mrtIfHighSpeed
LUM-MULTIRATE-MIB ·
.1.3.6.1.4.1.8708.2.12.2.2.1.1.10
Object
column
r/w
Unsigned32
The expected signal bit rate in units of 1,000,000 bits (Mb) per second. If this object reports a value of 'n' then the speed of the interface is somewhere in the range of 'n-500,000' to 'n+499,999'.
Context
- MIB
- LUM-MULTIRATE-MIB
- OID
.1.3.6.1.4.1.8708.2.12.2.2.1.1.10- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- mrtIfEntry
- Table
- mrtIfTable
- Siblings
- 74
Syntax
Unsigned32
Values & Constraints
Object Constraints
range: 125-2500
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| mrtIfIndex An arbitrary index assigned to each entry. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.12.2.2.1.1.1 |
| mrtIfHighSpeedMin The minmum speed in units of 1,000,000 bits (Mb)
per second. If this object reports a value of 'n'
then the speed of the interface is somewhere in
the range of 'n-500,000' to 'n+4… | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.8708.2.12.2.2.1.1.11 |
| mrtIfHighSpeedMax The maximum speed in units of 1,000,000 bits per
second. If this object reports a value of 'n'
then the speed of the interface is somewhere in
the range of 'n-500,000' to 'n+499,9… | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.8708.2.12.2.2.1.1.12 |
| mrtIfPowerLevel The received power level in units of 0.1 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.12.2.2.1.1.13 |
| mrtIfPowerLevelHighThreshold The upper threshold for received power level in
units of 0.1 dBm.
Note: Depending on the type of board and interface
the value range may vary. The 'stm4' and 'stm1'… | column | Integer32 | .1.3.6.1.4.1.8708.2.12.2.2.1.1.14 |
| mrtIfPowerLevelLowThreshold The lower threshold for received power level in
units of 0.1 dBm.
Note: Depending on the type of board and interface
the value range may vary. The 'stm4' and 'stm1'… | column | Integer32 | .1.3.6.1.4.1.8708.2.12.2.2.1.1.15 |
| mrtIfLaserStatus The operational state of the laser.
off - The laser is turned off.
on - The laser is turned on. | column | Enumeration | .1.3.6.1.4.1.8708.2.12.2.2.1.1.16 |
| mrtIfAdminStatus The administrative state for the interface.
down - The interface should be inactive.
service - The interface is activated but alarms
are suppressed. … | column | LUM-TCBoardOrInterfaceAdminStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.17 |
| mrtIfOperStatus The operational state for the interface.
notPresent - The physical resources are not
available.
down - The interface is de-activated or the are
fault… | column | LUM-TCBoardOrInterfaceOperStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.18 |
| mrtIfLossOfSignal Loss of signal.
Applicable for all signal formats.
A(ctivation): Active loss of signal HW
indication.
D(e-activation): Inactive loss of signal HW
ind… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.19 |
| mrtIfName The management name of the interface, for
example 'mrti1:2:1', where the first number
indicates sub-rack, the second slot number and
the third is the port number.
Examples:
… | column | LUM-TCMgmtNameString | .1.3.6.1.4.1.8708.2.12.2.2.1.1.2 |
| mrtIfReceivedPowerHigh Received power level is too high.
Applicable for all signal formats.
A: The received power level exceeds the
the built-in overload threshold.
D: The … | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.20 |
| mrtIfReceivedPowerLow Received power level low threshold exceeded.
Applicable for all signal formats.
A: The received power level is below the
associated threshold.
D: The… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.21 |
| mrtIfLaserBiasHigh Laser bias high threshold exceeded.
A: The laser bias current exceeds the
associated threshold.
D: The laser bias current is 0.5 mA below the
associa… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.22 |
| mrtIfErroredSeconds deprecated Note: This attribute is deprecated!
Errored seconds threshold exceeded.
A: The number of errored seconds (ES) during a
period exceeds the associated … | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.23 |
| mrtIfSeverelyErroredSeconds deprecated Note: This attribute is deprecated!
Severely errored seconds (SES) threshold exceeded.
A: The number of severely errored seconds during a period
exce… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.24 |
| mrtIfBackgroundBlockErrors deprecated Note: This attribute is deprecated!
Background block errors (BBE) threshold exceeded.
A: The number of errors during a period
exceeds the associated … | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.25 |
| mrtIfUnavailableSeconds deprecated Note: This attribute is deprecated!
Unavailable seconds (UAS) threshold exceeded.
A: The number of unavailable seconds during a period
exceeds the as… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.26 |
| mrtIfLossOfFrame Loss of frame.
Applicable for SDH/Sonet signal formats.
A: SDH frame can not be located.
D: SDH frame is located. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.27 |
| mrtIfMsAlarmIndicationSignalC2W MS Alarm indication signal (MS-AIS) on the
client side.
Applicable for SDH/Sonet signal formats.
A: An 'all ones' SDH signal is detected.
D: SDH sign… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.28 |
| mrtIfRemoteDefectIndication Remote defect indication.
Applicable for SDH/Sonet signal formats.
A: RDI indication (in SDH frame) active.
D: RDI indication inactive. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.29 |
| mrtIfDescr User configurable label.
This attribute can be written via SNMP. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.12.2.2.1.1.3 |
| mrtIfLossOfSync Loss of sync (GbE).
Applicable for GbE signal formats.
A: GbE 'frame' can not be located.
D: GbE 'frame' is located. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.30 |
| mrtIfBitrateMismatch Bitrate mismatch (Other).
Applicable for other signal formats.
D: The interface is unable to lock to the
inserted signal.
D: The interface is able to… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.31 |
| mrtIfLaserBias Measures laser bias current value in tenths of
mA (0.1 mA). | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.12.2.2.1.1.32 |
| mrtIfLaserBiasThreshold Sets the threshold for the laser bias alarm.
in percentage relative to the value set during
production.
The preset value is 100%. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.12.2.2.1.1.33 |
| mrtIfJ0PathTrace The recevied J0 path trace string.
Applicable for SDH/Sonet signal formats. | column | OctetString | .1.3.6.1.4.1.8708.2.12.2.2.1.1.34 |
| mrtIfAuAlarmIndicationSignalW2C Alarm indication signal (AIS) on the trunk-side.
Applicable for SDH/Sonet signal formats.
A: An 'all ones' SDH signal is detected.
D: SDH signal reco… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.35 |
| mrtIfAuLossOfPointerW2C Loss of pointer detected on the trunk-side.
Applicable for SDH/Sonet signal formats.
A: A loss of pointer is detected.
D: SDH signal recovered. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.36 |
| mrtIfTxSignalStatus The operational state for outgoing (TX) signal
of the interface.
down - A fault that would lead to a protection
switch has occurred.
degraded - The s… | column | Enumeration | .1.3.6.1.4.1.8708.2.12.2.2.1.1.37 |
| mrtIfTruncVc4 States which VC4 in the STM-16 frame that the
interface is connected to.
0 means unconnected, i.e. the signal passes
through. (This may cause a loop depending on
… | column | Unsigned32 | .1.3.6.1.4.1.8708.2.12.2.2.1.1.38 |
| mrtIfAuAlarmIndicationSignalC2W Alarm indication signal (AIS) on the
client-side.
Applicable for SDH/Sonet signal formats.
A: An 'all ones' SDH signal is detected.
D: SDH signal rec… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.39 |
| mrtIfSubrack The number of the subrack where the interface
is located. | column | LUM-TCSubrackNumber | .1.3.6.1.4.1.8708.2.12.2.2.1.1.4 |
| mrtIfAuLossOfPointerC2W Loss of pointer detected on the client-side.
Applicable for SDH/Sonet signal formats.
A: A loss of pointer is detected.
D: SDH signal recovered. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.40 |
| mrtIfTraceIntrusionMode Indicates wether the trace identifier should be
inserted in the transmitted signal.
disabled - The trace identifier is taken from
the recevied signal if possible.
… | column | Enumeration | .1.3.6.1.4.1.8708.2.12.2.2.1.1.41 |
| mrtIfTraceTransmitted The trace identifier to be transmitted from this
interface.
Set to empty string for default value:
<IP address>:<subrack>:<slot>:<port>
… | column | OctetString | .1.3.6.1.4.1.8708.2.12.2.2.1.1.42 |
| mrtIfTraceReceived The received trace identifier for this interface. | column | OctetString | .1.3.6.1.4.1.8708.2.12.2.2.1.1.43 |
| mrtIfTraceExpected Trace identifier used for matching against
the received trace identifier. | column | OctetString | .1.3.6.1.4.1.8708.2.12.2.2.1.1.44 |
| mrtIfTraceAlarmMode Controls if the trace identifier mismatch alarm
should be raised.
disabled - The alarm is disabled.
enabled - The alarm is raised if expected trace
i… | column | Enumeration | .1.3.6.1.4.1.8708.2.12.2.2.1.1.45 |
| mrtIfTraceMismatch Indicates if the expected trace identifier
differs from the received trace identifier.
A: The received trace identifier differs from
the expected trace identifier.
… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.46 |
| mrtIfTruncVc4Status deprecated Shows the status of the VC4(s) that this port is
connected to.
undefined - used when the port is not connected
to any VC4. Also used when an STM4 port is VC4s
th… | column | Enumeration | .1.3.6.1.4.1.8708.2.12.2.2.1.1.47 |
| mrtIfMsAlarmIndicationSignalW2C MS Alarm indication signal (MS-AIS) on the trunc
side. Applicable for SDH/Sonet signal formats.
A: An 'all ones' SDH signal is detected.
D: SDH signa… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.48 |
| mrtIfForwardAls Forward Automatic Laser Shut-down. Decides the
behaviour of the client laser (W2C) when the
trunc signal is defected.
disabled - The laser is NOT turned off at fail… | column | Enumeration | .1.3.6.1.4.1.8708.2.12.2.2.1.1.49 |
| mrtIfSlot The number of the slot where the interface is
located. | column | LUM-TCSlotNumber | .1.3.6.1.4.1.8708.2.12.2.2.1.1.5 |
| mrtIfSuppressRemoteAlarms Suppress AIS and RDI in the alarm list.
The fault status on the port object can, however,
be seen.
disabled - alarms are not suppressed.
enabled - al… | column | Enumeration | .1.3.6.1.4.1.8708.2.12.2.2.1.1.50 |
| mrtIfConfigurationCommand Command to change the signal format and,
if applicable, also the speed.
Synopsis: configure [<format> [<speed>]]
If no arguments are given, the user … | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.12.2.2.1.1.51 |
| mrtIfTrxCodeMismatch The inserted transceiver does not have a legal
manufacturer code.
A: A transceiver with illegal code is inserted.
D: The transceiver with illegal cod… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.52 |
| mrtIfTrxBitrateUnavailable The inserted transceiver does not support the requested
bit rate.
A: A transceiver with other supported bit rate than
the requested bit rate is inserted.
… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.53 |
| mrtIfTrxMissing An expected transceiver is missing.
A: An expected transceiver is missing.
D: The missing transceiver is inserted. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.54 |
| mrtIfTrxClass String that describes the transceiver class. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.12.2.2.1.1.55 |
| mrtIfEntityId Index in entity table.
-- Only used for notifications | column | Unsigned32 | .1.3.6.1.4.1.8708.2.12.2.2.1.1.56 |
| mrtIfTransmitterFailed The transceiver HW has detected a failure
in the transmitter part.
A: The transmitter has failed
D: The transmitter is OK again | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.57 |
| mrtIfReceiverSensitivity The lowest power that the receiver is guaranteed
to handle, in units of 0.1 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.12.2.2.1.1.58 |
| mrtIfPowerLevelLowRelativeThreshold The lower threshold for received power level in
units of 0.1 dB, relative to the receiver
sensitivity. | column | Integer32 | .1.3.6.1.4.1.8708.2.12.2.2.1.1.59 |
| mrtIfTxPort The number of the port where the TX-side of the
interface is located. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.12.2.2.1.1.6 |
| mrtIfFarEndLoopback Loop the client TX signal back to the client RX.
disabled - the signal is not looped
enabled - the signal is looped. | column | Enumeration | .1.3.6.1.4.1.8708.2.12.2.2.1.1.60 |
| mrtIfConfigureModeCommand Command to change the TRX mode: CLIENT or LINE.
Also select the TRX media.
Synopsis: configureMode [<trxMode>] [<trxMedia>]
If no arguments are given… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.12.2.2.1.1.61 |
| mrtIfTrxMode Shows if the port is configured as:
- normal CLIENT interface connected to non-Transmode
or non-Infinera client equipment, with non-colored,
or colored TRXes.
… | column | Enumeration | .1.3.6.1.4.1.8708.2.12.2.2.1.1.62 |
| mrtIfExpectedTxFrequency The expected frequency given in hundreds of GHz
(0.01 GHz). | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.12.2.2.1.1.63 |
| mrtIfTxFrequency The transmitted frequency given in hundreds of
GHz (0.01 GHz). | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.12.2.2.1.1.64 |
| mrtIfUnexpectedTxFrequency The actual frequency does not match the
pre-configured frequency.
A pre-configured frequency of '0' matches
all actual frequencies.
A: The configured… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.65 |
| mrtIfIllegalFrequency The frequency supported by the transceiver is not
recognized by the system.
A: Invalid or unknown frequency information is
detected in the (pluggable) transceive… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.66 |
| mrtIfTrxMedia Defines the media and capability of the TRX. | column | LUM-TCTrxMedia | .1.3.6.1.4.1.8708.2.12.2.2.1.1.67 |
| mrtIfTrxMediaMismatch The TRX media does not match the expected one.
A: Invalid or mismatching trx media is
detected.
D: The (pluggable) transceiver or board is
repl… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.12.2.2.1.1.68 |
| mrtIfLaserForcedOn When enabled, the laser is on regardless of whether
there is a trunc signal present or not.
disabled - the laser is only on when there is a
trunc signal.
… | column | Enumeration | .1.3.6.1.4.1.8708.2.12.2.2.1.1.69 |
| mrtIfRxPort The number of the port where the RX-side of the
interface is located. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.12.2.2.1.1.7 |
| mrtIfTruncAutoNegotiationMode Decides whether auto negotiation shall
be performed over the trunc connection.
This is applicable when the terminating
node at the other side of the
trunc is config… | column | Enumeration | .1.3.6.1.4.1.8708.2.12.2.2.1.1.70 |
| mrtIfObjectProperty Property mask. | column | LUM-TCObjectProperty | .1.3.6.1.4.1.8708.2.12.2.2.1.1.71 |
| mrtIfTxPowerLevel The transmitted power level in units of 0.1 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.12.2.2.1.1.72 |
| mrtIfLaserTempActual The actual laser temperature in units of
0.1 degrees centigrade. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.12.2.2.1.1.73 |
| mrtIfHighSpeed2 The expected signal bit rate in units of
1,000,000 bits (Mb) per second.
The value is given with 2 decimals,
so the resolution is 10 000 bits per second. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.12.2.2.1.1.74 |
| mrtIfRxSignalStatus The operational state for incoming (RX) signal
of the interface.
down - A fault that would lead to a protection
switch has occurred.
degraded - The s… | column | Enumeration | .1.3.6.1.4.1.8708.2.12.2.2.1.1.75 |
| mrtIfInvPhysIndexOrZero The row in the invPhysTable for this interface.
Set to 0 if not known. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.12.2.2.1.1.8 |
| mrtIfFormat The expected signal format.
The default value is board dependent. For information
about the default value for this particular board,
please refer to the user manual. | column | LUM-TCSignalFormat | .1.3.6.1.4.1.8708.2.12.2.2.1.1.9 |