npPortUsbDesiredMode

JETDIRECT3-MIB · .1.3.6.1.4.1.11.2.4.3.13.12

MIB view Table view

Object

scalar r/w Enumeration

The desired operating mode of the USB interface to this device.
JetDirect normally uses the best interface the device supports.
Setting this object limits the device to a simpler interface when
the more complex interface does not work with JetDirect.
          
  automatic      = use best available protocol
  unidirectional = limit to forward data only (USB class 7.1.1)
  bidirectional  = limit to simple forward and reverse data (7.1.2)
  mlc            = limit to HP-MLC protocol (USB class 7.1.2+)

Context

MIB: JETDIRECT3-MIB
OID: .1.3.6.1.4.1.11.2.4.3.13.12
Type: scalar
Access: readwrite
Status: current
Parent: npPort
Siblings: 15

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	automatic
`2`	unidirectional
`3`	bidirectional
`4`	mlc

Object Constraints

range: 0-46

Related Objects

Sibling Objects

Object	Type	Syntax	OID
npPortNumPorts The number of peripheral interfaces supported by this device.	scalar	Integer32	`.1.3.6.1.4.1.11.2.4.3.13.1`
npPortSetEcpHostRecTimer Takes the 16 bit value and applies it to the Host Recovery Time Register. The default value is 0. EX-ONLY	scalar	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.11.2.4.3.13.10`
npPortSetIoFlags2 Sets and/or disables IO flags. Reset value of 0. EX-ONLY	scalar	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.11.2.4.3.13.11`
npPortUsbCurrentMode The current operating mode of the USB interface to this device. unknown = unknown or no device connected unidirectional = forward data only (USB class 7.1.1) bid…	scalar	Enumeration	`.1.3.6.1.4.1.11.2.4.3.13.13`
npPortUsbProduct The product string (if any) returned by the current USB device on this port.	scalar	DisplayString128	`.1.3.6.1.4.1.11.2.4.3.13.14`
npPortUsbManufacturer The manufacturer string (if any) returned by the current USB device on this port.	scalar	DisplayString128	`.1.3.6.1.4.1.11.2.4.3.13.15`
npPortUsbSerialNumber The serial number string (if any) returned by the current USB device on this port.	scalar	DisplayString128	`.1.3.6.1.4.1.11.2.4.3.13.16`
npPortType The type of the peripheral interface. A parallel port will return the specific protocol currently in use. If the parallel port is disconnected it will return parallel(4).	scalar	Enumeration	`.1.3.6.1.4.1.11.2.4.3.13.2`
npPortDesiredMode The desired (remotely specified) operating mode of the parallel port. The following map is used to determine mode availability and provides the definition for each mode…	scalar	Enumeration	`.1.3.6.1.4.1.11.2.4.3.13.3`
npPortCentronicsHandshaking The handshaking to be used in sending data over the parallel port. EX-ONLY	scalar	Enumeration	`.1.3.6.1.4.1.11.2.4.3.13.4`
npPortStatusLines The state of the centronics status lines from the peripheral. The value is a bit mask. Bit Value Signal 0 0x01 nACK 1 0x02 2 0x04 3 …	scalar	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.11.2.4.3.13.5`
npPortMaxModeAvaliable The maximum available parallel mode by which the print-server may connect to an attached peripheral. This is a function of the the available hardware and firmware capabilities. …	scalar	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.11.2.4.3.13.6`
npPortBidiPollRate Poll rate for bi-directional data. Range is 10 to 100 seconds. Defaults to 40 seconds. EX-ONLY	scalar	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.11.2.4.3.13.7`
npPortSetCentronicsTiming Takes the 16 bit value and applies it to the centronics timing register. The default value is 0 and is not applied to the centronics timing register. EX-ONLY	scalar	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.11.2.4.3.13.8`
npPortSetIoFlags Sets and/or disables IO flags. Reset value of 0. EX-ONLY	scalar	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.11.2.4.3.13.9`