slcDevPortCfgDialbackDelay
LANTRONIX-SLC-MIB ·
.1.3.6.1.4.1.244.1.1.4.2.2.2.1.88
Object
When slcDevPortCfgModemState is set to dialback or cbcpServer, specifies the delay between the dial-in and dial-out portion of the dialing sequence.
Context
- MIB
- LANTRONIX-SLC-MIB
- OID
.1.3.6.1.4.1.244.1.1.4.2.2.2.1.88- Type
- column
- Access
- readonly
- Status
- current
- Units
- seconds
- Parent
- slcDevPortCfgEntry
- Table
- slcDevPortCfgTable
- Siblings
- 119
Syntax
seconds SNMPv2-SMIInteger32
- Source
- SNMPv2-SMIInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| slcDevPortId The identifier for a Device Port. | column | Integer32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.1 |
| slcDevPortCfgSSHPort TCP Port number for SSH in connections. | column | Integer32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.10 |
| slcDevPortCfgDevNumExpOutlets If the device port is connected to a ServerTech CDU, specifies
the number of outlets on the expansion ServerTech unit. This
object is deprecated, and has been replaced by the RPM… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.100 |
| slcDevPortCfgReversePinout If enabled, swaps the positions of the serial lines, such
that the direction of data or the signal is reversed.
For instance, TX is swapped with RX. Enabling Reverse
Pinout f… | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.101 |
| slcDevPortCfgUSBVBUS For SLC8000 USB Device Ports only. If enabled, the USB VBUS
signal provides power to the USB device attached to a device
port. Disabling VBUS will power down the device as long … | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.102 |
| slcDevPortCfgAssertDTR For RJ45 Device Ports only. By default, DTR is asserted on a
device port nearly all of the time (except momentarily when a
port is opened for operations). Unchecking this optio… | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.103 |
| slcDevPortCfgPortType Indicates the connector type on the device port: RJ45 or USB. | column | Enumeration | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.104 |
| slcDevPortCfgTelnetTimeoutDataDirection If slcDevPortCfgTelnetTimeout is enabled, this setting
indicates the direction of data used to determine if the
connection has timed out. | column | TimeoutDataDirection | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.105 |
| slcDevPortCfgSSHTimeoutDataDirection If slcDevPortCfgSSHTimeout is enabled, this setting indicates
the direction of data used to determine if the connection has
timed out. | column | TimeoutDataDirection | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.106 |
| slcDevPortCfgTCPTimeoutDataDirection If slcDevPortCfgTCPTimeout is enabled, this setting indicates
the direction of data used to determine if the connection has
timed out. | column | TimeoutDataDirection | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.107 |
| slcDevPortCfgIdleTimeoutMessage If enabled, a message will be displayed to a user when their
connection to a device port will be terminated soon due to
the connection being idle. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.108 |
| slcDevPortCfgNumberOfSessionsMessage If enabled, a message will be displayed to a user when
connecting to a device port that indicates how many users
are currently connected to the device port. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.109 |
| slcDevPortCfgSSHAuth If enabled, the user is required to authenticate to access
a Device Port with SSH. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.11 |
| slcDevPortCfgMinimizeLatency If enabled, device port latency will be minimized by
reducing read delays. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.110 |
| slcDevPortCfgTelnetSoftIAC If enabled, the Telnet server will not block waiting for
the initial Telnet protocol IAC option responses. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.111 |
| slcDevPortCfgSendTermString If enabled, and a slcDevPortCfgTerminationString is defined,
when a network connection to a device port is terminated, the
termination string is sent to the device connected to … | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.112 |
| slcDevPortCfgTerminationString The termination string sent to the device connected to the
device port if slcDevPortCfgSendTermString is enabled. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.113 |
| slcDevPortCfgPowerManagementSeq The key sequence that displays the Power Management menu
when a user is connected to a device port. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.114 |
| slcDevPortCfgPowerSupplies A string that describes the managed power supplies configured
for the device port. A device port can have up to four power
supplies that provide power for the device connected t… | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.115 |
| slcDevPortCfgToggleDTR Applies to RJ45 device ports only. If enabled, when a user
disconnects from a device port, DTR will be toggled. This
feature can be used when a serial connection requires DSR… | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.116 |
| slcDevPortCfgTokenAction For Token and Data Detection, a string containing one or more
actions that will be performed if a data trigger occurs:
syslog, email, trap, sendstring, powersupply. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.117 |
| slcDevPortCfgTokenSendString For Token and Data Detection (previously called 'Email
Logging'), if the Send String action is enabled, this object
defines the string to send to the device connected to the
de… | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.118 |
| slcDevPortCfgTokenPowerSupply For Token and Data Detection (previously called 'Email
Logging'), if the Control Power Supply action is enabled,
this object defines the name of the managed power supply to
per… | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.119 |
| slcDevPortCfgTCPState If enabled, TCP connections to the Device Port are allowed. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.12 |
| slcDevPortCfgTokenPowerAction For Token and Data Detection (previously called 'Email
Logging'), if the Control Power Supply action is enabled,
this object defines the action to take on
slcDevPortCfgTokenPow… | column | Enumeration | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.120 |
| slcDevPortCfgTCPPort TCP Port number for TCP in connections. | column | Integer32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.13 |
| slcDevPortCfgTCPAuth If enabled, the user is required to authenticate to access
a Device Port with TCP. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.14 |
| slcDevPortCfgIP The IP Address for Telnet, SSH or TCP in to a Device Port. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.15 |
| slcDevPortCfgBaud The baud rate of the Device Port. | column | Integer32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.16 |
| slcDevPortCfgDataBits The data bits of the Device Port. | column | Integer32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.17 |
| slcDevPortCfgStopBits The stop bits of the Device Port. | column | Integer32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.18 |
| slcDevPortCfgParity The parity of the Device Port. | column | Enumeration | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.19 |
| slcDevPortCfgName The name of the Device Port. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.2 |
| slcDevPortCfgFlowControl The flow control of the Device Port. | column | Enumeration | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.20 |
| slcDevPortCfgLogins If enabled, authentication is required to access a serial
device connected to a Device Port. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.21 |
| slcDevPortCfgConnectDSR If enabled, the Device Port only establishes a connection if
DSR (Data Set Ready) transitions to an asserted state. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.22 |
| slcDevPortCfgDisconnectDSR If enabled, and a connection to a Device Port is currently
in session, the connection will be terminated if DSR (Data
Set Ready) transitions to a de-asserted state. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.23 |
| slcDevPortCfgModemState For an external modem attached to the Device Port, indicates
how the modem will be used. | column | Enumeration | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.24 |
| slcDevPortCfgModemMode For an external modem attached to the Device Port, the
mode: PPP (for Dial-in and Dial-out) and text (for Dial-in
and Dial-back). | column | Enumeration | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.25 |
| slcDevPortCfgLocalIP For PPP connections, the local IP Address - all zeros if it
should be negotiated. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.26 |
| slcDevPortCfgRemoteIP For PPP connections, the remote IP Address - all zeros if it
should be negotiated. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.27 |
| slcDevPortCfgAuth For PPP connections, the type of authentication to be used. | column | Enumeration | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.28 |
| slcDevPortCfgCHAPHost For PPP connections with CHAP authentication, the host (for
Unix) or user (for Windows) to use. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.29 |
| slcDevPortCfgDevice The device that is connected to the Device Port. The 'slp*'
and 'servertech' values are deprecated and have been replaced
by the RPM functionality. | column | Enumeration | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.3 |
| slcDevPortCfgInitScript The initialization script for an external modem. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.30 |
| slcDevPortCfgTimeout The timeout (in minutes) for text connections. A value
of 0 indicates that timeouts are disabled. | column | minutes Integer32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.31 |
| slcDevPortCfgDialoutNum The phone number to use for dial-out connections. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.32 |
| slcDevPortCfgDialoutLogin The login to use for dial-out connections. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.33 |
| slcDevPortCfgDialbackMode For dial-back connections, defines the phone number to call:
a number associated with the authenticated user, or a fixed
number associated with the Device Port. | column | Enumeration | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.34 |
| slcDevPortCfgDialbackNum The phone number to use for dial-back connections. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.35 |
| slcDevPortCfgNATState If enabled, use NAT (Network Address Translation) to allow
dial-in and dial-back users to access the network connected
to Eth1 and Eth2. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.36 |
| slcDevPortCfgLocalState If enabled, local logging is enabled for the Device Port. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.37 |
| slcDevPortCfgNFSFileState If enabled, NFS File logging is enabled for the Device Port. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.38 |
| slcDevPortCfgNFSDir The local directory of a NFS mount to use for logging. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.39 |
| slcDevPortCfgDevLogin The login used to authenticate to the device connected
to the Device Port. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.4 |
| slcDevPortCfgNFSMaxFiles The maximum number of files to use for NFS file logging. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.40 |
| slcDevPortCfgNFSMaxSize The maximum size of each file (in bytes) for NFS File logging. | column | bytes SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.41 |
| slcDevPortCfgEmailState If enabled, Token and Data Detection (previously called
'Email Logging') is enabled for the Device Port. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.42 |
| slcDevPortCfgEmailTrigger The type of trigger to use for Token and Data Detection
(previously called 'Email Logging') - number of data bytes
received, or token/character string received. | column | Enumeration | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.43 |
| slcDevPortCfgEmailByteThresh When Token and Data Detection (previously called 'Email
Logging') is configured to trigger on a data byte count,
the number of bytes required to trigger an action. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.44 |
| slcDevPortCfgEmailDelay For Token and Data Detection (previously called 'Email
Logging'), a time limit of how long the device port will
capture data after the data trigger is detected and before
closi… | column | seconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.45 |
| slcDevPortCfgEmailRestartDelay For Token and Data Detection (previously called 'Email
Logging'), the period of time, after performing the
selected actions, during which the device port will ignore
additional… | column | seconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.46 |
| slcDevPortCfgEmailTextString When Token and Data Detection (previously called 'Email
Logging') is configured to trigger on a character string,
this defines the character string that will trigger an action. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.47 |
| slcDevPortCfgEmailTo For Token and Data Detection (previously called 'Email
Logging'), if the Email action is enabled, this object
defines the list of emails to send email notification to. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.48 |
| slcDevPortCfgEmailSubject For Token and Data Detection (previously called 'Email
Logging'), if the Email action is enabled, this object
defines the subject to include with email notification. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.49 |
| slcDevPortCfgBreakSeq The character sequence for the Device Port to send a break. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.5 |
| slcDevPortCfgPCCardState If enabled, PC Card logging is enabled for the Device Port.
This value will be undefined if the SLC does not have PC Card
slots. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.50 |
| slcDevPortCfgPCCardLogTo For PC Card logging, which PC Card slot to use for logging.
This value will be undefined if the SLC does not have PC Card
slots. | column | Enumeration | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.51 |
| slcDevPortCfgPCCardMaxFiles The maximum number of files to use for PC Card logging.
This value will be undefined if the SLC does not have PC Card
slots. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.52 |
| slcDevPortCfgPCCardMaxSize The maximum size of each file (in bytes) for PC Card logging.
This value will be undefined if the SLC does not have PC Card
slots. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.53 |
| slcDevPortCfgAction Performs an action on a Device Port. A read of this object
always returns the value noAction(1). Setting this object
to zeroPortCounters(2) will reset all port counters given … | column | Enumeration | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.54 |
| slcDevPortCfgEmailSend When a trigger is received, the type of notification to send:
email, SNMP trap, or email and SNMP trap. This object is
deprecated; instead refer to slcDevPortCfgTokenAction. | column | Enumeration | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.55 |
| slcDevPortCfgBanner The banner displayed when the Device Port is connected to via
SSH or Telnet. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.56 |
| slcDevPortCfgIdleTimeout The timeout (in seconds) for dial-in and dial-on-demand PPP
connections. If no traffic is received for the PPP connection
in the time defined by the idle timeout, the PPP conne… | column | seconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.57 |
| slcDevPortCfgRestartDelay The delay (in seconds) to wait before restarting dial-out or
dial-on-demand PPP connections. | column | seconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.58 |
| slcDevPortCfgCallerIdLogging If enabled, caller id logging is enabled for a modem dial-in
connection. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.59 |
| slcDevPortCfgTelnetState If enabled, Telnet connections to the Device Port are allowed. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.6 |
| slcDevPortCfgCallerIdATCmd The modem AT command required to initiate caller id logging
by the modem. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.60 |
| slcDevPortCfgDODAuth For PPP connections that are configured for both Dial-in and
Dial-on-Demand, the type of authentication to be used for
Dial-on-Demand. | column | Enumeration | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.61 |
| slcDevPortCfgDODCHAPHost For PPP connections that are configured for both Dial-in and
Dial-on-Demand, with CHAP authentication for Dial-on-Demand,
the host (for Unix) or user (for Windows) to use. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.62 |
| slcDevPortCfgSLMLoggingState If enabled, SLM logging is enabled for the Device Port. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.63 |
| slcDevPortCfgSLMNMS The IP Addresses of up to three SNMP Network Management
Stations defined used for SLM Logging. Multiple IP Addresses
will be separated by a comma. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.64 |
| slcDevPortCfgSLMByteThresh The number of bytes required to trigger SLM logging. | column | bytes SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.65 |
| slcDevPortCfgSLMTimeFrame The time frame for SLM logging, in seconds. | column | seconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.66 |
| slcDevPortCfgWebColumns The number of columns in the Web SSH or Telnet window for
this Device Port. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.67 |
| slcDevPortCfgWebRows The number of rows in the Web SSH or Telnet window for
this Device Port. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.68 |
| slcDevPortCfgSyslogState If enabled, Syslog logging is enabled for the Device Port. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.69 |
| slcDevPortCfgTelnetPort TCP Port number for Telnet in connections. | column | Integer32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.7 |
| slcDevPortCfgHostList When slcDevPortCfgModemState is set to dialinHostList, the
name of the Host List used for Dial-in. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.70 |
| slcDevPortCfgDevLowTemp The low temperature limit, in Celsius, for the device
connected to this Device Port. If the temperature is not
applicable, 9999 will be returned. | column | Celsius SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.71 |
| slcDevPortCfgDevHighTemp The high temperature limit, in Celsius, for the device
connected to this Device Port. If the temperature is not
applicable, 9999 will be returned. | column | Celsius SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.72 |
| slcDevPortCfgDevTemperature The actual temperature, in Celsius, for the device
connected to this Device Port. If the temperature is not
applicable, an empty string will be returned. | column | Celsius OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.73 |
| slcDevPortCfgDevLowHumidity The low humidty limit, in percentage, for the device
connected to this Device Port. If the temperature is not
applicable, 9999 will be returned. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.74 |
| slcDevPortCfgDevHighHumidity The high humidty limit, in percentage, for the device
connected to this Device Port. If the temperature is not
applicable, 9999 will be returned. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.75 |
| slcDevPortCfgDevHumidity The actual humidity, in percentage, for the device
connected to this Device Port. If the temperature is not
applicable, an empty string will be returned. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.76 |
| slcDevPortCfgDevTraps If enabled, traps will be sent when one of the limits for the
device connected to this Device Port are exceeded. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.77 |
| slcDevPortCfgShowLines If enabled, upon connecting to the Device Port, a series of
characters (or lines) output to the Device Port before it
was connected to are displayed. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.78 |
| slcDevPortCfgNumberShowLines If slcDevPortCfgShowLines is enabled, the number of lines that
are displayed upon connecting to the Device Port. | column | Integer32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.79 |
| slcDevPortCfgTelnetAuth If enabled, the user is required to authenticate to access
a Device Port with Telnet. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.8 |
| slcDevPortCfgViewPortLog If enabled, upon using 'connect direct' to a Device Port,
the slcDevPortCfgPortLogSeq key sequence can be typed to
view the end of the port log for the current Device Port,
or … | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.80 |
| slcDevPortCfgPortLogSeq The character sequence to view the port log for the Device
Port. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.81 |
| slcDevPortCfgMaxDirectConnects The maximum number of direct connects at the CLI for the
Device Port. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.82 |
| slcDevPortCfgTelnetTimeout The timeout (in seconds) for Telnet connections. A value
of 0 indicates that timeouts are disabled. | column | seconds Integer32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.83 |
| slcDevPortCfgSSHTimeout The timeout (in seconds) for SSH connections. A value
of 0 indicates that timeouts are disabled. | column | seconds Integer32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.84 |
| slcDevPortCfgTCPTimeout The timeout (in seconds) for TCP connections. A value
of 0 indicates that timeouts are disabled. | column | seconds Integer32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.85 |
| slcDevPortCfgCBCPClientType When slcDevPortCfgModemState is set to cbcpClient, the
preferred type of dialback number to use for CBCP negotiation. | column | Enumeration | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.86 |
| slcDevPortCfgCBCPServerAllowNoCallback If enabled and slcDevPortCfgModemState is set to cbcpServer,
the SLC will allow the PPP peer to select the No Callback
option during CBCP negotiation. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.87 |
| slcDevPortCfgUSBState If enabled, USB logging is enabled for the Device Port. This
value will be undefined if the SLC does not have USB Ports. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.89 |
| slcDevPortCfgSSHState If enabled, SSH connections to the Device Port are allowed. | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.9 |
| slcDevPortCfgUSBLogTo For USB logging, which USB port to use for logging. This
value will be undefined if the SLC does not have USB Ports. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.90 |
| slcDevPortCfgUSBMaxFiles The maximum number of files to use for USB logging. This
value will be undefined if the SLC does not have USB Ports. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.91 |
| slcDevPortCfgUSBMaxSize The maximum size of each file (in bytes) for USB logging. This
value will be undefined if the SLC does not have USB Ports. | column | bytes SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.92 |
| slcDevPortCfgCHAPAuthLocalUsers If enabled, the local user list (login and password) is used
to validate the CHAP host and secret sent by a remote PPP
peer for CHAP authentication, instead of using the CHAP ho… | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.93 |
| slcDevPortCfgUseSites If enabled, sites (a set of site-oriented modem parameters
that can be activated by various modem-related events such
as authentication, outbound traffic for Dial-on-demand
con… | column | EnabledState | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.94 |
| slcDevPortCfgDialbackRetries When slcDevPortCfgModemState is set to dialback or cbcpServer,
specifies the number of times the SLC will retry the dial-out
portion of the dialing sequence if the first attempt… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.95 |
| slcDevPortCfgGroup The group or groups that may access the Device Port. | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.96 |
| slcDevPortCfgIPMask The network mask associated with slcDevPortCfgIPMask. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.97 |
| slcDevPortCfgDevPrompt If the device port is connected to a SLP or ServerTech CDU,
specifies the prompt that is configured for the SLP or
ServerTech CDU. This object is deprecated, and has been
repla… | column | OctetString | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.98 |
| slcDevPortCfgDevNumOutlets If the device port is connected to a ServerTech CDU, specifies
the number of outlets on the primary/master ServerTech unit.
This object is deprecated, and has been replaced by th… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.244.1.1.4.2.2.2.1.99 |