adminMemoryCardMode
NEXANS-BM-MIB ·
.1.3.6.1.4.1.266.20.2.21
Object
scalar
r/w
Enumeration
If set to mcDisabled(2), the memory card is disabled but may be re-enabled later by writing mcEnabled(1). If set to mcPermanentDisabled(3), the memory card is disabled permanently and can't be re-enabled by management or any kind of hardware reset. If set to mcEnabledWithAes256(5), the configuration is stored with AES-256 encryption. If set to mcEnabledWithAes256AndFw(6), the configuration with AES-256 encryption and the firmware are stored.
Context
- MIB
- NEXANS-BM-MIB
- OID
.1.3.6.1.4.1.266.20.2.21- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- bmSwitchAdmin
- Siblings
- 27
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | notSupported |
2 | mcEnabled |
3 | mcDisabled |
4 | mcPermanentDisabled |
5 | mcEnabledWithAes256 |
6 | mcEnabledWithAes256AndFw |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| adminReset Writing this object causes the switch to perform a reset operation.
The following reset types are supported.
Set Values:
resetCounters(2)
This action resets all error and stat… | scalar | Enumeration | .1.3.6.1.4.1.266.20.2.1 |
| adminAddrAgingTimeMinutes The timeout period in minutes for aging out dynamically
learned MAC addresses . The allowed range is 1 minute
to 68 minutes. | scalar | Integer32 | .1.3.6.1.4.1.266.20.2.10 |
| adminSwitchPortMirror If set to enable(1), the switch doesn't use address learning.
This affects that any received packet will be forwarded to all ports
of the particular VLAN. The switch acts like a h… | scalar | Enumeration | .1.3.6.1.4.1.266.20.2.11 |
| adminMgmtAccessList If set to enableForNexManAccess(2) or enableForAllAccess(3), the
switch only accepts read or write requests from IP addresses which
are listed in the management accesslist. | scalar | Enumeration | .1.3.6.1.4.1.266.20.2.12 |
| adminSwitchPoEPowerLimit The limit for the POE input power from the power supply in VA.
If the current power exceeds this value a overload conditions occurs and
the inline power for the highest port numb… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.266.20.2.13 |
| adminSwitchVlanTableMode If set to staticMode(1) or staticModeVlans64(3) any existing VLAN table entry
must be removed manually by management. With staticMode(1) total 16 VLAN-ID's
and with staticModeVla… | scalar | Enumeration | .1.3.6.1.4.1.266.20.2.14 |
| adminUnsecureVlanId The VLAN-ID of the unsecure VLAN | scalar | Integer32 | .1.3.6.1.4.1.266.20.2.15 |
| adminDot1xAuthFailureVlanId The VLAN-ID in the case of an IEEE802.1X authentication failure.
Setting the VLAN-ID to 0 disables the authentication failure VLAN. | scalar | Integer32 | .1.3.6.1.4.1.266.20.2.16 |
| adminTftpAccess If 'TFTP authentication via SNMP' is disabled, this value is allways
tftpAccessDisable(1).
If 'TFTP authentication via SNMP' is read/only or read/write, an this
object is read, th… | scalar | Enumeration | .1.3.6.1.4.1.266.20.2.17 |
| adminSnmpMacTableMode If set to listAllPorts(1) the BRIDGE-MIBs dot1dTpFdbTable lits MAC address
of all ports.
If set to listUserPortsOnly(2) the BRIDGE-MIBs dot1dTpFdbTable lits only
MAC addresses of… | scalar | Enumeration | .1.3.6.1.4.1.266.20.2.18 |
| adminAlarmM1 The current setup of the industrial alarm output M1. | scalar | Enumeration | .1.3.6.1.4.1.266.20.2.19 |
| adminAgentDhcp If set to enable(1), the switch tries to get his IP parameter
via DHCP. If set to disable(2), the switch uses the IP parameters
defined with adminIpAddress, adminDefRouterIpAddres… | scalar | Enumeration | .1.3.6.1.4.1.266.20.2.2 |
| adminAlarmM2 The current setup of the industrial alarm output M2. | scalar | Enumeration | .1.3.6.1.4.1.266.20.2.20 |
| adminAlarmNameM1 An administratively assigned name for alarm output M1.
The configured name will be send as part of alarm message
switchIndustrialAlarmM1. | scalar | OctetString | .1.3.6.1.4.1.266.20.2.22 |
| adminAlarmNameM2 An administratively assigned name for alarm output M1.
The configured name will be send as part of alarm message
switchIndustrialAlarmM2. | scalar | OctetString | .1.3.6.1.4.1.266.20.2.23 |
| adminFunctionInputNameF1 An administratively assigned name for function input F1.
The configured name will be send as part of alarm message
switchFunctionInputAlarm. | scalar | OctetString | .1.3.6.1.4.1.266.20.2.24 |
| adminLedGlobalMode Set the global mode for all front side LEDs. | scalar | Enumeration | .1.3.6.1.4.1.266.20.2.25 |
| adminFunctionInputNameF2 An administratively assigned name for function input F2.
The configured name will be send as part of alarm message
switchFunctionInputAlarm. | scalar | OctetString | .1.3.6.1.4.1.266.20.2.26 |
| adminFunctionInputNameF3 An administratively assigned name for function input F2.
The configured name will be send as part of alarm message
switchFunctionInputAlarm. | scalar | OctetString | .1.3.6.1.4.1.266.20.2.27 |
| adminFunctionInputNameF4 An administratively assigned name for function input F2.
The configured name will be send as part of alarm message
switchFunctionInputAlarm. | scalar | OctetString | .1.3.6.1.4.1.266.20.2.28 |
| adminAgentIpAddress The IP address of the switch agent's ethernet interface.
If the value of adminDHCP is enable(1) this value is read-only.
Changes of this value will take affect after the next swit… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.266.20.2.3 |
| adminAgentPhysAddress The Ethernet MAC address of the switch agent. | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.266.20.2.4 |
| adminAgentDefRouterIpAddress The IP address of the default Router.
If the value of adminDHCP is enable(1) this value is read-only.
Changes of this value will take affect after the next switch reboot or
after … | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.266.20.2.5 |
| adminAgentNetmask The IP Netmask of the connected network.
If the value of adminDHCP is enable(1) this value is read-only.
Changes of this value will take affect after the next switch reboot or
aft… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.266.20.2.6 |
| adminAgentDhcpServerIpAddress The IP address of the last used DHCP server. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.266.20.2.7 |
| adminAgentVlanId The VLAN-ID assigned to the agent.
Changes of this value will take affect after the next switch reboot or
after setting adminReset to renewIpAndVlanParameter(5). | scalar | Integer32 | .1.3.6.1.4.1.266.20.2.8 |
| adminAgentPrioValue The IEEE802.1Q priority value and queue assigned to all frames transmitted
by the agent.
The definition between value, service class and queue are as follows:
0=Best Effort (queue… | scalar | Integer32 | .1.3.6.1.4.1.266.20.2.9 |