dcnIfTraceTransmitted
LUM-DCN-MIB ·
.1.3.6.1.4.1.8708.2.20.2.2.1.1.41
Object
The trace identifier to be transmitted from this
interface.
Set to empty string for default value:
<IP address>:<subrack>:<slot>:<port>
Note that only the last part of the address
is used.
Context
- MIB
- LUM-DCN-MIB
- OID
.1.3.6.1.4.1.8708.2.20.2.2.1.1.41- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- dcnIfEntry
- Table
- dcnIfTable
- Siblings
- 48
Values & Constraints
Type Constraints
range: 0..255
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| dcnIfIndex An arbitrary index assigned to each entry. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.20.2.2.1.1.1 |
| dcnIfMaxSpeed The expected signal bit rate in units of
1,000,000 bits (Mb) per second. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.20.2.2.1.1.10 |
| dcnIfOscMode The usage mode for the OSC channel
icn - Used for node internal communication
dcn - Used for external communication
(main CU only)
cus… | column | DcnOscMode | .1.3.6.1.4.1.8708.2.20.2.2.1.1.11 |
| dcnIfAdminStatus The administrative state for the interface.
down - The interface should be inactive.
service - The interface is activated but alarms
are suppressed. … | column | LUM-TCBoardOrInterfaceAdminStatus | .1.3.6.1.4.1.8708.2.20.2.2.1.1.12 |
| dcnIfOperStatus The operational state for the interface.
notPresent - The physical resources are not
available.
down - The interface is de-activated or the are
fault… | column | LUM-TCBoardOrInterfaceOperStatus | .1.3.6.1.4.1.8708.2.20.2.2.1.1.13 |
| dcnIfTxSignalStatus The operational state for outgoing (TX) signal
of the interface.
down - A fault that would lead to a protection
switch has occurred.
degraded - The s… | column | Enumeration | .1.3.6.1.4.1.8708.2.20.2.2.1.1.14 |
| dcnIfLinkDown A: Failure to negotiate a connection with the
other party.
D: A connection is negotiated. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.20.2.2.1.1.15 |
| dcnIfTxFrequency The transmitted frequency given. | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.20.2.2.1.1.16 |
| dcnIfObjectProperty Property mask. | column | LUM-TCObjectProperty | .1.3.6.1.4.1.8708.2.20.2.2.1.1.17 |
| dcnIfLaserStatus The operational state of the TX-side laser.
off - The laser is turned off.
on - The laser is turned on. | column | Enumeration | .1.3.6.1.4.1.8708.2.20.2.2.1.1.18 |
| dcnIfPowerLevel The received power level in units of 0.1 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.20.2.2.1.1.19 |
| dcnIfName The management name of the interface, for example
'osc:1:1:1-2', where the first number indicates
sub-rack, the second slot number and the third is
the port number.
Examples:
… | column | LUM-TCMgmtNameString | .1.3.6.1.4.1.8708.2.20.2.2.1.1.2 |
| dcnIfTxPowerLevel The transmitted power level in units of 0.1 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.20.2.2.1.1.20 |
| dcnIfReceiverSensitivity The lowest power that the receiver is guaranteed
to handle, in units of 0.1 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.20.2.2.1.1.21 |
| dcnIfPowerLevelLowRelativeThreshold The lower threshold for received power level in
units of 0.1 dB, relative to the receiver
sensitivity. | column | Integer32 | .1.3.6.1.4.1.8708.2.20.2.2.1.1.22 |
| dcnIfLaserTempActual The actual laser temperature in units of
0.1 degrees centigrade. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.20.2.2.1.1.23 |
| dcnIfTrxClass String that describes the transceiver class. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.20.2.2.1.1.24 |
| dcnIfHighSpeedMin The minmum speed in units of 1,000,000 bits (Mb)
per second. If this object reports a value of 'n'
then the speed of the interface is somewhere in
the range of 'n-500,000' to 'n+4… | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.8708.2.20.2.2.1.1.25 |
| dcnIfHighSpeedMax The maximum speed in units of 1,000,000 bits per
second. If this object reports a value of 'n'
then the speed of the interface is somewhere in
the range of 'n-500,000' to 'n+499,9… | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.8708.2.20.2.2.1.1.26 |
| dcnIfExpectedTxFrequency The expected frequency given in hundreds of GHz
(0.01 GHz). | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.20.2.2.1.1.27 |
| dcnIfLaserBias Measures laser bias current value in tenths of
mA (0.1 mA). | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.20.2.2.1.1.28 |
| dcnIfLossOfSignal Loss of signal.
Applicable for all signal formats.
A(ctivation): Active loss of signal HW indication.
D(e-activation): Inactive loss of signal HW
ind… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.20.2.2.1.1.29 |
| dcnIfDescr User configurable label. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.20.2.2.1.1.3 |
| dcnIfTrxCodeMismatch The inserted transceiver does not have a legal
manufacturer code.
A: A transceiver with illegal code is inserted.
D: The transceiver with illegal cod… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.20.2.2.1.1.30 |
| dcnIfTrxBitrateUnavailable The inserted transceiver does not support the requested
bit rate.
A: A transceiver with other supported bit rate than
the requested bit rate is inserted.
… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.20.2.2.1.1.31 |
| dcnIfTrxMissing An expected transceiver is missing.
A: An expected transceiver is missing.
D: The missing transceiver is inserted. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.20.2.2.1.1.32 |
| dcnIfTransmitterFailed The transceiver HW has detected a failure
in the transmitter part.
A: The transmitter has failed
D: The transmitter is OK again | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.20.2.2.1.1.33 |
| dcnIfIllegalFrequency The frequency supported by the transceiver is not
recognized by the system.
A: Invalid or unknown frequency information is
detected in the (pluggable) transceive… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.20.2.2.1.1.34 |
| dcnIfUnexpectedTxFrequency The actual frequency does not match the
pre-configured frequency.
A pre-configured frequency of '0' matches
all actual frequencies.
A: The configured… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.20.2.2.1.1.35 |
| dcnIfReceivedPowerHigh Received power level is too high.
Applicable for all signal formats.
A: The received power level exceeds the
the built-in overload threshold.
D: The … | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.20.2.2.1.1.36 |
| dcnIfReceivedPowerLow Received power level low threshold exceeded.
Applicable for all signal formats.
A: The received power level is below the
associated threshold.
D: The… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.20.2.2.1.1.37 |
| dcnIfTrxMediaMismatch The TRX media does not match the expected one.
A: Invalid or mismatching trx media is
detected.
D: The (pluggable) transceiver or board is
repl… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.20.2.2.1.1.38 |
| dcnIfProtocolVersionMismatch The peer interfaces uses different versions of the communication
protocol.
A: Incoming messages have the wrong version
D: Incoming messages have the … | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.20.2.2.1.1.39 |
| dcnIfSubrack The number of the subrack where the interface
is located. | column | LUM-TCSubrackNumber | .1.3.6.1.4.1.8708.2.20.2.2.1.1.4 |
| dcnIfRemoteDefectIndication The remote interfaces signals failures on the received
signal.
A: The remote interface signals failure
D: The remote interface does not signal failure | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.20.2.2.1.1.40 |
| dcnIfTraceReceived The received trace identifier for this interface. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.20.2.2.1.1.42 |
| dcnIfTraceExpected Trace identifier used for matching against
the received trace identifier. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.20.2.2.1.1.43 |
| dcnIfTraceAlarmMode Controls if the trace identifier mismatch alarm
should be raised.
disabled - The alarm is disabled.
enabled - The alarm is raised if expected trace
i… | column | Enumeration | .1.3.6.1.4.1.8708.2.20.2.2.1.1.44 |
| dcnIfSlot The number of the slot where the interface is
located. | column | LUM-TCSlotNumber | .1.3.6.1.4.1.8708.2.20.2.2.1.1.5 |
| dcnIfTraceMismatch Indicates if the expected trace identifier
differs from the received trace identifier.
A: The received trace identifier differs from
the expected trace identifier.
… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.20.2.2.1.1.55 |
| dcnIfLaserMode The administrative state of the TX-side laser
on - The laser is turned on.
als - Automatic Laser Shutdown/Turn-Off
when lossOfSignal is detected on t… | column | Enumeration | .1.3.6.1.4.1.8708.2.20.2.2.1.1.56 |
| dcnIfLinkSupervisionFailure The supervision procedure of the protection link
failed.
A: The protection board loses contact with its peer
D: The contact is re-established | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.20.2.2.1.1.57 |
| dcnIfAid The access identifier (AID) of the interface.
The format is according to GR-833. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.20.2.2.1.1.58 |
| dcnIfPhysicalLocation The physical location of the if.
The format is according to GR-833. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.20.2.2.1.1.59 |
| dcnIfTxPort The number of the port where the TX-side of the
interface is located. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.20.2.2.1.1.6 |
| dcnIfRxPort The number of the port where the RX-side of the
interface is located. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.20.2.2.1.1.7 |
| dcnIfInvPhysIndexOrZero The row in the invPhysTable for this interface.
Set to 0 if not known. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.20.2.2.1.1.8 |
| dcnIfType The expected signal type. | column | DcnSignalType | .1.3.6.1.4.1.8708.2.20.2.2.1.1.9 |