me1200AclAceTableRowEditorFilterPortList
ME1200-ACL-MIB ·
.1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.9
Object
The filter port list. It is active only when the hit action is filtered. Set the action value to 0(filter) before the new setting. Note that the action will change deny action if there is no any port in the member set. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
Context
- MIB
- ME1200-ACL-MIB
- OID
.1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.9- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- me1200AclAceTableRowEditor
- Siblings
- 85
Values & Constraints
Type Constraints
range: 8
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| me1200AclAceTableRowEditorId The identification of ACE. | scalar | Integer32 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.1 |
| me1200AclAceTableRowEditorRateLimiterId The rate limiter ID. Possible values are: 0(disabled), 1-16. | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.10 |
| me1200AclAceTableRowEditorVlanTagged The 802.1Q VLAN tagged for this ACE. | scalar | ME1200VlanTagged | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.100 |
| me1200AclAceTableRowEditorAction Action | scalar | ME1200-TCME1200RowEditorState | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.1000 |
| me1200AclAceTableRowEditorVlanId The VLAN ID for this ACE. Possible values are: 0(disabled), 1-4095. | scalar | ME1200-TCME1200Unsigned16 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.101 |
| me1200AclAceTableRowEditorVlanTagPriority The VLN tag priority for this ACE. Enable VLAN tagged filter before the
new setting. | scalar | ME1200VlanTagPriority | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.102 |
| me1200AclAceTableRowEditorEvcPolicerId The EVC policer ID. Possible values are: 0(disabled), 1-1022. | scalar | ME1200-TCME1200Unsigned16 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.11 |
| me1200AclAceTableRowEditorRedirectPortList The ingress port list for this ACE. It is active only when the hit
action is denied. Set the action value to 1(deny) before the new
setting. Set value 0 to disable the opertion. E… | scalar | ME1200-TCME1200PortList | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.12 |
| me1200AclAceTableRowEditorMirror The rmirror operation. Frames matching this ACE are mirrored to the
destination mirror port. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.13 |
| me1200AclAceTableRowEditorLogging The logging operation. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.14 |
| me1200AclAceTableRowEditorShutdown The shutdown operation. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.15 |
| me1200AclAceTableRowEditorNextAceId The next identification for this ACE. Possible values are: 0(end of
list), 1-512. | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.2 |
| me1200AclAceTableRowEditorFrameType The frame type for this ACE. | scalar | ME1200AclAceType | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.200 |
| me1200AclAceTableRowEditorLookup The second lookup operation for this ACE. Possible values are:
1(enabled) and 2(disabled). | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.3 |
| me1200AclAceTableRowEditorEtypeSrcMacOp Indicates how a Ethernet type packet's source MAC address is to be
compared. This object can only be configured if FrameType is etype(1). | scalar | ME1200ASType | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.300 |
| me1200AclAceTableRowEditorEtypeSrcMac Indicates the 48 bits source MAC address. This object can only be
configured if FrameType is etype(1) and EtypeSrcMacOp is specific(1). | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.301 |
| me1200AclAceTableRowEditorEtypeDestMacOp Indicates how a Ethernet type packet's destination MAC address is to be
compared. This object can only be configured if FrameType is etype(1). | scalar | ME1200AdvDestMacType | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.302 |
| me1200AclAceTableRowEditorEtypeDestMac Indicates the 48 bits destination MAC address. This object can only be
configured if FrameType is etype(1) and EtypeDestMacOp is specific(1). | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.303 |
| me1200AclAceTableRowEditorEtype Indicates the packet's 16 bit Ethernet type field. Possible values are:
0(disabled), 0x600-0xFFFF but excluding 0x800(IPv4), 0x806(ARP) and
0x86DD(IPv6).This object can only be co… | scalar | ME1200-TCME1200Unsigned16 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.304 |
| me1200AclAceTableRowEditorIngressPortList The ingress port list for this ACE. Each octet within this value
specifies a set of eight ports, with the first octet specifying ports 1
through 8, the second octet specifying por… | scalar | ME1200-TCME1200PortList | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.5 |
| me1200AclAceTableRowEditorPolicyValue The policy number for this ACE. The feature is inactive when policy
mask value is non-zero. | scalar | ME1200-TCME1200Unsigned8 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.6 |
| me1200AclAceTableRowEditorArpSrcMacOp Indicates how a ARP packet's source MAC address is to be compared. This
object can only be configured if FrameType is arp(4). | scalar | ME1200ASType | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.600 |
| me1200AclAceTableRowEditorArpSrcMac Indicates the 48 bits source MAC address. This object can only be
configured if FrameType is arp(4) and ArpSrcMacOp is specific(1). | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.601 |
| me1200AclAceTableRowEditorArpDestMacOp Indicates how a ARP packet's destination MAC address is to be compared.
This object can only be configured if FrameType is arp(4). | scalar | ME1200DestMacType | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.602 |
| me1200AclAceTableRowEditorArpSenderIp The specified ARP sender IP address. The packets sender address is
AND-ed with the value of ArpSenderIpMask and then compared with the
value of this object. If ArpSenderIp and Arp… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.603 |
| me1200AclAceTableRowEditorArpSenderIpMask The specified ARP sender IP address mask. This object can only be
configured if FrameType is arp(4). | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.604 |
| me1200AclAceTableRowEditorArpTragetIp The specified ARP target IP address. The packets target address is
AND-ed with the value of ArpTragetIpMask and then compared with the
value of this object. If ArpTragetIp and Arp… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.605 |
| me1200AclAceTableRowEditorArpTragetIpMask The specified ARP target IP address mask. This object can only be
configured if FrameType is arp(4). | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.606 |
| me1200AclAceTableRowEditorArpOpcode Indicates how a ARP packet's opcode is to be compared. This object can
only be configured if FrameType is arp(4). | scalar | ME1200ArpOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.607 |
| me1200AclAceTableRowEditorArpFlagRequest Indicates how a ARP packet's request/reply opcode is to be compared.
The value 0 means any ARP opcode is allowed (don't-care field), value 1
means ARP opcode is equal to request o… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.608 |
| me1200AclAceTableRowEditorArpFlagSenderMac Indicates how a ARP packet's sender hardware address field (SHA) is to
be compared. The value 0 means any SHA value is allowed (don't-care
field), value 1 means SHA is not equal t… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.609 |
| me1200AclAceTableRowEditorArpFlagTargetMac Indicates how a ARP packet's target hardware address field (THA) is to
be compared. The value 0 means any THA value is allowed (don't-care
field), value 1 means THA is not equal t… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.610 |
| me1200AclAceTableRowEditorArpFlagLen Indicates how a ARP packet's s hardware address length field (HLN) is
to be compared. The value 0 means any HLN value is allowed (don't-care
field), value 1 means HLN is not equal… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.611 |
| me1200AclAceTableRowEditorArpFlagIp Indicates how a ARP packet's hardware address space field (HRD) is to
be compared. The value 0 means any HRD value is allowed (don't-care
field), value 1 means HRD is not equal to… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.612 |
| me1200AclAceTableRowEditorArpFlagEthernet Indicates how a ARP packet's protocol address space field (PRO) is to
be compared. The value 0 means any PRO value is allowed (don't-care
field), value 1 means PRO is not equal to… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.613 |
| me1200AclAceTableRowEditorPolicyMask The policy number for this ACE. The feature is inactive when policy
mask value is non-zero. | scalar | ME1200-TCME1200Unsigned8 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.7 |
| me1200AclAceTableRowEditorIpv4DestMacOp Indicates how a IPv4 packet's destination MAC address is to be
compared. This object can only be configured if FrameType is ipv4(5). | scalar | ME1200DestMacType | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.700 |
| me1200AclAceTableRowEditorIpv4ProtocolOp Indicates how a IPv4 packet's protocol field is to be compared. This
object can only be configured if FrameType is ipv4(5). | scalar | ME1200ASType | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.701 |
| me1200AclAceTableRowEditorIpv4Protocol The protocol number field in the IPv4 header used to indicate a higher
layer protocol. Possible values are 0-255.This object can only be
configured if FrameType is ipv4(5) and Ipv… | scalar | ME1200-TCME1200Unsigned8 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.702 |
| me1200AclAceTableRowEditorIpv4FlagTtl Indicates how a IPv4 packet's Time-to-Live field (TTL) is to be
compared. The value 0 means any TTL value is allowed (don't-care
field), value 1 means TTL is not equal zero and va… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.703 |
| me1200AclAceTableRowEditorIpv4FlagFragment Indicates how a IPv4 packet's More-Fragments field (MF) is to be
compared. The value 0 means any MF value is allowed (don't-care field),
value 1 means MF is not equal one (MF fiel… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.704 |
| me1200AclAceTableRowEditorIpv4FlagIpOption Indicates how a IPv4 packet's options field is to be compared. The
value 0 means any options is allowed (don't-care field), value 1 means
options is not equal one (options field i… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.705 |
| me1200AclAceTableRowEditorIpv4SrcIp The specified source IPv4 address. The packets sender address is AND-ed
with the value of Ipv4SrcIpMask and then compared with the value of
this object. If Ipv4SrcIp and Ipv4SrcIp… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.706 |
| me1200AclAceTableRowEditorIpv4SrcIpMask The specified source IPv4 address mask. This object can only be
configured if FrameType isipv4(5). | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.707 |
| me1200AclAceTableRowEditorIpv4DestIp The specified destination IPv4 address. The packets sender address is
AND-ed with the value of Ipv4DestIpMask and then compared with the
value of this object. If Ipv4DestIp and Ip… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.708 |
| me1200AclAceTableRowEditorIpv4DestIpMask The specified destination IPv4 address mask. This object can only be
configured if FrameType isipv4(5). | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.709 |
| me1200AclAceTableRowEditorIpv4IcmpTypeOp Indicates how a IPv4 packet's ICMP type field is to be compared. This
object can only be configured if FrameType is ipv4(5) and Ipv4Protocol
is icmp(1). | scalar | ME1200ASType | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.710 |
| me1200AclAceTableRowEditorIpv4IcmpType The ICMP type field in the IPv4 header. Possible values are 0-255.This
object can only be configured if FrameType is ipv4(5), Ipv4Protocol is
icmp(1) and Ipv4IcmpTypeOp is specifi… | scalar | ME1200-TCME1200Unsigned8 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.711 |
| me1200AclAceTableRowEditorIpv4IcmpCodeOp Indicates how a IPv4 packet's ICMP code field is to be compared. This
object can only be configured if FrameType is ipv4(5) and Ipv4Protocol
is icmp(1). | scalar | ME1200ASType | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.712 |
| me1200AclAceTableRowEditorIpv4IcmpCode The ICMP code field in the IPv4 header. Possible values are 0-255.This
object can only be configured if FrameType is ipv4(5), Ipv4Protocol is
icmp(1) and Ipv4IcmpCodeOp is specifi… | scalar | ME1200-TCME1200Unsigned8 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.713 |
| me1200AclAceTableRowEditorIpv4SrcPortOp Indicates how a packet's source TCP/UDP port number is to be compared.
This object can only be configured if FrameType is ipv4(5). | scalar | ME1200ASRType | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.714 |
| me1200AclAceTableRowEditorIpv4SrcPort The source port number of the TCP or UDP protocol. If the Ipv4SrcPortOp
object in the same row is range(2), this object will be the starting
port number of the port range. Valid r… | scalar | ME1200-TCME1200Unsigned16 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.715 |
| me1200AclAceTableRowEditorIpv4SrcPortRange The source port number of the TCP or UDP protocol. If the Ipv4SrcPortOp
object in the same row is range(2), this object will be the ending port
number of the port range. Valid ran… | scalar | ME1200-TCME1200Unsigned16 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.716 |
| me1200AclAceTableRowEditorIpv4DestPortOp Indicates how a packet's destination TCP/UDP port number is to be
compared. This object can only be configured if FrameType is ipv4(5). | scalar | ME1200ASRType | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.717 |
| me1200AclAceTableRowEditorIpv4DestPort The destination port number of the TCP or UDP protocol. If the
Ipv4DestPortOp object in the same row is range(2), this object will be
the starting port number of the port range. V… | scalar | ME1200-TCME1200Unsigned16 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.718 |
| me1200AclAceTableRowEditorIpv4DestPortRange The destination port number of the TCP or UDP protocol. If the
Ipv4DestPortOp object in the same row is range(2), this object will be
the ending port number of the port range. Val… | scalar | ME1200-TCME1200Unsigned16 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.719 |
| me1200AclAceTableRowEditorIpv4TcpFlagFin Indicates how a IPv4 TCP packet's 'No more data from sender' field
(FIN) is to be compared. The value 0 means any FIN value is allowed
(don't-care field), value 1 means FIN is not… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.720 |
| me1200AclAceTableRowEditorIpv4TcpFlagSyn Indicates how a IPv4 TCP packet's 'Synchronize sequence numbers' field
(SYN) is to be compared. The value 0 means any SYN value is allowed
(don't-care field), value 1 means SYN is… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.721 |
| me1200AclAceTableRowEditorIpv4TcpFlagRst Indicates how a IPv4 TCP packet's 'Reset the connection' field (RST) is
to be compared. The value 0 means any RST value is allowed (don't-care
field), value 1 means RST is not equ… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.722 |
| me1200AclAceTableRowEditorIpv4TcpFlagPsh Indicates how a IPv4 TCP packet's 'Push Function' field (PSH) is to be
compared. The value 0 means any PSH value is allowed (don't-care
field), value 1 means PSH is not equal one … | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.723 |
| me1200AclAceTableRowEditorIpv4TcpFlagAck Indicates how a IPv4 TCP packet's 'Acknowledgment field significant'
field (ACK) is to be compared. The value 0 means any FIN value is
allowed (don't-care field), value 1 means AC… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.724 |
| me1200AclAceTableRowEditorIpv4TcpFlagUrg Indicates how a IPv4 TCP packet's 'Urgent Pointer field significant'
field (URG) is to be compared. The value 0 means any URG value is
allowed (don't-care field), value 1 means UR… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.725 |
| me1200AclAceTableRowEditorHitAction The hit action operation for this ACE. Note all ports will be the
filter port member when filter action is set on the first time. | scalar | ME1200AclAceHitAction | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.8 |
| me1200AclAceTableRowEditorIPv6DestMacOp Indicates how a IPv6 packet's destination MAC address is to be
compared. This object can only be configured if FrameType is arp(4). | scalar | ME1200DestMacType | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.800 |
| me1200AclAceTableRowEditorIpv6NextHeaderOp Indicates how a IPv6 packet's next header field is to be compared. This
object can only be configured if FrameType is ipv6(6). | scalar | ME1200ASType | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.801 |
| me1200AclAceTableRowEditorIpv6NextHeader The next header field in the IPv6 header used to indicate a higher
layer protocol. Possible values are 0-255.This object can only be
configured if FrameType is ipv6(6) and Ipv6Nex… | scalar | ME1200-TCME1200Unsigned8 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.802 |
| me1200AclAceTableRowEditorIpv6SrcIp The specified IPv6 source address. The packets source address is AND-ed
with the value of Ipv6SrcIpMask and then compared with the value of
this object. If Ipv6SrcIp and Ipv6SrcIp… | scalar | INET-ADDRESS-MIBInetAddressIPv6 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.803 |
| me1200AclAceTableRowEditorIpv6SrcIpMask The specified IPv6 source address mask. Only the least significant 32
bits of this object are used. This object can only be configured if
FrameType is ipv6(6). | scalar | INET-ADDRESS-MIBInetAddressIPv6 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.804 |
| me1200AclAceTableRowEditorIpv6FlagHopLimiter Indicates how a IPv6 packet's hop limit field is to be compared. The
value 0 means any hop limit value is allowed (don't-care field), value
1 means hop limit is not equal zero and… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.805 |
| me1200AclAceTableRowEditorIpv6Icmpv6TypeOp Indicates how a IPv6 packet's ICMPv6 type field is to be compared. This
object can only be configured if FrameType is ipv6(6) and
Ipv6NextHeader is icmpv6(58). | scalar | ME1200ASType | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.806 |
| me1200AclAceTableRowEditorIpv6Icmpv6Type The ICMPv6 type field in the IPv6 header. Possible values are
0-255.This object can only be configured if FrameType is ipv6(6),
Ipv6NextHeader is icmpv6(58) and Ipv6Icmpv6TypeOp i… | scalar | ME1200-TCME1200Unsigned8 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.807 |
| me1200AclAceTableRowEditorIpv6Icmpv6CodeOp Indicates how a IPv6 packet's ICMPv6 code field is to be compared. This
object can only be configured if FrameType is ipv6(6) and
Ipv6NextHeader is icmpv6(58). | scalar | ME1200ASType | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.808 |
| me1200AclAceTableRowEditorIpv6Icmpv6Code The ICMPv6 code field in the IPv6 header. Possible values are
0-255.This object can only be configured if FrameType is ipv6(6),
Ipv6NextHeader is icmpv6(58) and Ipv6Icmpv6CodeOp i… | scalar | ME1200-TCME1200Unsigned8 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.809 |
| me1200AclAceTableRowEditorIpv6SrcPortOp Indicates how a packet's source TCP/UDP port number is to be compared.
This object can only be configured if FrameType is ipv6(6). | scalar | ME1200ASRType | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.810 |
| me1200AclAceTableRowEditorIpv6SrcPort The source port number of the TCP or UDP protocol. If the Ipv6SrcPortOp
object in the same row is range(2), this object will be the starting
port number of the port range. Valid r… | scalar | ME1200-TCME1200Unsigned16 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.811 |
| me1200AclAceTableRowEditorIpv6SrcPortRange The source port number of the TCP or UDP protocol. If the Ipv6SrcPortOp
object in the same row is range(2), this object will be the ending port
number of the port range. Valid ran… | scalar | ME1200-TCME1200Unsigned16 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.812 |
| me1200AclAceTableRowEditorIpv6DestPortOp Indicates how a packet's destination TCP/UDP port number is to be
compared. This object can only be configured if FrameType is ipv6(6). | scalar | ME1200ASRType | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.813 |
| me1200AclAceTableRowEditorIpv6DestPort The destination port number of the TCP or UDP protocol. If the
Ipv6DestPortOp object in the same row is range(2), this object will be
the starting port number of the port range. V… | scalar | ME1200-TCME1200Unsigned16 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.814 |
| me1200AclAceTableRowEditorIpv6DestPortRange The destination port number of the TCP or UDP protocol. If the
Ipv6DestPortOp object in the same row is range(2), this object will be
the ending port number of the port range. Val… | scalar | ME1200-TCME1200Unsigned16 | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.815 |
| me1200AclAceTableRowEditorIpv6TcpFlagFin Indicates how a IPv6 TCP packet's 'No more data from sender' field
(FIN) is to be compared. The value 0 means any FIN value is allowed
(don't-care field), value 1 means FIN is not… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.816 |
| me1200AclAceTableRowEditorIpv6TcpFlagSyn Indicates how a IPv6 TCP packet's 'Synchronize sequence numbers' field
(SYN) is to be compared. The value 0 means any SYN value is allowed
(don't-care field), value 1 means SYN is… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.817 |
| me1200AclAceTableRowEditorIpv6TcpFlagRst Indicates how a IPv6 TCP packet's 'Reset the connection' field (RST) is
to be compared. The value 0 means any RST value is allowed (don't-care
field), value 1 means RST is not equ… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.818 |
| me1200AclAceTableRowEditorIpv6TcpFlagPsh Indicates how a IPv6 TCP packet's 'Push Function' field (PSH) is to be
compared. The value 0 means any PSH value is allowed (don't-care
field), value 1 means PSH is not equal one … | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.819 |
| me1200AclAceTableRowEditorIpv6TcpFlagAck Indicates how a IPv6 TCP packet's 'Acknowledgment field significant'
field (ACK) is to be compared. The value 0 means any FIN value is
allowed (don't-care field), value 1 means AC… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.820 |
| me1200AclAceTableRowEditorIpv6TcpFlagUrg Indicates how a IPv6 TCP packet's 'Urgent Pointer field significant'
field (URG) is to be compared. The value 0 means any URG value is
allowed (don't-care field), value 1 means UR… | scalar | ME1200AclAceFlagOpcode | .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.821 |