lcsACLACEArpFlagsLength
LCOS-SX-MIB ·
.1.3.6.1.4.1.2356.14.2.9.3.2.1.28
Object
column
r/w
Enumeration
Specify whether frames can hit the action according to their ARP/RARP hardware address length (HLN) and protocol address length (PLN) settings. default: 2, 0: ARP/RARP frames where the HLN is not equal to Ethernet(0x06) or the (PLN) is not equal to IPv4(0x04). 1: ARP/RARP frames where the HLN is equal to Ethernet (0x06) and the (PLN) is equal to IPv4(0x04). 2: Any - Don't care. 3: No data.
Context
- MIB
- LCOS-SX-MIB
- OID
.1.3.6.1.4.1.2356.14.2.9.3.2.1.28- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- lcsACLACEEntry
- Table
- lcsACLACETable
- Siblings
- 55
Syntax
Enumeration
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| lcsACLACEIndex The index. | column | Integer32 | .1.3.6.1.4.1.2356.14.2.9.3.2.1.1 |
| lcsACLACEFilterPort When 'Action' is 'Filter' can set.
0: Disable,
Port n: The ACE applies to this port number, where n is
the number of the switch port.
range: 0 - Port number. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.9.3.2.1.10 |
| lcsACLACEDenyPortRedirect Frames that hit the ACE are redirected to the port
number specified here.Disabled,indicates that the port
redirect operation is disabled.
When 'Action' is 'Deny' can set.
0: disab… | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.9.3.2.1.11 |
| lcsACLACERateLimiter default: 0,
0: Disable
range : 0 - 16 | column | Integer32 | .1.3.6.1.4.1.2356.14.2.9.3.2.1.12 |
| lcsACLACEMirror default: 0,
0: disable - Frames matching the ACE are not mirrored.
1: enable - Frames matching the ACE are mirrored. | column | AdminMode | .1.3.6.1.4.1.2356.14.2.9.3.2.1.13 |
| lcsACLACELogging default: 0,
0: disable - Frames matching the ACE are not logged.
1: enable - Frames matching the ACE are stored in the
system log. | column | AdminMode | .1.3.6.1.4.1.2356.14.2.9.3.2.1.14 |
| lcsACLACEShutdown default: 0,
0: disable - Port shut down is disabled for the AC.
1: enable - If a frame matches the ACE, the ingress port
will be disabled. | column | AdminMode | .1.3.6.1.4.1.2356.14.2.9.3.2.1.15 |
| lcsACLACECounter The counter indicates the number of times the ACE was
hit by a frame. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2356.14.2.9.3.2.1.16 |
| lcsACLACEVLAN8021QTagged Specify whether frames can hit the action according to
the 802.1Q tagged.
default: 2,
0: disable - Untagged frame only.
1: enable - Tagged frame only.
2: Any - Any value is allowe… | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.17 |
| lcsACLACEVLANVID Specify the VLAN ID filter for this ACE.
The vid can't be set when 802.1Q Tagged is disabled.
default: 0,
0: Any - No VLAN ID filter is specified.
range : 0 - 4094 | column | Integer32 | .1.3.6.1.4.1.2356.14.2.9.3.2.1.18 |
| lcsACLACEVLANTagPriority Specify the tag priority for this ACE.
The tag priority can't be set when 802.1Q Tagged is disabled.
range: 0-14
0:0
1:1
2:2
3:3
4:4
5:5
6:6
7:7
8:0-1
9:2-3
10:4-5
11:6-7
12:0-3
1… | column | Integer32 | .1.3.6.1.4.1.2356.14.2.9.3.2.1.19 |
| lcsACLACEID If the ACE ID is specified and an entry with this ACE ID
already exists, the ACE will be modified. Otherwise, a
new ACE will be added.
range : 1 - 256. | column | Integer32 | .1.3.6.1.4.1.2356.14.2.9.3.2.1.2 |
| lcsACLACESMAC Configure source MAC address for this ACE.
<mac-address>: A frame that hits this ACE matches this
source MAC address value. xx-xx-xx-xx-xx-xx.
Any: Don't care. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.9.3.2.1.20 |
| lcsACLACEDMACType DMAC Type.
default: 0,
0: Any - Don't care.
1: Multicast - Frame must be multicast.
2: Broadcast - Frame must be broadcast.
3: Unicast - Frame must be unicast.
4: mac address.
5: … | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.21 |
| lcsACLACEDMAC Configure destination MAC address for this ACE.
<mac-address>: A frame that hits this ACE matches this
destination MAC address value. xx-xx-xx-xx-xx-xx. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.9.3.2.1.22 |
| lcsACLACEEtherType 0: Any
range : 0, or 1536(0x0600) - 65535(0xffff) but excluding 0x0800(IPv4) 0x0806(ARP) and
0x86DD(IPv6).
-1: No data. | column | Integer32 | .1.3.6.1.4.1.2356.14.2.9.3.2.1.23 |
| lcsACLACEArpOpCode Configure ARP opcode for this ACE.
default: 0,
0: Any - Don't care.
1: arp.
2: rarp.
3: other.
4: No data. | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.24 |
| lcsACLACEArpFlagsRequestReply Specify the available ARP/RARP opcode (OP) flag for this ACE.
default: 2,
0: Frame must have ARP Reply or RARP Reply OP flag.
1: Frame must have ARP Request or RARP Request OP fla… | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.25 |
| lcsACLACEArpFlagsArpSMac Specify whether frames can hit the action according to their
sender hardware address field (SHA) settings.
default: 2,
0: ARP frames where SHA is not equal to the SMAC address.
1:… | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.26 |
| lcsACLACEArpFlagsRarpDmac Specify whether frames can hit the action according to
their target hardware address field (THA) settings.
default: 2,
0: RARP frames where THA is not equal to the DMAC address.
1… | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.27 |
| lcsACLACEArpFlagsIp Specify whether frames can hit the action according to
their ARP/RARP hardware address space (HRD) settings.
default: 2,
0: ARP/RARP frames where the HLD is not equal to Ethernet(… | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.29 |
| lcsACLACENextID If the next ACE ID is non zero, the ACE will be placed
before this ACE in the list. If the next ACE ID is zero,
the ACE will be placed last in the list.
range : 0 - 256. | column | Integer32 | .1.3.6.1.4.1.2356.14.2.9.3.2.1.3 |
| lcsACLACEArpFlagsEthernet Specify whether frames can hit the action
according to their ARP/RARP protocol address space (PRO) settings.
default: 2,
0: ARP/RARP frames where the PRO is not equal to IP\n(0x80… | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.30 |
| lcsACLACESIPType Configure source IP address for this ACE.
default: 0,
0: Any - Don't care.
1: IP Address.
2: Network.
3: No data. | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.31 |
| lcsACLACESIPIPAddress A frame that hits this ACE matches this source IP address
value. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2356.14.2.9.3.2.1.32 |
| lcsACLACESIPIPMask Specific sender IP mask in dotted decimal notation. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2356.14.2.9.3.2.1.33 |
| lcsACLACEDIPType Configure destination IP address for this ACE.
default: 0,
0: Any - Don't care.
1: IP Address.
2: Network.
3: No data. | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.34 |
| lcsACLACEDIPIPAddress A frame that hits this ACE matches this destination IP
address value. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2356.14.2.9.3.2.1.35 |
| lcsACLACEDIPIPMask Specific sender IP mask in dotted decimal notation. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2356.14.2.9.3.2.1.36 |
| lcsACLACEIPProtocol Specify the IP protocol filter for this ACE.
default: 0,
0: Any,
1: ICMP,
2: UDP,
3: TCP,
4: Other,
5: no data. | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.37 |
| lcsACLACEIPProtocolValue Configure IP protocol value for this ACE when IP Protocol
is 'other'.
default: 256,
256: No data.
range : 0 - 256 | column | Integer32 | .1.3.6.1.4.1.2356.14.2.9.3.2.1.38 |
| lcsACLACEIPFlagsTTL Specify the Time-to-Live settings for this ACE.
default: 0,
0: zero,
1: Non-Zero
2: Any,,
3: No data. | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.39 |
| lcsACLACEIPFlagsFragment Specify the fragment offset settings for this ACE.
default: 2,
0: No,
1: Yes,
2: Any,
3: No data. | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.40 |
| lcsACLACEIPFlagsOptions Specify the options flag setting for this ACE.
default: 2,
0: No,
1: Yes,
2: Any,
3: No data. | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.41 |
| lcsACLACEICMPType Configure ICMP type for this ACE.
default: 256,
256: Any - Don't care.
257: No data.
range : 0 - 257. | column | Integer32 | .1.3.6.1.4.1.2356.14.2.9.3.2.1.42 |
| lcsACLACEICMPCode Configure ICMP code for this ACE.
default: 256,
256: Any - Don't care.
257: No data.
range : 0 - 257. | column | Integer32 | .1.3.6.1.4.1.2356.14.2.9.3.2.1.43 |
| lcsACLACESourcePort Configure Source UDP/TCP port range for this ACE.
default: any,
specific: 0~65535,
range : 0 - 65535. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.9.3.2.1.44 |
| lcsACLACEDestPort Configure Destination UDP/TCP port range for this ACE.
default: any,
specific: 0~65535,
range : 0 - 65535. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.9.3.2.1.45 |
| lcsACLACETCPFlagsFin Configure TCP (FIN) flags for this ACE.
default: 2,
0: TCP frames where the FIN field is unset.
1: TCP frames where the FIN field is set.
2: Any - Don't care.
3: No data. | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.46 |
| lcsACLACETCPFlagsSyn Configure TCP (SYN) flags for this ACE.
default: 2,
0: TCP frames where the SYN field is unset.
1: TCP frames where the SYN field is set.
2: Any - Don't care.
3: No data. | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.47 |
| lcsACLACETCPFlagsRst Configure TCP (RST) flags for this ACE.
default: 2,
0: TCP frames where the RST field is unset.
1: TCP frames where the RST field is set.
2: Any - Don't care.
3: No data. | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.48 |
| lcsACLACETCPFlagsPsh Configure TCP (PSH) flags for this ACE.
default: 2,
0: TCP frames where the PSH field is unset.
1: TCP frames where the PSH field is set.
2: Any - Don't care.
3: No data. | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.49 |
| lcsACLACEIngressPort Indicates the ingress port of the ACE. Possible values are:
0: All,The ACE will match all ingress port.
Port n: The ACE will match a specific ingress port. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.9.3.2.1.5 |
| lcsACLACETCPFlagsAck Configure TCP (ACK) flags for this ACE.
default: 2,
0: TCP frames where the ACK field is unset.
1: TCP frames where the ACK field is set.
2: Any - Don't care.
3: No data. | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.50 |
| lcsACLACETCPFlagsUrg Configure TCP (URG) flags for this ACE.
default: 2,
0: TCP frames where the URG field is unset.
1: TCP frames where the URG field is set.
2: Any - Don't care.
3: No data. | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.51 |
| lcsACLACEIPv6SIPAddress When 'Specific' is selected for the source IPv6 filter,
you can enter a specific SIPv6 address.
The field only supported last 32 bits for IPv6 address. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.9.3.2.1.52 |
| lcsACLACEIPv6SIPBitmask When 'Specific' is selected for the source IPv6 filter,
you can enter a specific SIPv6 mask.
The field only supported last 32 bits for IPv6 address. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.9.3.2.1.53 |
| lcsACLACEIPv6HopLimit Specify the hop limit settings for this ACE.
default: 2,
0: Where the Hop Limit field is unset.
1: Where the Hop Limit field is set.
2: Any - Don't care,
3: No data. | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.54 |
| lcsACLACESMACMask Configure source MAC address mask for this ACE.
<mac-address>: A frame that hits this ACE matches this
source MAC address value. xx-xx-xx-xx-xx-xx. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.9.3.2.1.56 |
| lcsACLACEDMACMask Configure destination MAC address mask for this ACE.
<mac-address>: A frame that hits this ACE matches this
destination MAC address value. xx-xx-xx-xx-xx-xx. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2356.14.2.9.3.2.1.57 |
| lcsACLACERowStatus This object indicates the status of this entry, and is
used to create/delete entries. Any object in an entry of
this table may be modified while the value of the
corresponding in… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.2356.14.2.9.3.2.1.58 |
| lcsACLACEPortPolicyNumber policy value.
range : 0 - 127.
0: Any. | column | Integer32 | .1.3.6.1.4.1.2356.14.2.9.3.2.1.6 |
| lcsACLACEPortPolicyBitmask When 'Specific' is selected for the policy filter,
you can enter a specific policy bitmask.
range : 0 - 127, 0: no data. | column | Integer32 | .1.3.6.1.4.1.2356.14.2.9.3.2.1.7 |
| lcsACLACEFrameType Select the frame type for this ACE.
When change the type Related oid will set default.
0: any,
1: etype,
2: arp,
3: ipv4,
4: ipv6. | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.8 |
| lcsACLACEAction 0: Deny
1: Permit
2: Filter | column | Enumeration | .1.3.6.1.4.1.2356.14.2.9.3.2.1.9 |