npCtlWiFiDirectHidePassphrase
JETDIRECT3-MIB ·
.1.3.6.1.4.1.11.2.4.3.7.58
Object
scalar
r/w
Enumeration
This controls display of the Wireless passphrase on configuration reports/pages or on the control panel. Show = 0 Hide = 1 This object also controls whether or not the passphrase is included in the NFC record. Hide (1) only takes effect when npCfgWiFiDirectConnectionSecurity is set to Advanced
Context
- MIB
- JETDIRECT3-MIB
- OID
.1.3.6.1.4.1.11.2.4.3.7.58- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- npCtl
- Siblings
- 38
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | show |
1 | hide |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| npCtlReconfigIP The IP address of the last node to request a reconfig
of the card. This value is preserved across a reconfig. | scalar | RFC1155-SMIIpAddress | .1.3.6.1.4.1.11.2.4.3.7.1 |
| npCtlStatusPageLang This object specifies the PDL used to print the status page.
EX ONLY | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.7.10 |
| npCtlPrintStatusPage Writing any value to this object causes the device to print
a status page. EX ONLY | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.4.3.7.11 |
| npCtlCrcControl This object controls and manages the collection of crc data
for paperless print testing. | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.7.13 |
| npCtlSNMPEnableDisable 0 - disable SNMP
Disable the SNMP protocol on the JetDirect device.
Once SNMP is disabled it will not be
possible to enable SNMP via another SNMP request, or
enabled while this o… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.4.3.7.14 |
| npCtlStatusPageLangMask This object specifies the Page Description
Language (PDL) used to print the status page.
It is a bit mask as follows:
pcl = 1
ascii = 2
postscr… | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.7.15 |
| npCtlBpDisableLCB This object will disable (0) or enable (1) LCB (Logical Channel Break). | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.4.3.7.16 |
| npCtlTknobCommandRequest A tuning knob command is processed when
this object is set with specific requests.
Any response from the tuning knob command
is made available via npCtlTknobCommandResponse. | scalar | OctetString | .1.3.6.1.4.1.11.2.4.3.7.17 |
| npCtlTknobCommandResponse A tuning knob command is processed when
npCtlTknobCommandRequest is set with specific requests.
Any response from the tuning knob command
is made available via this object. | scalar | OctetString | .1.3.6.1.4.1.11.2.4.3.7.18 |
| npCtlTelnet Configure Telnet service.
(0) = Telnet disabled
(1) = Telnet enabled | scalar | Integer32 | .1.3.6.1.4.1.11.2.4.3.7.19 |
| npCtlReconfigPort The port of the last node to request a reconfig of the
card. This value is preserved across a reconfig. | scalar | Integer32 | .1.3.6.1.4.1.11.2.4.3.7.2 |
| npCtlSLP Configure Service Location Protocol (SLP) service.
(0) = SLP disabled
(1) = SLP enabled | scalar | Integer32 | .1.3.6.1.4.1.11.2.4.3.7.21 |
| npCtlLPD Configure Line Printer Daemon Protocol (LPD) service.
(0) = LPD disabled
(1) = LPD enabled | scalar | Integer32 | .1.3.6.1.4.1.11.2.4.3.7.22 |
| npCtl9100 Configure TCP port 9100 printing.
(0) = port 9100 printing disabled
(1) = port 9100 printing enabled | scalar | Integer32 | .1.3.6.1.4.1.11.2.4.3.7.24 |
| npCtlSysLog Configure Syslog service.
(0) = Syslog service disabled
(1) = Syslog service enabled
Enabled by default. | scalar | Integer32 | .1.3.6.1.4.1.11.2.4.3.7.26 |
| npCtlSnmpVersionAccess Manages an SNMP version's read and write access to the MIB. | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.7.27 |
| npCtlSnmpV3InitAccount Used to create initial SNMPv3 account. The following rules apply:
0 = clear init account, only if previously 0.
4 = Block init account, only cold reset will clear or u… | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.7.28 |
| npCtlBonjour Configure Multicast Domain Name Service.
(0) = Bonjour disabled
(1) = Bonjour enabled | scalar | Integer32 | .1.3.6.1.4.1.11.2.4.3.7.29 |
| npCtlReconfigTime The time (in hundredths of a second) since the last
time the card was reconfigured. | scalar | RFC1155-SMITimeTicks | .1.3.6.1.4.1.11.2.4.3.7.3 |
| npCtlNetworkConnectionMode This object controls the selection of the active network
interface used for communication. This is applicable to
products supporting dual wired and wireless network interfaces | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.7.32 |
| npCtlIPSecurityPolicy Disable IP Security (IPSec) or Firewall. Only disabling is allowed. | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.7.34 |
| npCtlWSDiscovery Web Services Discovery enable/disable. | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.7.36 |
| npCtlWSPrint Web Services Print enable/disable. | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.7.37 |
| npCtlLLMNR Link-Local Multicast Name Resolution( LLMNR ) enable/disable. | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.7.38 |
| npCtlCloseIP The IP address of the last node to request a close of
the peripheral data connection on the card. This
value is cleared on a reconfig. | scalar | RFC1155-SMIIpAddress | .1.3.6.1.4.1.11.2.4.3.7.4 |
| npCtlFpDot11WirelessState Use for enabling and disabling Wireless Radio.
The following values are defined:
Disable = 0
Enable = 1
Default = 1(Enabled) | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.7.47 |
| npCtlClosePort The port of the last node to request a close of the
peripheral data connection on the card. This
value is cleared on a reconfig. | scalar | Integer32 | .1.3.6.1.4.1.11.2.4.3.7.5 |
| npCtlWiFiDirectSSIDBroadcast This is used to allow or hide broadcasting of the SSID (Network name).
Allowed(Default) = 1
Not Allowed = 0
Not Allowed (0) only takes effect when npCfgWiFiDirectConnectionSe… | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.7.57 |
| npCtlWiFiDirectHideSsid This controls display of the network name (SSID) on configuration
reports/pages or on the control panel.
Show = 0
Hide = 1
Hide (1) only takes effect when npCfgWifiDirectConnectio… | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.7.59 |
| npCtlImageDump obsolete Writing a one (1) to this variable causes the card to dump
its RAM image into a file using TFTP. The file is dumped
onto the BOOTP server machine whose IP address is in the MIB
v… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.4.3.7.6 |
| npCtlAirPrintStatus Use to Enabled/Disabled AirPrint functionality.
Disable = 0
Enable(Default) = 1 | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.7.68 |
| npCtlCloseConnection Writing a one (1) to this variable causes the card to close
the current peripheral data connection | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.4.3.7.7 |
| npCtlAllowRFC5746TLS-SSLCompatibilityMode Added to support RFC-5746.
This OID can be use to enable/disable legacy SSL renegotiation.
Disable = 0
Enable(Default) = 1 | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.7.70 |
| npCtlWiFiDirectState Configure 802.11 Wireless/Wi-Fi Direct functionality
0 = Wireless/Wi-Fi Direct is disabled
1 = Wireless/Wi-Fi Direct is enabled | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.7.74 |
| npCtlAirScan Used to Enable/Disable the AirScan service.
Disable = 0
Enable (Default) = 1 | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.7.79 |
| npCtlReconfig Writing any value to this variable causes the card to
reconfigure itself by doing the BOOTP/TFTP configuration
activity. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.4.3.7.8 |
| npCtlAirFax Used to Enable/Disable the AirFax service.
Disable = 0
Enable (Default) = 1 | scalar | Enumeration | .1.3.6.1.4.1.11.2.4.3.7.80 |
| npCtlProtocolSet This is a 4 byte integer value. The least significant bytes
represent the protocols on the card. A value of '1' indicates
a protocol that is enabled. A value of '0' indicates a… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.4.3.7.9 |