mesMiscAssociateBwp
LUM-MES-MIB ·
.1.3.6.1.4.1.8708.2.32.2.10.1.1.24
Object
column
LUM-TCCommandString
Create a MEF Policer.
CIR (Commited Information Rate)
The average rate in bits/s up to which the network delivers
service frames and meets the defined performance objectives.
CBS (Commited Burst Size)
The maximum number of bytes available for a burst to remain
CIR-conformant. Packets conformant to CIR/CBS are marked as
green. Value is entered in kB, and can be interpreted as the
amount of data that can be sent consecutively at the port line rate.
Ex: 100 mBit/s * 100 ms = 1250 kB
1 Gbit/s * 32 ms = 4000 kB
1 Gbit/s * 10 ms = 1250 kB
10 Gbit/s * 1 ms = 1250 kB
EIR (Excess Information Rate)
The average rate in bits/s up to which the network may deliver
service frames without any performance objectives.
EBS(Excess Burst Size)
The maximum number of bytes available for a burst to remain
EIR-conformant. Packets conformant to EIR/EBS but not CIR/CBS
are marked as yellow. Value is entered in kB, and can be interpreted as the
amount of data that can be sent consecutively at the port line rate.
Ex: 100 mBit/s * 100 ms = 1250 kB
1 Gbit/s * 32 ms = 4000 kB
1 Gbit/s * 10 ms = 1250 kB
10 Gbit/s * 1 ms = 1250 kB
In color blind mode, the outgoing frame color is
based only on the profile status of each bucket. In
color aware mode, the outgoing frame color is based
on the incoming color and the profile status of each
bucket. The incoming color is derived from the
ingress classification stage.
Context
- MIB
- LUM-MES-MIB
- OID
.1.3.6.1.4.1.8708.2.32.2.10.1.1.24- Type
- column
- Access
- readonly
- Status
- current
- Parent
- mesMiscEntry
- Table
- mesMiscTable
- Siblings
- 44
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| mesMiscIndex An arbitrary index assigned to each Misc entry. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.32.2.10.1.1.1 |
| mesMiscMgmtVlanMacAddress1 The mac address of eth1. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.10 |
| mesMiscMgmtVlanMacAddress2 The mac address of eth2. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.11 |
| mesMiscConfigureAddress Change the IP address and netmask. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.12 |
| mesMiscMgmtVlanNode Indicates if mgmt VLAN is enabled in equipment-node
mib.
Note that if mgmt VLAN is disabled in node, it
overrides Misc/Administrative status.
(to change this settin… | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.10.1.1.13 |
| mesMiscMacAgeing The MAC table ageing time in seconds. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.32.2.10.1.1.14 |
| mesMiscMacGetTable Get MAC address table. It is possible to filter the MAC table per port,
per VLAN and per MAC address. The MAC address field also allows regular
expressions.
To sear… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.15 |
| mesMiscNoOfMegs The current number of MEGs associated with this
board. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.32.2.10.1.1.16 |
| mesMiscAssociateMeg Create and associate a MEG (MAID) for the board.
Identifier - A unique user defined identifier for the MEG.
Level - Maintenance domain level.
… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.17 |
| mesMiscNoOfErps The current number of ERPs associated with this
board. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.32.2.10.1.1.18 |
| mesMiscAssociateErp Create and associate an ERP (Ethernet Ring Protection) for the board.
VLAN ID - The VLAN ID that carries the control messages. The
VLAN ID… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.19 |
| mesMiscName The management name of the misc group, for example
'misc:1:2'. | column | LUM-TCMgmtNameString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.2 |
| mesMiscL2Mode The initial mode (switch or aggregator) of the board.
Switch - All ports are acting as NNI and all ports are trusted.
Aggregator - 1G ports are a… | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.10.1.1.20 |
| mesMiscConfigureMode Defines if the board should be acting as a switch or an aggregator.
Switch - All ports are acting as NNI and all ports trust each other.
Aggregat… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.21 |
| mesMiscIdentity For internal use only. | column | SNMPv2-SMICounter64 | .1.3.6.1.4.1.8708.2.32.2.10.1.1.22 |
| mesMiscAssociateClass Create a classification to be used in a policy.
Classification enables dynamic assignment of actions (rules) when
traffic is received or before traffic is sent.
The… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.23 |
| mesMiscWred Defines if WRED (Weighted Random Early Detection) is
enabled on the board.
disabled - WRED is disabled on the board.
enabled - WRED is enabled on the… | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.10.1.1.25 |
| mesMiscGetPacketMonitor Get data packet(s) from a specified interface. The monitor function
waits for a user defined maximum number of packets and for a user
defined maximum number of seconds.
… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.26 |
| mesMiscSfpPortUsageCurrent Indicates if the 1 Gbe port is connected to the front panel or
is connected to the CPU for mgmt VLAN.
Only applicable for emxp40Gii.
external - The 1 GbE port is co… | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.10.1.1.27 |
| mesMiscSfpPortUsageNext Indicates usage of the 1 Gbe port after a cold start of the board.
Only applicable for emxp40Gii.
external - The 1 GbE port will be connected to the front.
… | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.10.1.1.28 |
| mesMiscAssociateErrorProp Internal dialog command for configuring and create an Error Propagation rule.
Select the following:
- Trigger type
- Trigger MEP or Port depending on trigger type
- Action type
- … | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.29 |
| mesMiscObjectProperty Property mask. | column | LUM-TCObjectProperty | .1.3.6.1.4.1.8708.2.32.2.10.1.1.3 |
| mesMiscNoOfErpV2s The current number of ERPV2s associated with this
board. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.32.2.10.1.1.30 |
| mesMiscAssociateErpV2 Create and associate an ERP V2 (Ethernet Ring Protection V2) for the board.
Ring ID - The Ring Id and VLAN Id is used to uniquely define
t… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.31 |
| mesMiscAssociateVlanProt Dialog command for create and configuring a VLAN Protection Group.
The VLAN protection group is used for the EPR V2 ring protection
to define the VLAN protected by the ring.
Selec… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.32 |
| mesMiscCreateVlan Dialog command for create and configuring a VLAN Map Entry | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.33 |
| mesMiscEnablePtp1588 Enable precision time protocol 1588v2 transparent clock on all ports.
disabled - ptp 1588v2 transparent clock is disabled
enabled - ptp 1588v2 transp… | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.10.1.1.34 |
| mesMiscEnableStpMgmtVlan Enable spanning tree protocol for management vlan on all ports.
disabled - spanning tree protocol for mangagement vlan is disabled
enabled - panning … | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.10.1.1.35 |
| mesMiscAssociateClassAdvanced Create a classification to be used in a policy.
Classification enables dynamic assignment of actions (rules) when
traffic is received or before traffic is sent.
The… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.36 |
| mesMiscAssociateErpAdvanced Create and associate an ERP V2 (Ethernet Ring Protection V2) for the board.
Ring ID - The Ring Id and VLAN Id is used to uniquely define
t… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.37 |
| mesMiscAssociateMegAdvanced Create and associate a MEG (MAID) for the board.
Identifier - A unique user defined identifier for the MEG.
Level - Maintenance domain level.
… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.38 |
| mesMiscCreateClass Dialog command for creating a classifier. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.39 |
| mesMiscInternalReference For internal use only. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.32.2.10.1.1.4 |
| mesMiscCreateAction Dialog command for creating an action. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.40 |
| mesMiscCreateMeg Dialog command for creating a MEG. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.41 |
| mesMiscCreateMep Dialog command for creating a MEP. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.42 |
| mesMiscCreateErrorProp Dialog command for creating an error propagation. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.43 |
| mesMiscCreatePolicer Dialog command for creating a policer. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.44 |
| mesMiscResendConfig Dialog command to send a specific configuration. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.45 |
| mesMiscAdminStatus The administrative state for the object.
down - The object is de-activated. For a CU-less
system, admin status cannot be set to 'up' or
'service' if mgmt VLAN IP ad… | column | LUM-TCBoardOrInterfaceAdminStatus | .1.3.6.1.4.1.8708.2.32.2.10.1.1.5 |
| mesMiscOperStatus The operational state for the object.
notPresent - The object is not available.
down - The object is de-activated or there are
faults preventing its … | column | LUM-TCBoardOrInterfaceOperStatus | .1.3.6.1.4.1.8708.2.32.2.10.1.1.6 |
| mesMiscMgmtVlanIpAddress The IP address of the ethernet interface associated
with the mgmt VLAN.
Set to 0.0.0.0 if not used. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.8708.2.32.2.10.1.1.7 |
| mesMiscMgmtVlanNetMask The IP net mask of the ethernet interface associated
with the mgmt VLAN.
Set to 0.0.0.0 if not used. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.8708.2.32.2.10.1.1.8 |
| mesMiscMgmtVlanMacAddress0 The mac address of eth0. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.32.2.10.1.1.9 |