ntcMultiDemodCfgInputSelection
NEWTEC-MULTI-DEMOD-MIB ·
.1.3.6.1.4.1.5835.5.2.3300.1.3.1.7
Object
column
r/w
Enumeration
Toggle the demodulator input between L-BAND Rx A/B or IF Rx
Context
- MIB
- NEWTEC-MULTI-DEMOD-MIB
- OID
.1.3.6.1.4.1.5835.5.2.3300.1.3.1.7- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- ntcMultiDemodCfgEntry
- Table
- ntcMultiDemodCfgTable
- Siblings
- 18
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | lbandRxA |
1 | lbandRxB |
3 | ifRx |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ntcMultiDemodCfgDemodId The id of the demodulator | column | Enumeration | .1.3.6.1.4.1.5835.5.2.3300.1.3.1.1 |
| ntcMultiDemodCfgLnbPowerSupply LNB Power Supply and Tone selection. | column | Enumeration | .1.3.6.1.4.1.5835.5.2.3300.1.3.1.10 |
| ntcMultiDemodCfgHardwareId Demodulator hardware identification. | column | OctetString | .1.3.6.1.4.1.5835.5.2.3300.1.3.1.11 |
| ntcMultiDemodCfgModCodDvbs The selection of the FEC code-rate and modulation scheme supported by DVB-S | column | Enumeration | .1.3.6.1.4.1.5835.5.2.3300.1.3.1.12 |
| ntcMultiDemodCfgStreamMode Specify if more than one input stream is multiplexed into the modulator or
not. This sometimes impacts receiver compatibility. | column | Enumeration | .1.3.6.1.4.1.5835.5.2.3300.1.3.1.13 |
| ntcMultiDemodCfgInterfaceRate Calculated Interface Rate | column | bps SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.5835.5.2.3300.1.3.1.14 |
| ntcMultiDemodCfgAcqRange Demodulator acquisition range. Actual applied range limited to 150% of
symbolrate.. | column | Hz SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.5835.5.2.3300.1.3.1.15 |
| ntcMultiDemodCfgPlhdrScramSeq Physical layer scrambling sequence key | column | Unsigned32 | .1.3.6.1.4.1.5835.5.2.3300.1.3.1.16 |
| ntcMultiDemodCfgRfFrequency RF frequency | column | Hz OctetString | .1.3.6.1.4.1.5835.5.2.3300.1.3.1.17 |
| ntcMultiDemodCfgModCodAmcDl The selection of the FEC code-rate and modulation scheme supported by AMC-DL | column | Enumeration | .1.3.6.1.4.1.5835.5.2.3300.1.3.1.18 |
| ntcMultiDemodCfgLnbClockRef Enables or disables the transmission of a 10MHz clock signal on the LNB input
cable. | column | Enumeration | .1.3.6.1.4.1.5835.5.2.3300.1.3.1.19 |
| ntcMultiDemodCfgEnable Enable or disable the demodulator function | column | NEWTEC-TC-MIBNtcEnable | .1.3.6.1.4.1.5835.5.2.3300.1.3.1.2 |
| ntcMultiDemodCfgMode The modulation standard defines the operating mode of the demodulator.
- DVB-S : compatible with DVB-S/DVB-DSNG modulation
- DVB-S2 : compatible with EN302307
- S2 Extensions : Ne… | column | Enumeration | .1.3.6.1.4.1.5835.5.2.3300.1.3.1.3 |
| ntcMultiDemodCfgInputFrequency Demodulator input frequency setting. Current devices support a frequency range
of 950000000 to 2150000000 Hz. | column | Hz SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.5835.5.2.3300.1.3.1.4 |
| ntcMultiDemodCfgSymbolRate Symbol rate of the received carrier | column | baud SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.5835.5.2.3300.1.3.1.5 |
| ntcMultiDemodCfgRollOff The receive filter Roll-off factor setting determines the spectrum excess
bandwidth by controlling the RCRO (Root Cosine Roll-off) factor of the matched
filter at the demodulator … | column | Enumeration | .1.3.6.1.4.1.5835.5.2.3300.1.3.1.6 |
| ntcMultiDemodCfgSpectralInv Spectral inversion | column | Enumeration | .1.3.6.1.4.1.5835.5.2.3300.1.3.1.8 |
| ntcMultiDemodCfgPlScrambSig The physical layer scrambler signature. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.5835.5.2.3300.1.3.1.9 |