itsIfSuppressAlarm
NETI-ITS-MIB ·
.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.6
Object
column
r/w
Enumeration
The alarm suppression mode. When alarms are suppressed, no
alarms will be generated if a fault situation is detected on
the interface. Failures will still be shown by the object
itsIfFailure.
notSupported(0). Suppress alarms is not supported by the
interface. This value can not be written.
none(1). No alarms are suppressed. All alarms are reported.
warning(2). Suppress alarms of severity warning only.
all(3). All alarms are suppressed. No alarms will be
reported.
Context
- MIB
- NETI-ITS-MIB
- OID
.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.6- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- itsIfEntry
- Table
- itsIfTable
- Siblings
- 18
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | notSupported |
1 | none |
2 | warning |
3 | all |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| itsIfIndex The index in the table. The index is maintained across
re-boots. The index is a positive integer value. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2928.6.2.16.1.1.2.1.1 |
| itsIfProperties Properties on the interface. A property can only be set if
the interface supports has the corresponding capability. The
capabilities of the interface can be determined by examin… | column | Bits | .1.3.6.1.4.1.2928.6.2.16.1.1.2.1.10 |
| itsIfDefects Defects indicated on the interface since the last time the
object was read.
los(0) Loss of Signal was detected.
lof(1) Loss of Frame was detected.
… | column | Bits | .1.3.6.1.4.1.2928.6.2.16.1.1.2.1.11 |
| itsIfFailure A textual string describing a fault status on the
interface. The object presents an empty string if there are
no faults on the interface. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.2928.6.2.16.1.1.2.1.12 |
| itsIfPMReference A reference to an object that presents performance data
for the interface. The object is not part of this MIB. | column | SNMPv2-TCRowPointer | .1.3.6.1.4.1.2928.6.2.16.1.1.2.1.13 |
| itsIfOperStatus The operational state of the interface. This is the same as
the object ifOperStatus in the ifTable.
up(1). The interface passes data and is used by a TTP.
… | column | Enumeration | .1.3.6.1.4.1.2928.6.2.16.1.1.2.1.14 |
| itsIfTxMuteOnFault Controls the interface output in case of a fault.
notSupported(0). The interface does not support control of
transmitter on fault. This value can only be read, and … | column | Enumeration | .1.3.6.1.4.1.2928.6.2.16.1.1.2.1.15 |
| itsIfPurpose A string presenting the purpose of the TTP that is actively
(trying) to use the interface. If no TTP is using the
interface, then the purpose is empty. If an interface can be
us… | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.2928.6.2.16.1.1.2.1.16 |
| itsIfInterfaceType Denotes the type of interface. | column | Enumeration | .1.3.6.1.4.1.2928.6.2.16.1.1.2.1.17 |
| itsIfMembersSrc A list of values of the itsSrcTtpIndex for the source trail
termination points (TTPs) that are actively connected to
this interface. A TTP can only be connected to an
interface… | column | ItsTtpIndexList | .1.3.6.1.4.1.2928.6.2.16.1.1.2.1.18 |
| itsIfMembersSnk A list of values of the itsSnkTtpIndex for the sink trail
termination points (TTPs) that are actively connected to
this interface. A TTP can only be connected to an
interface if… | column | ItsTtpIndexList | .1.3.6.1.4.1.2928.6.2.16.1.1.2.1.19 |
| itsIfIfIndex A reference to the index in the ifTable in the IF-MIB. If
this is not known, the value is 0. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2928.6.2.16.1.1.2.1.2 |
| itsIfName The textual name of the interface. The value of this object
should be the name of the interface as assigned by the local
device and should be suitable for use in commands entered … | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.2928.6.2.16.1.1.2.1.3 |
| itsIfDescr A textual string containing information about the interface.
This string should include the name of the manufacturer, the
product name and the version of the interface
hardware/so… | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.2928.6.2.16.1.1.2.1.4 |
| itsIfSpeed The interface's capacity in bits per second. This value would
be the same as presented by the object ifSpeed in the
ifTable. | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2928.6.2.16.1.1.2.1.5 |
| itsIfLoopMode Loop-back mode of the interface. When the loop-back mode is
changed to line(2) or dtm(3), a timer is initialized with the
value of itsIfLoopTime. The loop-back mode is reset to
no… | column | Enumeration | .1.3.6.1.4.1.2928.6.2.16.1.1.2.1.7 |
| itsIfLoopTime deprecated Timer for the loop-back mode. The loop-back mode is reset to
its normal mode none(0) after the specified number of
seconds. A timer value of 0 indicates infinite time, which
means… | column | Unsigned32 | .1.3.6.1.4.1.2928.6.2.16.1.1.2.1.8 |
| itsIfCapabilities Capabilities of the interface. The corresponding bit is set if
the capability is supported by the interface.
multicast(0). It is possible to use in multicast connec… | column | Bits | .1.3.6.1.4.1.2928.6.2.16.1.1.2.1.9 |