npPortCentronicsHandshaking
JETDIRECT3-MIB ·
.1.3.6.1.4.1.11.2.4.3.13.4
Object
scalar
r/w
Enumeration
The handshaking to be used in sending data over the parallel port. EX-ONLY
Context
- MIB
- JETDIRECT3-MIB
- OID
.1.3.6.1.4.1.11.2.4.3.13.4- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- npPort
- Siblings
- 15
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | nack-and-busy |
2 | nack-only |
3 | busy-only |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| npPortNumPorts The number of peripheral interfaces supported by this device. | scalar | Integer32 | .1.3.6.1.4.1.11.2.4.3.13.1 |
| npPortSetEcpHostRecTimer Takes the 16 bit value and applies
it to the Host Recovery Time Register.
The default value is 0. EX-ONLY | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.4.3.13.10 |
| npPortSetIoFlags2 Sets and/or disables IO flags.
Reset value of 0. EX-ONLY | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.4.3.13.11 |
| npPortUsbDesiredMode The desired operating mode of the USB interface to this device.
JetDirect normally uses the best interface the device supports.
Setting this object limits the device to a simpler … | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.13.12 |
| npPortUsbCurrentMode The current operating mode of the USB interface to this device.
unknown = unknown or no device connected
unidirectional = forward data only (USB class 7.1.1)
bid… | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.13.13 |
| npPortUsbProduct The product string (if any) returned by the current USB device
on this port. | scalar | DisplayString128 | .1.3.6.1.4.1.11.2.4.3.13.14 |
| npPortUsbManufacturer The manufacturer string (if any) returned by the current USB device
on this port. | scalar | DisplayString128 | .1.3.6.1.4.1.11.2.4.3.13.15 |
| npPortUsbSerialNumber The serial number string (if any) returned by the current USB device
on this port. | scalar | DisplayString128 | .1.3.6.1.4.1.11.2.4.3.13.16 |
| npPortType The type of the peripheral interface. A parallel port will return
the specific protocol currently in use. If the parallel port is
disconnected it will return parallel(4). | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.13.2 |
| npPortDesiredMode The desired (remotely specified) operating mode of the parallel port.
The following map is used to determine mode availability and provides
the definition for each mode… | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.13.3 |
| npPortStatusLines The state of the centronics status lines from the peripheral. The
value is a bit mask.
Bit Value Signal
0 0x01 nACK
1 0x02
2 0x04
3 … | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.4.3.13.5 |
| npPortMaxModeAvaliable The maximum available parallel mode by which the print-server may
connect to an attached peripheral. This is a function of the
the available hardware and firmware capabilities. … | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.4.3.13.6 |
| npPortBidiPollRate Poll rate for bi-directional data.
Range is 10 to 100 seconds.
Defaults to 40 seconds. EX-ONLY | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.4.3.13.7 |
| npPortSetCentronicsTiming Takes the 16 bit value and applies
it to the centronics timing register.
The default value is 0 and is not
applied to the centronics timing
register. EX-ONLY | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.4.3.13.8 |
| npPortSetIoFlags Sets and/or disables IO flags.
Reset value of 0. EX-ONLY | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.4.3.13.9 |