lcsErpsStatusTransmitAPS
LCOS-SX-MIB ·
.1.3.6.1.4.1.2356.14.2.24.3.17
Object
scalar
SNMPv2-TCDisplayString
The transmitted APS according to State Transition Tables in G.8032.
Context
- MIB
- LCOS-SX-MIB
- OID
.1.3.6.1.4.1.2356.14.2.24.3.17- Type
- scalar
- Access
- readonly
- Status
- current
- Parent
- lcsERPSConfigInstanceEntry
- Siblings
- 23
Values & Constraints
Type Constraints
range: 0..255
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| lcsErpsConfigInstanceClear If the owner has to be changed, then the clear check box allows to clear the RPL owner for that ERPS ring.
0: no clear
1: clear | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2356.14.2.24.3.10 |
| lcsErpsConfigInstanceTopologyChange 1: indicates that the topology changes in the sub-ring are propagated in the major ring.
0: indicates that the topology changes in the sub-ring are not propagated in the major rin… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2356.14.2.24.3.11 |
| lcsErpsConfigInstanceCommand 0:None
1:Manual Switch
2:Forced Switch
3:Clear
Please set InstancePort first. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2356.14.2.24.3.12 |
| lcsErpsConfigInstancePort 0:None
1:Port0
2:Port1
Please set InstanceCommand after specify InstancePort. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2356.14.2.24.3.13 |
| lcsErpsStatusProtectionState ERPS state according to State Transition Tables in G.8032. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.24.3.14 |
| lcsErpsStatusPort0 OK: State of East port is ok
SF: State of East port is Signal Fail | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.24.3.15 |
| lcsErpsStatusPort1 OK: State of West port is ok
SF: State of West port is Signal Fail | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.24.3.16 |
| lcsErpsStatusPort0ReceiveAPS The received APS on Port 0 according to State Transition Tables in G.8032. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.24.3.18 |
| lcsErpsStatusPort1ReceiveAPS The received APS on Port 1 according to State Transition Tables in G.8032. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.24.3.19 |
| lcsErpsConfigInstanceConfigured Down: This ERPS is only created and has not yet been configured - is not active.
Up: This ERPS is configured - is active. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.24.3.2 |
| lcsErpsStatusWTRRemaining Remaining WTR timeout in milliseconds. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2356.14.2.24.3.20 |
| lcsErpsStatusRPLUnblocked APS is received on the working flow. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.24.3.21 |
| lcsErpsStatusNoAPSReceived RAPS PDU is not received from the other end. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.24.3.22 |
| lcsErpsStatusPort0BlockStatus Block status for Port 0 (Both traffic and R-APS block status). R-APS channel is never blocked on sub-rings without virtual channel. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.24.3.23 |
| lcsErpsStatusPort1BlockStatus Block status for Port 1 (Both traffic and R-APS block status). R-APS channel is never blocked on sub-rings without virtual channel. | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.24.3.24 |
| lcsErpsStatusFOPAlarm Failure of Protocol Defect(FOP) status:
FOP is not detected
FOP is detected | scalar | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.24.3.25 |
| lcsErpsConfigInstanceGuardTime The period of the guard timer can be configured in 10 ms steps between 10 ms and 2 seconds, with a default value of 500 ms.
Guard timeout value to be used to prevent ring nodes fr… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2356.14.2.24.3.3 |
| lcsErpsConfigInstanceWTRTime The Wait To Restore timing value to be used in revertive switching.
The period of the WTR time can be configured by the operator in 1 minute steps between 5 and 12 minutes with a … | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2356.14.2.24.3.4 |
| lcsErpsConfigInstanceHoldOffTime The timing value to be used to make persistent check on Signal Fail before switching.
The range of the hold off timer is 0 to 10 seconds in steps of 100 ms | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2356.14.2.24.3.5 |
| lcsErpsConfigInstanceVersion ERPS Protocol Version - v1 or v2
1:v1
2:v2 | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2356.14.2.24.3.6 |
| lcsErpsConfigInstanceRevertive 1:Revertive mode
0:Non-Revertive mode | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2356.14.2.24.3.7 |
| lcsErpsConfigInstanceRPLRole It can be either RPL owner or RPL Neighbor.
0:None
1:RPL owner
2:RPL Neighbor
Please set RPLPort first. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2356.14.2.24.3.8 |
| lcsErpsConfigInstanceRPLPort This allows to select the east port or west port as the RPL block.
0:None
1:Port0
2:Port1
Please set RPLRole after specify RPLPort. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2356.14.2.24.3.9 |