softwareCommandEnmState
LUM-SOFTWARE-MIB ·
.1.3.6.1.4.1.8708.2.28.2.3.13
Object
scalar
Enumeration
Only applicable if result != none.
none - no state
upToDate - no upgrade needed
rebootNeeded - all software is activated, but reboot of
some boards are required
activateNeeded - all software is installed, but activation of
new software required
upgradeNeeded - installation of new software required
done - the new software is installed and activated,
and, the updated board are rebooted.
filesNeeded - Software for all boards currently installed
in the node is up to date. filesNeeded
indicates that a software download might be
needed for a board that is added or
replaced.
upgradeWithoutRebootNeeded - This state shows that the node already runs on
on the software stated in enm-spec. To update
the enm-spec although, an upgrade without reboot
is needed.
removeBoardNeeded - This state shows that the node contains a board
that is too old to upgrade. The board must be
removed.
Context
- MIB
- LUM-SOFTWARE-MIB
- OID
.1.3.6.1.4.1.8708.2.28.2.3.13- Type
- scalar
- Access
- readonly
- Status
- current
- Parent
- softwareCommand
- Siblings
- 24
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | none |
2 | upToDate |
3 | rebootNeeded |
4 | activateNeeded |
5 | upgradeNeeded |
6 | done |
7 | filesNeeded |
8 | upgradeWithoutRebootNeeded |
9 | removeBoardNeeded |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| softwareCommandServerIp The IP address of the host to retrieve the file from. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.8708.2.28.2.3.1 |
| softwareCommandOperationState State to show the progress of the operation.
idle - when no operation is in progress.
pending - operation is ordered but will start later
… | scalar | Enumeration | .1.3.6.1.4.1.8708.2.28.2.3.10 |
| softwareCommandProgressMax Show the maximum value of the progressCounter | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.28.2.3.11 |
| softwareCommandResult The result of the operation
none - no result
success - the latest operation was successful.
failed - the latest operation failed. | scalar | Enumeration | .1.3.6.1.4.1.8708.2.28.2.3.12 |
| softwareCommandErrorCount Shows the number of minor erros encountered. | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.28.2.3.14 |
| softwareCommandProgressCounter Shows the progress of the ongoing
ENM upgrade. | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.28.2.3.15 |
| softwareCommandNewPassword This is a secret, write-only, parameter.
This is set in the same multi-set as testAndIncr
and will be used as the client password to the
transaction.
It must… | scalar | Unsigned32 | .1.3.6.1.4.1.8708.2.28.2.3.16 |
| softwareCommandPassword This is a secret, write-only, parameter.
This parameter will trigger the operation.
Use the same value as set in newPasswd. | scalar | Unsigned32 | .1.3.6.1.4.1.8708.2.28.2.3.17 |
| softwareCommandReleaseAfterOperation Release lock after operation. | scalar | Enumeration | .1.3.6.1.4.1.8708.2.28.2.3.18 |
| softwareCommandSendTraps Set this to indicate whether you want traps or not. | scalar | Enumeration | .1.3.6.1.4.1.8708.2.28.2.3.19 |
| softwareCommandEnmFile Full path to the ENM-spec to use. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.28.2.3.2 |
| softwareCommandClientOperationId This value is set by the SNMP client
for each operation. The value is
sent back in the traps generated
by the operation. | scalar | Unsigned32 | .1.3.6.1.4.1.8708.2.28.2.3.20 |
| softwareCommandTftpTimeout This parameter stipulates the timeout
used by TFTP when downloading from
the network.
Normally, you do not have to use this!
If the circumstances are extreme… | scalar | Unsigned32 | .1.3.6.1.4.1.8708.2.28.2.3.21 |
| softwareCommandLocalFtpDirectory Full path to the directory where files
should be FTPd from TNM. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.28.2.3.22 |
| softwareCommandWarningCount Shows the number of warnings encountered. | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.28.2.3.23 |
| softwareCommandEnmRelease The current ENM release. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.28.2.3.24 |
| softwareCommandSubrackSlotExpr The subrack and slot expression to perform action on
If value is empty, 'all' is assumed.
Expression follows mibsh swu command, accepting '<subrack> <slot>'
… | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.28.2.3.25 |
| softwareCommandIncludeFs Shall the file system be included in the operation? | scalar | Enumeration | .1.3.6.1.4.1.8708.2.28.2.3.3 |
| softwareCommandCleanFirst Shall the file system be 'cleaned' before the operation?
noClean - do not clean
normalClean - equivalent to 'swu clean all all'
culessClean - this will also remo… | scalar | Enumeration | .1.3.6.1.4.1.8708.2.28.2.3.4 |
| softwareCommandForce Ignore minor failures. | scalar | Enumeration | .1.3.6.1.4.1.8708.2.28.2.3.5 |
| softwareCommandOperation The operation to perform.
test - A no operation - test semaphore.
Optional use.
check - do not install anything, just show what needs
to be … | scalar | Enumeration | .1.3.6.1.4.1.8708.2.28.2.3.6 |
| softwareCommandOperationTimeout Delay (in seconds) until the operation is started. | scalar | Unsigned32 | .1.3.6.1.4.1.8708.2.28.2.3.7 |
| softwareCommandTestAndIncr Protection against simultaneous access from
multiple managers. See SNMPv2-TC.
Setting this variable implies that a transaction
starts. The provided newPasswd will be se… | scalar | SNMPv2-TCTestAndIncr | .1.3.6.1.4.1.8708.2.28.2.3.8 |
| softwareCommandSemaphore The primary state of the SWU-server
NOTE that this variable will change state without
affecting the lastChange time stamp.
Test this variable before starting… | scalar | Enumeration | .1.3.6.1.4.1.8708.2.28.2.3.9 |