juniIpIfLoopbackUid
Juniper-IP-MIB ·
.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.11
Object
Specify the interface index of a loopback interface whose IP address
should be used when sourcing traffic on this interface. Useful for
unnumbered interfaces.
This object has been replaced by juniIpIfInheritNumUid.
Context
- MIB
- Juniper-IP-MIB
- OID
.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.11- Type
- column
- Access
- readwrite
- Status
- deprecated
- Parent
- juniIpIfEntry
- Table
- juniIpIfTable
- Siblings
- 33
Values & Constraints
Type Constraints
range: 0..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| juniIpIfIndex The ifIndex of the IP interface. When creating entries in this table,
suitable values for this object are determined by reading
juniIpNextIfIndex. | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.1 |
| juniIpIfLoopback deprecated Indicates whether the interface is a loopback type interface.
This object has been replaced by juniIpIfInheritNum. | column | Juniper-TCJuniEnable | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.10 |
| juniIpIfDebounceTime Specifies the time in milliseconds that a layer 2 interface must remain
in a state before it is conveyed to the IP layer. Useful for interfaces
that experience brief outages that… | column | milliseconds Integer32 | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.12 |
| juniIpIfForwarding Enable/disable the forwarding of IP traffic to/from this interface.
This is currently only applicable to the out-of-band management port. | column | Juniper-TCJuniEnable | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.13 |
| juniIpIfForceFragmentation Force the fragmentation of all IP packets greater than the interface
MTU even if the DF bit is set. | column | Juniper-TCJuniEnable | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.14 |
| juniIpIfSharesLowerUid Identifies the interface as sharing a lower interface with another
interface vs owning it outright. | column | Juniper-TCJuniEnable | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.15 |
| juniIpIfFilterOptions Bit mask to configure the interface to filter packets with IP header
options. Currently, either no bits or all bits may be set. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.16 |
| juniIpIfName Specify the IP interface discriminator for an IP interface not attached
to a layer 2 interface with a specific location. | column | OctetString | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.17 |
| juniIpIfArpTimeout Specify the ARP timeout for this interface in seconds. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.18 |
| juniIpIfAdminSpeed Set an administrative speed for the interface that overrides the speed
learned from the lower layer. A value of 0 indicates no speed is
specified. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.19 |
| juniIpIfRowStatus Controls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy
… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.2 |
| juniIpIfMultipathMode Configure the mode this interface should use when forwarding equal-cost
multipath traffic. | column | Enumeration | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.20 |
| juniIpIfSharedNhAddr The IP address of either a direct or indirect next-hop toward which
this shared interface should point. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.21 |
| juniIpIfSharedNhRouterId The identifier for the domain of a virtual router in which the
juniIpIfSharedNhAddr should be resolved. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.22 |
| juniIpIfPrimaryIpAddress The IP address of the primary IP network on an interface. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.23 |
| juniIpIfPrimaryIpMask The IP address mask of the primary IP network on an interface. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.24 |
| juniIpIfOperDebounceTime Indicates the operational time in milliseconds that a layer2 interface
must remain in a state before it is conveyed to the IP layer. Useful
for interfaces that experience brief o… | column | milliseconds Integer32 | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.25 |
| juniIpIfRouterIndex The index or ID of the router. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.26 |
| juniIpIfInheritNum Indicates whether this numbered interface is referenced by unnumbered
interfaces. | column | Juniper-TCJuniEnable | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.27 |
| juniIpIfInheritNumUid Specify the interface index of a numbered interface whose IP address
should be used when sourcing traffic on this interface. Useful for
unnumbered interfaces. | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.28 |
| juniIpIfAnalyzerMode Used to set the interface to analyzer mode. When enabled(1), all IP
packets entering this interface and all non-mirror IP packets leaving
this interface will be dropped. The val… | column | Enumeration | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.29 |
| juniIpIfLowerIfIndex The ifIndex of a media interface over which this IP interface is to be
layered. A value of zero is used when juniIpIfType is specified to be
loopback(4) or null(5). | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.3 |
| juniIpIfAutoConfigure When enabled, IP subscriber interfaces are created dynamically based on
any attributes defined in the service-profile and the rules associated
with the DCM profile selected for th… | column | Juniper-TCJuniEnable | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.30 |
| juniIpIfTcpMss Configures TCP MSS value for an IP interface. When configured, MSS
value of TCP SYN packets received or transmitted on the interface will
be compared with the configured value an… | column | Integer32 | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.31 |
| juniIpIfInitSeqPrefOper Indicates the operational warm-restart replay initial sequence
preference value for an IP interface. Following an HA SRP switchover,
high-preference (value 1) IP interfaces are r… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.32 |
| juniIpIfInitSeqPrefAdmin Configures the warm-restart replay initial sequence preference value
for an IP interface. See the juniIpIfInitSeqPrefOper description for more
information. | column | Unsigned32 | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.33 |
| juniIpIfArpSpoofCheck When enabled, IP ARP spoof checking is performed on ARP packets
received on the IP interface. | column | Juniper-TCJuniEnable | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.34 |
| juniIpIfType The type of network interface. | column | Enumeration | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.4 |
| juniIpIfTypeId A numerical distinguisher relevant for the loopback and null IP
interface types.
loopback Must be unique for all IP interfaces of this type.
null Must be unique … | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.5 |
| juniIpIfSAValidationEnable Enable/disable source address validation on this IP network interface. | column | Juniper-TCJuniEnable | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.6 |
| juniIpIfCreationType Specify if the interface was created due to static configuration or due
to some dynamic event. Dynamic interfaces are not stored in NVS. | column | Enumeration | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.7 |
| juniIpIfProfileId Identified the profile used when creating a dynamic interface. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.8 |
| juniIpIfAlwaysUp When enabled, the interface is determined to be up regardless of the
state of any lower layer interfaces. | column | Juniper-TCJuniEnable | .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.9 |