npCtlStatusPageLangMask

JETDIRECT3-MIB · .1.3.6.1.4.1.11.2.4.3.7.15
MIB view Table view

Object

scalar r/w Enumeration 
This object specifies the Page Description 
Language (PDL) used to print the status page. 
It is a bit mask as follows:
          
   pcl        =  1
   ascii      =  2
   postscript =  4
   hpgl2      =  8
   all        = 15
          
Although the user may select a specific PDL it doesn't 
guarantee that the status page will actually be
printed as selected, as the actual PDL used depends 
on the PDL capability of the printer. PDL values 
may also be set via npCtlStatusPageLang, by telnet, 
by the embedded web server on the JetDirect device, 
by the front panel of some printers, or by using
the select button on the EX box. PDL values set via
these alternate methods will be reflected by this object
upon a read. 
          
This object is intended as an eventual replacement for 
npCtlStatusPageLang.

Context

MIB
JETDIRECT3-MIB
OID
.1.3.6.1.4.1.11.2.4.3.7.15
Type
scalar
Access
readwrite
Status
current
Parent
npCtl
Siblings
38

Syntax

Enumeration

Values & Constraints

Enumerated Values
1pcl
2ascii
3pcl-ascii
4postscript
5pcl-postscript
6ascii-postscript
7pcl-ascii-postscript
8hpgl2
9pcl-hpgl2
10ascii-hpgl2
11pcl-ascii-hpgl2
12postscript-hpgl2
13pcl-postscript-hpgl2
14ascii-postscript-hpgl2
15all

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
npCtlReconfigIP
The IP address of the last node to request a reconfig of the card. This value is preserved across a reconfig.
scalarRFC1155-SMIIpAddress.1.3.6.1.4.1.11.2.4.3.7.1
npCtlStatusPageLang
This object specifies the PDL used to print the status page. EX ONLY
scalarEnumeration.1.3.6.1.4.1.11.2.4.3.7.10
npCtlPrintStatusPage
Writing any value to this object causes the device to print a status page. EX ONLY
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.11.2.4.3.7.11
npCtlCrcControl
This object controls and manages the collection of crc data for paperless print testing.
scalarEnumeration.1.3.6.1.4.1.11.2.4.3.7.13
npCtlSNMPEnableDisable
0 - disable SNMP Disable the SNMP protocol on the JetDirect device. Once SNMP is disabled it will not be possible to enable SNMP via another SNMP request, or enabled while this o…
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.11.2.4.3.7.14
npCtlBpDisableLCB
This object will disable (0) or enable (1) LCB (Logical Channel Break).
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.11.2.4.3.7.16
npCtlTknobCommandRequest
A tuning knob command is processed when this object is set with specific requests. Any response from the tuning knob command is made available via npCtlTknobCommandResponse.
scalarOctetString.1.3.6.1.4.1.11.2.4.3.7.17
npCtlTknobCommandResponse
A tuning knob command is processed when npCtlTknobCommandRequest is set with specific requests. Any response from the tuning knob command is made available via this object.
scalarOctetString.1.3.6.1.4.1.11.2.4.3.7.18
npCtlTelnet
Configure Telnet service. (0) = Telnet disabled (1) = Telnet enabled
scalarInteger32.1.3.6.1.4.1.11.2.4.3.7.19
npCtlReconfigPort
The port of the last node to request a reconfig of the card. This value is preserved across a reconfig.
scalarInteger32.1.3.6.1.4.1.11.2.4.3.7.2
npCtlSLP
Configure Service Location Protocol (SLP) service. (0) = SLP disabled (1) = SLP enabled
scalarInteger32.1.3.6.1.4.1.11.2.4.3.7.21
npCtlLPD
Configure Line Printer Daemon Protocol (LPD) service. (0) = LPD disabled (1) = LPD enabled
scalarInteger32.1.3.6.1.4.1.11.2.4.3.7.22
npCtl9100
Configure TCP port 9100 printing. (0) = port 9100 printing disabled (1) = port 9100 printing enabled
scalarInteger32.1.3.6.1.4.1.11.2.4.3.7.24
npCtlSysLog
Configure Syslog service. (0) = Syslog service disabled (1) = Syslog service enabled Enabled by default.
scalarInteger32.1.3.6.1.4.1.11.2.4.3.7.26
npCtlSnmpVersionAccess
Manages an SNMP version's read and write access to the MIB.
scalarEnumeration.1.3.6.1.4.1.11.2.4.3.7.27
npCtlSnmpV3InitAccount
Used to create initial SNMPv3 account. The following rules apply: 0 = clear init account, only if previously 0. 4 = Block init account, only cold reset will clear or u…
scalarEnumeration.1.3.6.1.4.1.11.2.4.3.7.28
npCtlBonjour
Configure Multicast Domain Name Service. (0) = Bonjour disabled (1) = Bonjour enabled
scalarInteger32.1.3.6.1.4.1.11.2.4.3.7.29
npCtlReconfigTime
The time (in hundredths of a second) since the last time the card was reconfigured.
scalarRFC1155-SMITimeTicks.1.3.6.1.4.1.11.2.4.3.7.3
npCtlNetworkConnectionMode
This object controls the selection of the active network interface used for communication. This is applicable to products supporting dual wired and wireless network interfaces
scalarEnumeration.1.3.6.1.4.1.11.2.4.3.7.32
npCtlIPSecurityPolicy
Disable IP Security (IPSec) or Firewall. Only disabling is allowed.
scalarEnumeration.1.3.6.1.4.1.11.2.4.3.7.34
npCtlWSDiscovery
Web Services Discovery enable/disable.
scalarEnumeration.1.3.6.1.4.1.11.2.4.3.7.36
npCtlWSPrint
Web Services Print enable/disable.
scalarEnumeration.1.3.6.1.4.1.11.2.4.3.7.37
npCtlLLMNR
Link-Local Multicast Name Resolution( LLMNR ) enable/disable.
scalarEnumeration.1.3.6.1.4.1.11.2.4.3.7.38
npCtlCloseIP
The IP address of the last node to request a close of the peripheral data connection on the card. This value is cleared on a reconfig.
scalarRFC1155-SMIIpAddress.1.3.6.1.4.1.11.2.4.3.7.4
npCtlFpDot11WirelessState
Use for enabling and disabling Wireless Radio. The following values are defined: Disable = 0 Enable = 1 Default = 1(Enabled)
scalarEnumeration.1.3.6.1.4.1.11.2.4.3.7.47
npCtlClosePort
The port of the last node to request a close of the peripheral data connection on the card. This value is cleared on a reconfig.
scalarInteger32.1.3.6.1.4.1.11.2.4.3.7.5
npCtlWiFiDirectSSIDBroadcast
This is used to allow or hide broadcasting of the SSID (Network name). Allowed(Default) = 1 Not Allowed = 0 Not Allowed (0) only takes effect when npCfgWiFiDirectConnectionSe…
scalarEnumeration.1.3.6.1.4.1.11.2.4.3.7.57
npCtlWiFiDirectHidePassphrase
This controls display of the Wireless passphrase on configuration reports/pages or on the control panel. Show = 0 Hide = 1 This object also controls whether or not the passphra…
scalarEnumeration.1.3.6.1.4.1.11.2.4.3.7.58
npCtlWiFiDirectHideSsid
This controls display of the network name (SSID) on configuration reports/pages or on the control panel. Show = 0 Hide = 1 Hide (1) only takes effect when npCfgWifiDirectConnectio…
scalarEnumeration.1.3.6.1.4.1.11.2.4.3.7.59
npCtlImageDump obsolete
Writing a one (1) to this variable causes the card to dump its RAM image into a file using TFTP. The file is dumped onto the BOOTP server machine whose IP address is in the MIB v…
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.11.2.4.3.7.6
npCtlAirPrintStatus
Use to Enabled/Disabled AirPrint functionality. Disable = 0 Enable(Default) = 1
scalarEnumeration.1.3.6.1.4.1.11.2.4.3.7.68
npCtlCloseConnection
Writing a one (1) to this variable causes the card to close the current peripheral data connection
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.11.2.4.3.7.7
npCtlAllowRFC5746TLS-SSLCompatibilityMode
Added to support RFC-5746. This OID can be use to enable/disable legacy SSL renegotiation. Disable = 0 Enable(Default) = 1
scalarEnumeration.1.3.6.1.4.1.11.2.4.3.7.70
npCtlWiFiDirectState
Configure 802.11 Wireless/Wi-Fi Direct functionality 0 = Wireless/Wi-Fi Direct is disabled 1 = Wireless/Wi-Fi Direct is enabled
scalarEnumeration.1.3.6.1.4.1.11.2.4.3.7.74
npCtlAirScan
Used to Enable/Disable the AirScan service. Disable = 0 Enable (Default) = 1
scalarEnumeration.1.3.6.1.4.1.11.2.4.3.7.79
npCtlReconfig
Writing any value to this variable causes the card to reconfigure itself by doing the BOOTP/TFTP configuration activity.
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.11.2.4.3.7.8
npCtlAirFax
Used to Enable/Disable the AirFax service. Disable = 0 Enable (Default) = 1
scalarEnumeration.1.3.6.1.4.1.11.2.4.3.7.80
npCtlProtocolSet
This is a 4 byte integer value. The least significant bytes represent the protocols on the card. A value of '1' indicates a protocol that is enabled. A value of '0' indicates a…
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.11.2.4.3.7.9