lcsErpsConfigInstanceTopologyChange

LCOS-SX-MIB · .1.3.6.1.4.1.2356.14.2.24.3.11
MIB view Table view

Object

scalar r/w SNMPv2-SMIInteger32 
1: indicates that the topology changes in the sub-ring are propagated in the major ring.
0: indicates that the topology changes in the sub-ring are not propagated in the major ring.

Context

MIB
LCOS-SX-MIB
OID
.1.3.6.1.4.1.2356.14.2.24.3.11
Type
scalar
Access
readwrite
Status
current
Parent
lcsERPSConfigInstanceEntry
Siblings
23

Syntax

SNMPv2-SMIInteger32
Source
SNMPv2-SMIInteger32
Base type
Integer32

Values & Constraints

Type Constraints
range: -2147483648..2147483647

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
lcsErpsConfigInstanceClear
If the owner has to be changed, then the clear check box allows to clear the RPL owner for that ERPS ring. 0: no clear 1: clear
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.2356.14.2.24.3.10
lcsErpsConfigInstanceCommand
0:None 1:Manual Switch 2:Forced Switch 3:Clear Please set InstancePort first.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.2356.14.2.24.3.12
lcsErpsConfigInstancePort
0:None 1:Port0 2:Port1 Please set InstanceCommand after specify InstancePort.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.2356.14.2.24.3.13
lcsErpsStatusProtectionState
ERPS state according to State Transition Tables in G.8032.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.24.3.14
lcsErpsStatusPort0
OK: State of East port is ok SF: State of East port is Signal Fail
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.24.3.15
lcsErpsStatusPort1
OK: State of West port is ok SF: State of West port is Signal Fail
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.24.3.16
lcsErpsStatusTransmitAPS
The transmitted APS according to State Transition Tables in G.8032.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.24.3.17
lcsErpsStatusPort0ReceiveAPS
The received APS on Port 0 according to State Transition Tables in G.8032.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.24.3.18
lcsErpsStatusPort1ReceiveAPS
The received APS on Port 1 according to State Transition Tables in G.8032.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.24.3.19
lcsErpsConfigInstanceConfigured
Down: This ERPS is only created and has not yet been configured - is not active. Up: This ERPS is configured - is active.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.24.3.2
lcsErpsStatusWTRRemaining
Remaining WTR timeout in milliseconds.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.2356.14.2.24.3.20
lcsErpsStatusRPLUnblocked
APS is received on the working flow.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.24.3.21
lcsErpsStatusNoAPSReceived
RAPS PDU is not received from the other end.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.24.3.22
lcsErpsStatusPort0BlockStatus
Block status for Port 0 (Both traffic and R-APS block status). R-APS channel is never blocked on sub-rings without virtual channel.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.24.3.23
lcsErpsStatusPort1BlockStatus
Block status for Port 1 (Both traffic and R-APS block status). R-APS channel is never blocked on sub-rings without virtual channel.
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.24.3.24
lcsErpsStatusFOPAlarm
Failure of Protocol Defect(FOP) status: FOP is not detected FOP is detected
scalarSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.24.3.25
lcsErpsConfigInstanceGuardTime
The period of the guard timer can be configured in 10 ms steps between 10 ms and 2 seconds, with a default value of 500 ms. Guard timeout value to be used to prevent ring nodes fr…
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.2356.14.2.24.3.3
lcsErpsConfigInstanceWTRTime
The Wait To Restore timing value to be used in revertive switching. The period of the WTR time can be configured by the operator in 1 minute steps between 5 and 12 minutes with a …
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.2356.14.2.24.3.4
lcsErpsConfigInstanceHoldOffTime
The timing value to be used to make persistent check on Signal Fail before switching. The range of the hold off timer is 0 to 10 seconds in steps of 100 ms
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.2356.14.2.24.3.5
lcsErpsConfigInstanceVersion
ERPS Protocol Version - v1 or v2 1:v1 2:v2
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.2356.14.2.24.3.6
lcsErpsConfigInstanceRevertive
1:Revertive mode 0:Non-Revertive mode
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.2356.14.2.24.3.7
lcsErpsConfigInstanceRPLRole
It can be either RPL owner or RPL Neighbor. 0:None 1:RPL owner 2:RPL Neighbor Please set RPLPort first.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.2356.14.2.24.3.8
lcsErpsConfigInstanceRPLPort
This allows to select the east port or west port as the RPL block. 0:None 1:Port0 2:Port1 Please set RPLRole after specify RPLPort.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.2356.14.2.24.3.9