.20.2.9