lcsACLACECounter

LCOS-SX-MIB · .1.3.6.1.4.1.2356.14.2.9.3.2.1.16
MIB view Table view

Object

column SNMPv2-SMICounter32 
The counter indicates the number of times the ACE was
hit by a frame.

Context

MIB
LCOS-SX-MIB
OID
.1.3.6.1.4.1.2356.14.2.9.3.2.1.16
Type
column
Access
readonly
Status
current
Parent
lcsACLACEEntry
Table
lcsACLACETable
Siblings
55

Syntax

SNMPv2-SMICounter32
Source
SNMPv2-SMICounter32
Base type
Unsigned32

Values & Constraints

Enumerated Values
1class0
2class1
3class2
4class3
5class4
6class5
7class6
8class7
Type Constraints
range: 0..4294967295

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
lcsACLACEIndex
The index.
columnInteger32.1.3.6.1.4.1.2356.14.2.9.3.2.1.1
lcsACLACEFilterPort
When 'Action' is 'Filter' can set. 0: Disable, Port n: The ACE applies to this port number, where n is the number of the switch port. range: 0 - Port number.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.9.3.2.1.10
lcsACLACEDenyPortRedirect
Frames that hit the ACE are redirected to the port number specified here.Disabled,indicates that the port redirect operation is disabled. When 'Action' is 'Deny' can set. 0: disab…
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.9.3.2.1.11
lcsACLACERateLimiter
default: 0, 0: Disable range : 0 - 16
columnInteger32.1.3.6.1.4.1.2356.14.2.9.3.2.1.12
lcsACLACEMirror
default: 0, 0: disable - Frames matching the ACE are not mirrored. 1: enable - Frames matching the ACE are mirrored.
columnAdminMode.1.3.6.1.4.1.2356.14.2.9.3.2.1.13
lcsACLACELogging
default: 0, 0: disable - Frames matching the ACE are not logged. 1: enable - Frames matching the ACE are stored in the system log.
columnAdminMode.1.3.6.1.4.1.2356.14.2.9.3.2.1.14
lcsACLACEShutdown
default: 0, 0: disable - Port shut down is disabled for the AC. 1: enable - If a frame matches the ACE, the ingress port will be disabled.
columnAdminMode.1.3.6.1.4.1.2356.14.2.9.3.2.1.15
lcsACLACEVLAN8021QTagged
Specify whether frames can hit the action according to the 802.1Q tagged. default: 2, 0: disable - Untagged frame only. 1: enable - Tagged frame only. 2: Any - Any value is allowe…
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.17
lcsACLACEVLANVID
Specify the VLAN ID filter for this ACE. The vid can't be set when 802.1Q Tagged is disabled. default: 0, 0: Any - No VLAN ID filter is specified. range : 0 - 4094
columnInteger32.1.3.6.1.4.1.2356.14.2.9.3.2.1.18
lcsACLACEVLANTagPriority
Specify the tag priority for this ACE. The tag priority can't be set when 802.1Q Tagged is disabled. range: 0-14 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 8:0-1 9:2-3 10:4-5 11:6-7 12:0-3 1…
columnInteger32.1.3.6.1.4.1.2356.14.2.9.3.2.1.19
lcsACLACEID
If the ACE ID is specified and an entry with this ACE ID already exists, the ACE will be modified. Otherwise, a new ACE will be added. range : 1 - 256.
columnInteger32.1.3.6.1.4.1.2356.14.2.9.3.2.1.2
lcsACLACESMAC
Configure source MAC address for this ACE. <mac-address>: A frame that hits this ACE matches this source MAC address value. xx-xx-xx-xx-xx-xx. Any: Don't care.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.9.3.2.1.20
lcsACLACEDMACType
DMAC Type. default: 0, 0: Any - Don't care. 1: Multicast - Frame must be multicast. 2: Broadcast - Frame must be broadcast. 3: Unicast - Frame must be unicast. 4: mac address. 5: …
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.21
lcsACLACEDMAC
Configure destination MAC address for this ACE. <mac-address>: A frame that hits this ACE matches this destination MAC address value. xx-xx-xx-xx-xx-xx.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.9.3.2.1.22
lcsACLACEEtherType
0: Any range : 0, or 1536(0x0600) - 65535(0xffff) but excluding 0x0800(IPv4) 0x0806(ARP) and 0x86DD(IPv6). -1: No data.
columnInteger32.1.3.6.1.4.1.2356.14.2.9.3.2.1.23
lcsACLACEArpOpCode
Configure ARP opcode for this ACE. default: 0, 0: Any - Don't care. 1: arp. 2: rarp. 3: other. 4: No data.
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.24
lcsACLACEArpFlagsRequestReply
Specify the available ARP/RARP opcode (OP) flag for this ACE. default: 2, 0: Frame must have ARP Reply or RARP Reply OP flag. 1: Frame must have ARP Request or RARP Request OP fla…
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.25
lcsACLACEArpFlagsArpSMac
Specify whether frames can hit the action according to their sender hardware address field (SHA) settings. default: 2, 0: ARP frames where SHA is not equal to the SMAC address. 1:…
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.26
lcsACLACEArpFlagsRarpDmac
Specify whether frames can hit the action according to their target hardware address field (THA) settings. default: 2, 0: RARP frames where THA is not equal to the DMAC address. 1…
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.27
lcsACLACEArpFlagsLength
Specify whether frames can hit the action according to their ARP/RARP hardware address length (HLN) and protocol address length (PLN) settings. default: 2, 0: ARP/RARP frames wher…
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.28
lcsACLACEArpFlagsIp
Specify whether frames can hit the action according to their ARP/RARP hardware address space (HRD) settings. default: 2, 0: ARP/RARP frames where the HLD is not equal to Ethernet(…
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.29
lcsACLACENextID
If the next ACE ID is non zero, the ACE will be placed before this ACE in the list. If the next ACE ID is zero, the ACE will be placed last in the list. range : 0 - 256.
columnInteger32.1.3.6.1.4.1.2356.14.2.9.3.2.1.3
lcsACLACEArpFlagsEthernet
Specify whether frames can hit the action according to their ARP/RARP protocol address space (PRO) settings. default: 2, 0: ARP/RARP frames where the PRO is not equal to IP\n(0x80…
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.30
lcsACLACESIPType
Configure source IP address for this ACE. default: 0, 0: Any - Don't care. 1: IP Address. 2: Network. 3: No data.
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.31
lcsACLACESIPIPAddress
A frame that hits this ACE matches this source IP address value.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.2356.14.2.9.3.2.1.32
lcsACLACESIPIPMask
Specific sender IP mask in dotted decimal notation.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.2356.14.2.9.3.2.1.33
lcsACLACEDIPType
Configure destination IP address for this ACE. default: 0, 0: Any - Don't care. 1: IP Address. 2: Network. 3: No data.
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.34
lcsACLACEDIPIPAddress
A frame that hits this ACE matches this destination IP address value.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.2356.14.2.9.3.2.1.35
lcsACLACEDIPIPMask
Specific sender IP mask in dotted decimal notation.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.2356.14.2.9.3.2.1.36
lcsACLACEIPProtocol
Specify the IP protocol filter for this ACE. default: 0, 0: Any, 1: ICMP, 2: UDP, 3: TCP, 4: Other, 5: no data.
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.37
lcsACLACEIPProtocolValue
Configure IP protocol value for this ACE when IP Protocol is 'other'. default: 256, 256: No data. range : 0 - 256
columnInteger32.1.3.6.1.4.1.2356.14.2.9.3.2.1.38
lcsACLACEIPFlagsTTL
Specify the Time-to-Live settings for this ACE. default: 0, 0: zero, 1: Non-Zero 2: Any,, 3: No data.
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.39
lcsACLACEIPFlagsFragment
Specify the fragment offset settings for this ACE. default: 2, 0: No, 1: Yes, 2: Any, 3: No data.
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.40
lcsACLACEIPFlagsOptions
Specify the options flag setting for this ACE. default: 2, 0: No, 1: Yes, 2: Any, 3: No data.
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.41
lcsACLACEICMPType
Configure ICMP type for this ACE. default: 256, 256: Any - Don't care. 257: No data. range : 0 - 257.
columnInteger32.1.3.6.1.4.1.2356.14.2.9.3.2.1.42
lcsACLACEICMPCode
Configure ICMP code for this ACE. default: 256, 256: Any - Don't care. 257: No data. range : 0 - 257.
columnInteger32.1.3.6.1.4.1.2356.14.2.9.3.2.1.43
lcsACLACESourcePort
Configure Source UDP/TCP port range for this ACE. default: any, specific: 0~65535, range : 0 - 65535.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.9.3.2.1.44
lcsACLACEDestPort
Configure Destination UDP/TCP port range for this ACE. default: any, specific: 0~65535, range : 0 - 65535.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.9.3.2.1.45
lcsACLACETCPFlagsFin
Configure TCP (FIN) flags for this ACE. default: 2, 0: TCP frames where the FIN field is unset. 1: TCP frames where the FIN field is set. 2: Any - Don't care. 3: No data.
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.46
lcsACLACETCPFlagsSyn
Configure TCP (SYN) flags for this ACE. default: 2, 0: TCP frames where the SYN field is unset. 1: TCP frames where the SYN field is set. 2: Any - Don't care. 3: No data.
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.47
lcsACLACETCPFlagsRst
Configure TCP (RST) flags for this ACE. default: 2, 0: TCP frames where the RST field is unset. 1: TCP frames where the RST field is set. 2: Any - Don't care. 3: No data.
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.48
lcsACLACETCPFlagsPsh
Configure TCP (PSH) flags for this ACE. default: 2, 0: TCP frames where the PSH field is unset. 1: TCP frames where the PSH field is set. 2: Any - Don't care. 3: No data.
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.49
lcsACLACEIngressPort
Indicates the ingress port of the ACE. Possible values are: 0: All,The ACE will match all ingress port. Port n: The ACE will match a specific ingress port.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.9.3.2.1.5
lcsACLACETCPFlagsAck
Configure TCP (ACK) flags for this ACE. default: 2, 0: TCP frames where the ACK field is unset. 1: TCP frames where the ACK field is set. 2: Any - Don't care. 3: No data.
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.50
lcsACLACETCPFlagsUrg
Configure TCP (URG) flags for this ACE. default: 2, 0: TCP frames where the URG field is unset. 1: TCP frames where the URG field is set. 2: Any - Don't care. 3: No data.
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.51
lcsACLACEIPv6SIPAddress
When 'Specific' is selected for the source IPv6 filter, you can enter a specific SIPv6 address. The field only supported last 32 bits for IPv6 address.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.9.3.2.1.52
lcsACLACEIPv6SIPBitmask
When 'Specific' is selected for the source IPv6 filter, you can enter a specific SIPv6 mask. The field only supported last 32 bits for IPv6 address.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.9.3.2.1.53
lcsACLACEIPv6HopLimit
Specify the hop limit settings for this ACE. default: 2, 0: Where the Hop Limit field is unset. 1: Where the Hop Limit field is set. 2: Any - Don't care, 3: No data.
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.54
lcsACLACESMACMask
Configure source MAC address mask for this ACE. <mac-address>: A frame that hits this ACE matches this source MAC address value. xx-xx-xx-xx-xx-xx.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.9.3.2.1.56
lcsACLACEDMACMask
Configure destination MAC address mask for this ACE. <mac-address>: A frame that hits this ACE matches this destination MAC address value. xx-xx-xx-xx-xx-xx.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.2356.14.2.9.3.2.1.57
lcsACLACERowStatus
This object indicates the status of this entry, and is used to create/delete entries. Any object in an entry of this table may be modified while the value of the corresponding in…
columnSNMPv2-TCRowStatus.1.3.6.1.4.1.2356.14.2.9.3.2.1.58
lcsACLACEPortPolicyNumber
policy value. range : 0 - 127. 0: Any.
columnInteger32.1.3.6.1.4.1.2356.14.2.9.3.2.1.6
lcsACLACEPortPolicyBitmask
When 'Specific' is selected for the policy filter, you can enter a specific policy bitmask. range : 0 - 127, 0: no data.
columnInteger32.1.3.6.1.4.1.2356.14.2.9.3.2.1.7
lcsACLACEFrameType
Select the frame type for this ACE. When change the type Related oid will set default. 0: any, 1: etype, 2: arp, 3: ipv4, 4: ipv6.
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.8
lcsACLACEAction
0: Deny 1: Permit 2: Filter
columnEnumeration.1.3.6.1.4.1.2356.14.2.9.3.2.1.9