juniIpIfInitSeqPrefOper

Juniper-IP-MIB · .1.3.6.1.4.1.4874.2.2.12.1.1.2.1.32
MIB view Table view

Object

column SNMPv2-SMIUnsigned32 
Indicates the operational warm-restart replay initial sequence
preference value for an IP interface.  Following an HA SRP switchover,
high-preference (value 1) IP interfaces are replayed first, followed by
static routes, and then low-preference (value 0) IP interfaces.  This
allows static routes that are dependent on high-preference interfaces to
be resolved and routing protocols to exchange information with peers
over high-preference interfaces before low-preference interfaces are
replayed.  An IP interface is designated as high-preference either (1)
implicitly by configuring an IGP or PIM protocol on that interface, or
(2) explicitly by juniIpIfInitSeqPrefAdmin (or CLI) configuration.

Context

MIB
Juniper-IP-MIB
OID
.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.32
Type
column
Access
readonly
Status
current
Parent
juniIpIfEntry
Table
juniIpIfTable
Siblings
33

Syntax

SNMPv2-SMIUnsigned32
Source
SNMPv2-SMIUnsigned32
Base type
Unsigned32

Values & Constraints

Type Constraints
range: 0..4294967295

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
juniIpIfIndex
The ifIndex of the IP interface. When creating entries in this table, suitable values for this object are determined by reading juniIpNextIfIndex.
columnIF-MIBInterfaceIndex.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.1
juniIpIfLoopback deprecated
Indicates whether the interface is a loopback type interface. This object has been replaced by juniIpIfInheritNum.
columnJuniper-TCJuniEnable.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.10
juniIpIfLoopbackUid deprecated
Specify the interface index of a loopback interface whose IP address should be used when sourcing traffic on this interface. Useful for unnumbered interfaces. This…
columnIF-MIBInterfaceIndexOrZero.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.11
juniIpIfDebounceTime
Specifies the time in milliseconds that a layer 2 interface must remain in a state before it is conveyed to the IP layer. Useful for interfaces that experience brief outages that…
columnmilliseconds Integer32.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.12
juniIpIfForwarding
Enable/disable the forwarding of IP traffic to/from this interface. This is currently only applicable to the out-of-band management port.
columnJuniper-TCJuniEnable.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.13
juniIpIfForceFragmentation
Force the fragmentation of all IP packets greater than the interface MTU even if the DF bit is set.
columnJuniper-TCJuniEnable.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.14
juniIpIfSharesLowerUid
Identifies the interface as sharing a lower interface with another interface vs owning it outright.
columnJuniper-TCJuniEnable.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.15
juniIpIfFilterOptions
Bit mask to configure the interface to filter packets with IP header options. Currently, either no bits or all bits may be set.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.16
juniIpIfName
Specify the IP interface discriminator for an IP interface not attached to a layer 2 interface with a specific location.
columnOctetString.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.17
juniIpIfArpTimeout
Specify the ARP timeout for this interface in seconds.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.18
juniIpIfAdminSpeed
Set an administrative speed for the interface that overrides the speed learned from the lower layer. A value of 0 indicates no speed is specified.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.19
juniIpIfRowStatus
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy …
columnSNMPv2-TCRowStatus.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.2
juniIpIfMultipathMode
Configure the mode this interface should use when forwarding equal-cost multipath traffic.
columnEnumeration.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.20
juniIpIfSharedNhAddr
The IP address of either a direct or indirect next-hop toward which this shared interface should point.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.21
juniIpIfSharedNhRouterId
The identifier for the domain of a virtual router in which the juniIpIfSharedNhAddr should be resolved.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.22
juniIpIfPrimaryIpAddress
The IP address of the primary IP network on an interface.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.23
juniIpIfPrimaryIpMask
The IP address mask of the primary IP network on an interface.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.24
juniIpIfOperDebounceTime
Indicates the operational time in milliseconds that a layer2 interface must remain in a state before it is conveyed to the IP layer. Useful for interfaces that experience brief o…
columnmilliseconds Integer32.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.25
juniIpIfRouterIndex
The index or ID of the router.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.26
juniIpIfInheritNum
Indicates whether this numbered interface is referenced by unnumbered interfaces.
columnJuniper-TCJuniEnable.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.27
juniIpIfInheritNumUid
Specify the interface index of a numbered interface whose IP address should be used when sourcing traffic on this interface. Useful for unnumbered interfaces.
columnIF-MIBInterfaceIndexOrZero.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.28
juniIpIfAnalyzerMode
Used to set the interface to analyzer mode. When enabled(1), all IP packets entering this interface and all non-mirror IP packets leaving this interface will be dropped. The val…
columnEnumeration.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.29
juniIpIfLowerIfIndex
The ifIndex of a media interface over which this IP interface is to be layered. A value of zero is used when juniIpIfType is specified to be loopback(4) or null(5).
columnIF-MIBInterfaceIndexOrZero.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.3
juniIpIfAutoConfigure
When enabled, IP subscriber interfaces are created dynamically based on any attributes defined in the service-profile and the rules associated with the DCM profile selected for th…
columnJuniper-TCJuniEnable.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.30
juniIpIfTcpMss
Configures TCP MSS value for an IP interface. When configured, MSS value of TCP SYN packets received or transmitted on the interface will be compared with the configured value an…
columnInteger32.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.31
juniIpIfInitSeqPrefAdmin
Configures the warm-restart replay initial sequence preference value for an IP interface. See the juniIpIfInitSeqPrefOper description for more information.
columnUnsigned32.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.33
juniIpIfArpSpoofCheck
When enabled, IP ARP spoof checking is performed on ARP packets received on the IP interface.
columnJuniper-TCJuniEnable.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.34
juniIpIfType
The type of network interface.
columnEnumeration.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.4
juniIpIfTypeId
A numerical distinguisher relevant for the loopback and null IP interface types. loopback Must be unique for all IP interfaces of this type. null Must be unique …
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.5
juniIpIfSAValidationEnable
Enable/disable source address validation on this IP network interface.
columnJuniper-TCJuniEnable.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.6
juniIpIfCreationType
Specify if the interface was created due to static configuration or due to some dynamic event. Dynamic interfaces are not stored in NVS.
columnEnumeration.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.7
juniIpIfProfileId
Identified the profile used when creating a dynamic interface.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.8
juniIpIfAlwaysUp
When enabled, the interface is determined to be up regardless of the state of any lower layer interfaces.
columnJuniper-TCJuniEnable.1.3.6.1.4.1.4874.2.2.12.1.1.2.1.9