jnxoptIfODUkNimDirectionality
JNX-OPT-IF-MIB ·
.1.3.6.1.4.1.2636.3.73.1.1.8.4.1.1
Object
column
JnxoptIfSinkOrSource
Specifies the monitor point for the ODUk Path non-intrusive monitoring function. The value source(2) is not allowed if the corresponding instance of jnxoptIfODUkDirectionality has the value sink(1), and the value sink(1) is not allowed if the corresponding instance of jnxoptIfODUkDirectionality has the value source(2). Either the value sink(1) or source(2) is allowed if the corresponding instance of jnxoptIfODUkDirectionality has the value bidirectional(3). The value sink(1) means monitoring at the sink direction path signal of the ODUk CTP. The value source(2) means monitoring at the source direction path signal of the ODUk CTP. Monitoring the source direction of an ODUk CTP is necessary in those cases where the ODUk CTP is at an SNCP (Subnetwork Connection Protection) end (e.g., see Figure I.1.2/G.874.1). If one would like to get the performance of the protected connection, one cannot use the NIM function at both ODUk CTP sinks (before the matrix), instead one should monitor the signal at the source ODUk CTP after the matrix.
Context
- MIB
- JNX-OPT-IF-MIB
- OID
.1.3.6.1.4.1.2636.3.73.1.1.8.4.1.1- Type
- column
- Access
- noaccess
- Status
- current
- Parent
- jnxoptIfODUkNimConfigEntry
- Table
- jnxoptIfODUkNimConfigTable
- Siblings
- 9
Syntax
JnxoptIfSinkOrSource
- Source
- JnxoptIfSinkOrSource
- Base type
Enumeration
Values & Constraints
Type Values
1 | sink |
2 | source |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| jnxoptIfODUkNimRowStatus This columnar object is used for creating and deleting
a conceptual row of the jnxoptIfODUkNim config table.
It is used to model the activateNim and deactivateNim
operations of… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.2636.3.73.1.1.8.4.1.10 |
| jnxoptIfODUkNimDAPIExpected The DAPI expected by the receiver.
This object has no effect if jnxoptIfODUkNimTIMDetMode has
the value off(1) or sapi(3). | column | JnxoptIfExDAPI | .1.3.6.1.4.1.2636.3.73.1.1.8.4.1.2 |
| jnxoptIfODUkNimSAPIExpected The SAPI expected by the receiver.
This object has no effect if jnxoptIfODUkNimTIMDetMode has
the value off(1) or dapi(2). | column | JnxoptIfExSAPI | .1.3.6.1.4.1.2636.3.73.1.1.8.4.1.3 |
| jnxoptIfODUkNimTraceIdentifierAccepted The actual trace identifier accepted. The value of
this object is unspecified if jnxoptIfODUkNimCurrentStatus
has any of the bit positions oci(0), lck(1), or ssf(5)
set or if j… | column | JnxoptIfAcTI | .1.3.6.1.4.1.2636.3.73.1.1.8.4.1.4 |
| jnxoptIfODUkNimTIMDetMode Indicates the mode of the Trace Identifier Mismatch (TIM)
Detection function. | column | JnxoptIfTIMDetMode | .1.3.6.1.4.1.2636.3.73.1.1.8.4.1.5 |
| jnxoptIfODUkNimTIMActEnabled Indicates whether the Trace Identifier Mismatch (TIM)
Consequent Action function is enabled. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2636.3.73.1.1.8.4.1.6 |
| jnxoptIfODUkNimDEGThr Indicates the threshold level for declaring a performance
monitoring (PM) Second to be bad. A PM Second is declared bad
if the percentage of detected errored blocks in that seco… | column | percentage JnxoptIfDEGThr | .1.3.6.1.4.1.2636.3.73.1.1.8.4.1.7 |
| jnxoptIfODUkNimDEGM Indicates the threshold level for declaring a Degraded Signal
defect (dDEG). A dDEG shall be declared if jnxoptIfODUkNimDEGM
consecutive bad PM Seconds are detected. | column | JnxoptIfDEGM | .1.3.6.1.4.1.2636.3.73.1.1.8.4.1.8 |
| jnxoptIfODUkNimCurrentStatus Indicates the defect condition of the entity, if
any. The value of this object is unspecified if
jnxoptIfODUkNimRowStatus has any value other than
active(1). | column | Bits | .1.3.6.1.4.1.2636.3.73.1.1.8.4.1.9 |