softwareCommandOperation
LUM-SOFTWARE-MIB ·
.1.3.6.1.4.1.8708.2.28.2.3.6
Object
scalar
r/w
Enumeration
The operation to perform.
test - A no operation - test semaphore.
Optional use.
check - do not install anything, just show what needs
to be done.
install - install but do not activate.
upgrade - install and activate
rebootAfter - install, activate and reboot.
This should not be used by SNMP.
rebootCu - reboot the main CU.
rebootAll - reboot all boards.
revert - 'Undo' an upgrade operation and set the
'next' to be the same as 'executing'.
This has to be done before reboot.
Revert does not work if the file system has
been upgraded.
abort - release the transaction.
unlock - release the transaction.
clean - prepare space by cleaning (FTP)
forcedUnlock - node internal operation.
Release transaction without passwd.
rebootAllCode - reboot all Cold.
rebootExpr - reboot card(s) specified by the subrack slot expr.
rebootCold - cold reboot of card(s) specified by the subrack slot expr.
rebootPendingBoards - Only boards that have activated new software are rebooted.
If the activated software is already running,
the board is not rebooted.
Context
- MIB
- LUM-SOFTWARE-MIB
- OID
.1.3.6.1.4.1.8708.2.28.2.3.6- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- softwareCommand
- Siblings
- 24
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | test |
2 | check |
3 | install |
4 | upgrade |
5 | rebootAfter |
6 | rebootCu |
7 | rebootAll |
8 | revert |
9 | abort |
10 | unlock |
11 | clean |
12 | forcedUnlock |
13 | rebootAllCold |
14 | rebootExpr |
15 | rebootCold |
16 | rebootPendingBoards |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| softwareCommandServerIp The IP address of the host to retrieve the file from. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.8708.2.28.2.3.1 |
| softwareCommandOperationState State to show the progress of the operation.
idle - when no operation is in progress.
pending - operation is ordered but will start later
… | scalar | Enumeration | .1.3.6.1.4.1.8708.2.28.2.3.10 |
| softwareCommandProgressMax Show the maximum value of the progressCounter | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.28.2.3.11 |
| softwareCommandResult The result of the operation
none - no result
success - the latest operation was successful.
failed - the latest operation failed. | scalar | Enumeration | .1.3.6.1.4.1.8708.2.28.2.3.12 |
| softwareCommandEnmState Only applicable if result != none.
none - no state
upToDate - no upgrade needed
rebootNeeded … | scalar | Enumeration | .1.3.6.1.4.1.8708.2.28.2.3.13 |
| softwareCommandErrorCount Shows the number of minor erros encountered. | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.28.2.3.14 |
| softwareCommandProgressCounter Shows the progress of the ongoing
ENM upgrade. | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.28.2.3.15 |
| softwareCommandNewPassword This is a secret, write-only, parameter.
This is set in the same multi-set as testAndIncr
and will be used as the client password to the
transaction.
It must… | scalar | Unsigned32 | .1.3.6.1.4.1.8708.2.28.2.3.16 |
| softwareCommandPassword This is a secret, write-only, parameter.
This parameter will trigger the operation.
Use the same value as set in newPasswd. | scalar | Unsigned32 | .1.3.6.1.4.1.8708.2.28.2.3.17 |
| softwareCommandReleaseAfterOperation Release lock after operation. | scalar | Enumeration | .1.3.6.1.4.1.8708.2.28.2.3.18 |
| softwareCommandSendTraps Set this to indicate whether you want traps or not. | scalar | Enumeration | .1.3.6.1.4.1.8708.2.28.2.3.19 |
| softwareCommandEnmFile Full path to the ENM-spec to use. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.28.2.3.2 |
| softwareCommandClientOperationId This value is set by the SNMP client
for each operation. The value is
sent back in the traps generated
by the operation. | scalar | Unsigned32 | .1.3.6.1.4.1.8708.2.28.2.3.20 |
| softwareCommandTftpTimeout This parameter stipulates the timeout
used by TFTP when downloading from
the network.
Normally, you do not have to use this!
If the circumstances are extreme… | scalar | Unsigned32 | .1.3.6.1.4.1.8708.2.28.2.3.21 |
| softwareCommandLocalFtpDirectory Full path to the directory where files
should be FTPd from TNM. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.28.2.3.22 |
| softwareCommandWarningCount Shows the number of warnings encountered. | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.28.2.3.23 |
| softwareCommandEnmRelease The current ENM release. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.28.2.3.24 |
| softwareCommandSubrackSlotExpr The subrack and slot expression to perform action on
If value is empty, 'all' is assumed.
Expression follows mibsh swu command, accepting '<subrack> <slot>'
… | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.28.2.3.25 |
| softwareCommandIncludeFs Shall the file system be included in the operation? | scalar | Enumeration | .1.3.6.1.4.1.8708.2.28.2.3.3 |
| softwareCommandCleanFirst Shall the file system be 'cleaned' before the operation?
noClean - do not clean
normalClean - equivalent to 'swu clean all all'
culessClean - this will also remo… | scalar | Enumeration | .1.3.6.1.4.1.8708.2.28.2.3.4 |
| softwareCommandForce Ignore minor failures. | scalar | Enumeration | .1.3.6.1.4.1.8708.2.28.2.3.5 |
| softwareCommandOperationTimeout Delay (in seconds) until the operation is started. | scalar | Unsigned32 | .1.3.6.1.4.1.8708.2.28.2.3.7 |
| softwareCommandTestAndIncr Protection against simultaneous access from
multiple managers. See SNMPv2-TC.
Setting this variable implies that a transaction
starts. The provided newPasswd will be se… | scalar | SNMPv2-TCTestAndIncr | .1.3.6.1.4.1.8708.2.28.2.3.8 |
| softwareCommandSemaphore The primary state of the SWU-server
NOTE that this variable will change state without
affecting the lastChange time stamp.
Test this variable before starting… | scalar | Enumeration | .1.3.6.1.4.1.8708.2.28.2.3.9 |