portDLCIBecnRecoveryCnt
NETLINK-SPECIFIC-MIB ·
.1.3.6.1.4.1.173.7.3.2.2.1.10
Object
column
mandatory
r/w
Integer32
The BECN recovery Count is a method of controlling the rate of return to max traffic flow after it has been reduced due to congestion. The value determines the number of packets received sequentially without BECN set, before increasing the Excess Burst Size by 1/8 of it's configured value.
Context
- MIB
- NETLINK-SPECIFIC-MIB
- OID
.1.3.6.1.4.1.173.7.3.2.2.1.10- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- portDLCIEntry
- Table
- portDLCIConfigTable
- Siblings
- 13
Syntax
Integer32
Values & Constraints
Object Constraints
range: 0-255
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| portDLCIRlpIndex mandatory The RLP number on which the DLCI is located. The range for
this is 1-8. | column | Integer32 | .1.3.6.1.4.1.173.7.3.2.2.1.1 |
| portDLCIPriority mandatory This field sets the priority of the DLCI among others on the
physical port. The range is 0 for lowest priority to 4 for
the highest priority. | column | Integer32 | .1.3.6.1.4.1.173.7.3.2.2.1.11 |
| portDLCIRowStatus mandatory This variable is used to manage the creation and deletion
of conceptual rows in the portDLCIConfigTable and follows the
SNMPv2 RowStatus conventions by supporting the following va… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.173.7.3.2.2.1.12 |
| portDLCIBackupGroup mandatory This object specifies (if configured as any number other than
zero) that this is a primary DLCI, and identifies the backup
DLCI(s) (in a Frame Relay backup group) that will take o… | column | Integer32 | .1.3.6.1.4.1.173.7.3.2.2.1.13 |
| portDLCIBackupProtEnb mandatory This object specifies whether the DLCI will be used as a
non-initiating backup DLCI. The DLCI will wait for a backup
protocol message from the initiating end, telling the backup
w… | column | Enumeration | .1.3.6.1.4.1.173.7.3.2.2.1.14 |
| portDLCIPortIndex mandatory The port number on which the DLCI is located. The range for
this is 1-8 for a physical FR port and 9-64 for a logical FR port. | column | Integer32 | .1.3.6.1.4.1.173.7.3.2.2.1.2 |
| portDLCIIndex mandatory The DLCI number used to identify the entry in the table. The
range is 16-991. | column | Integer32 | .1.3.6.1.4.1.173.7.3.2.2.1.3 |
| portDLCIIncomingCIR mandatory The committed information rate that is supported on the
DLCI for incoming data. | column | Integer32 | .1.3.6.1.4.1.173.7.3.2.2.1.4 |
| portDLCIOutgoingCIR mandatory The committed information rate that is supported on the
DLCI for outgoing data. | column | Integer32 | .1.3.6.1.4.1.173.7.3.2.2.1.5 |
| portDLCIIncomingBc mandatory The committed burst size is the maximum amount of data
to be transmitted under normal conditions within the time
period defined by Bc/Cir that is supported on the
DLCI for incomin… | column | Integer32 | .1.3.6.1.4.1.173.7.3.2.2.1.6 |
| portDLCIOutgoingBc mandatory The committed burst size is the maximum amount of data
to be transmitted under normal conditions within the time
period defined by Bc/Cir that is supported on the
DLCI for Outgoin… | column | Integer32 | .1.3.6.1.4.1.173.7.3.2.2.1.7 |
| portDLCIIncomingBe mandatory The excess burst size is the maximum amount of incoming data
in excess of the committed burst size that the network will try to
transfer during the time interval determined by Bc/… | column | Integer32 | .1.3.6.1.4.1.173.7.3.2.2.1.8 |
| portDLCIOutgoingBe mandatory The excess burst size is the maximum amount of incoming data
in excess of the committed burst size that the network will try to
transfer during the time interval determined by Bc/… | column | Integer32 | .1.3.6.1.4.1.173.7.3.2.2.1.9 |