mplsLpsConfigWaitToRestore
MPLS-LPS-MIB ·
.1.3.6.1.2.1.10.166.22.1.2.1.9
Object
column
r/w
minutes Unsigned32
This object holds the Wait-to-Restore timer value in minutes
and can be configured in 1-minute intervals between 5 and
12 minutes.
The WTR timer is used to delay the reversion of the PSC state
to the Normal state when recovering from a failure condition
on the working path when the protection domain is configured
for revertive behavior.
This object may not be modified if the associated
mplsLpsConfigRowStatus object is equal to active(1).
Context
- MIB
- MPLS-LPS-MIB
- OID
.1.3.6.1.2.1.10.166.22.1.2.1.9- Type
- column
- Access
- readwrite
- Status
- current
- Units
- minutes
- Parent
- mplsLpsConfigEntry
- Table
- mplsLpsConfigTable
- Siblings
- 15
Syntax
minutes Unsigned32
Values & Constraints
Object Constraints
range: 5-12
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| mplsLpsConfigDomainIndex Index for the conceptual row identifying a protection domain.
Operators should obtain new values for row creation in this
table by reading mplsLpsConfigDomainIndexNext.
… | column | Unsigned32 | .1.3.6.1.2.1.10.166.22.1.2.1.1 |
| mplsLpsConfigHoldOff The hold-off time in deciseconds. Represents the time
between SF/SD condition detection and declaration of
an SF/SD request to the protection switching logic.
It is intended to a… | column | deciseconds Unsigned32 | .1.3.6.1.2.1.10.166.22.1.2.1.10 |
| mplsLpsConfigContinualTxInterval The Continual Tx Time in seconds. Represents the time
interval to send the continual PSC packet to the other
end, based on the current state.
This object may not b… | column | seconds Unsigned32 | .1.3.6.1.2.1.10.166.22.1.2.1.11 |
| mplsLpsConfigRapidTxInterval The Rapid Tx interval in microseconds. Represents the time
interval to send the PSC packet to the other end, when
there is a change in the state of the linear protection domain
d… | column | microseconds Unsigned32 | .1.3.6.1.2.1.10.166.22.1.2.1.12 |
| mplsLpsConfigCommand Allows the initiation of an operator command on
the protection domain.
When read, this object returns the last command written
or noCmd if no command has been writt… | column | MplsLpsCommand | .1.3.6.1.2.1.10.166.22.1.2.1.13 |
| mplsLpsConfigCreationTime The value of sysUpTime at the time the row was created. | column | SNMPv2-TCTimeStamp | .1.3.6.1.2.1.10.166.22.1.2.1.14 |
| mplsLpsConfigRowStatus This object represents the status of the MPLS-TP linear
protection domain entry. This variable is used to
create, modify, and/or delete a row in this table. | column | SNMPv2-TCRowStatus | .1.3.6.1.2.1.10.166.22.1.2.1.15 |
| mplsLpsConfigStorageType The storage type for this conceptual row.
Conceptual rows having the value 'permanent' need not
allow write access to any columnar objects in the row. | column | SNMPv2-TCStorageType | .1.3.6.1.2.1.10.166.22.1.2.1.16 |
| mplsLpsConfigDomainName Textual name that represents the MPLS-TP linear protection
domain. It facilitates easy administrative identification of
each protection domain. | column | OctetString | .1.3.6.1.2.1.10.166.22.1.2.1.2 |
| mplsLpsConfigMode The mode of the MPLS-TP linear protection mechanism. This can
be either PSC or APS, as follows:
PSC
The Protection State Coordination mode as described in
RFC 6378… | column | Enumeration | .1.3.6.1.2.1.10.166.22.1.2.1.3 |
| mplsLpsConfigProtectionType The protection architecture type of the protection domain.
This object represents both the bridge type, which can be
either a permanent bridge (1+1) or a selector bridge (1:1);
an… | column | Enumeration | .1.3.6.1.2.1.10.166.22.1.2.1.4 |
| mplsLpsConfigRevertive This object represents the reversion mode of the linear
protection domain. The reversion mode of the protection
mechanism may be either revertive or non-revertive.
… | column | Enumeration | .1.3.6.1.2.1.10.166.22.1.2.1.5 |
| mplsLpsConfigSdThreshold This object holds the threshold value of the Signal Degrade
(SD) defect in percent. In order to detect the SD defect,
the MPLS-TP packet loss measurement (LM) is performed
every … | column | Unsigned32 | .1.3.6.1.2.1.10.166.22.1.2.1.6 |
| mplsLpsConfigSdBadSeconds This object holds the number of Bad Seconds to detect the SD.
If the number of consecutive Bad Seconds reaches this value,
the SD defect is detected and used as an … | column | seconds Unsigned32 | .1.3.6.1.2.1.10.166.22.1.2.1.7 |
| mplsLpsConfigSdGoodSeconds This object holds the number of Good Seconds to declare
the clearance of an SD defect.
After an SD defect occurs on a path, if the number of
consecutive Good Second… | column | seconds Unsigned32 | .1.3.6.1.2.1.10.166.22.1.2.1.8 |