use2ControlDistributeVccs
IBM-LES-BUS-MIB ·
.1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.6
Object
When TRUE, proxy clients are placed on one Point-to-Multipoint Control Distribute VCC and all other clients are placed on another Point-to-Multipoint Control Distribute VCC. When FALSE, all clients are placed on a single Point-to-Multipoint Control Distribute VCC. The advantage of using two Control Distribute VCCs is that non-proxy clients are not perturbed by LE_ARP_REQUESTs for unregistered LAN Destinations (the LES answers LE_ARP_REQUESTs for registered LAN Destinations). The disadvantage is that Control Frames destined for all clients (LE_TOPOLOGY_REQUEST, LE_NARP_REQUEST, and possibly LE_ARP_RESPONSE depending upon LES-BUS-12) must be transmitted on 2 VCCs (as a related aside, note that LE_FLUSH_RESPONSEs are sent solely to the originator of the corresponding LE_FLUSH_REQUEST over the Control Direct VCC to that client).
Context
- MIB
- IBM-LES-BUS-MIB
- OID
.1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.6- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- ibmLesBusConfEntry
- Table
- ibmLesBusConfTable
- Siblings
- 25
Syntax
SNMPv2-TC-v1TruthValue
- Source
- SNMPv2-TC-v1TruthValue
- Base type
Enumeration
Values & Constraints
Type Values
1 | true |
2 | false |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| atmDevNum mandatory Identifies ATM device to be used by LES/BUS. | column | Integer32 | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.1 |
| multicastSendMaxReservedBw mandatory Defines the maximum acceptable Sustained Cell Rate (SCR)
for a Multicast Send VCC; if SCR is not specified on the
incoming call, then this parameter defines the maximum
acceptable… | column | NWAYSMSS-MIBBandwidth | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.10 |
| controlDistributeVccType mandatory Specifies type of traffic characteristics
to be associated with Control Distribute VCC(s).
Bandwidth is not reserved for best effort traffic. | column | NWAYSMSS-MIBAtmVccTrafficType | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.11 |
| controlDistributePcr mandatory Specifies the Peak Cell Rate (PCR) Traffic Parameter
for the Control Distribute VCC(s). Since the Control
Distribute is a point-to-multipoint VCC, the
specified rate applies to t… | column | NWAYSMSS-MIBBandwidth | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.12 |
| controlDistributeScr mandatory Specifies the Sustained Cell Rate (SCR) Traffic
Parameter for the Control Distribute VCC(s).
Since the Control Distribute is a point-to-multipoint
VCC, the specified rate applies … | column | NWAYSMSS-MIBBandwidth | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.13 |
| multicastForwardVccType mandatory Specifies type of traffic characteristics
to be associated with Multicast Forward VCC(s).
Bandwidth is not reserved for best effort traffic. | column | NWAYSMSS-MIBAtmVccTrafficType | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.14 |
| multicastForwardPcr mandatory Specifies the Peak Cell Rate (PCR) Traffic Parameter
for the Multicast Forward VCC(s). Since the Multicast
Multicast Forward is a point-to-multipoint
VCC, the specified rate appl… | column | NWAYSMSS-MIBBandwidth | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.15 |
| multicastForwardScr mandatory Specifies the Sustained Cell Rate (SCR) Traffic
Parameter for the Multicast Forward VCC(s). Since
the Multicast Forward is a point-to-multipoint
VCC, the specified rate applies t… | column | NWAYSMSS-MIBBandwidth | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.16 |
| validateJoinsWithLecs mandatory Specifies whether clients that attempt to join
the ELAN must be validated by the LECS. The default
value is taken from the corresponding object in the ELAN MIB,
and it overrides t… | column | SNMPv2-TC-v1TruthValue | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.17 |
| redundancyEnabled mandatory Redundancy support allows clients to be assigned to
a backup LES/BUS in the event that the primary LES/BUS
for the ELAN fails. | column | SNMPv2-TC-v1TruthValue | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.18 |
| redundancyRole mandatory Redundancy Protocol Role. Specifies whether this LES/BUS instance
is to serve as the primary or backup LES/BUS for the ELAN. This
object is only valid when redundancyEnabled is t… | column | Enumeration | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.19 |
| useBurnedInEsi mandatory Specifies whether a MAC Address burned into the ATM
device should be used as the End System Identifier
component of the LES/BUS ATM Address. | column | SNMPv2-TC-v1TruthValue | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.2 |
| redundancyAtmAddr mandatory ATM Address of Backup LES/BUS. Specifies the ATM address of the
backup LES/BUS for the ELAN. Currently, only the private
address formats defined by the ATM Forum are supported, t… | column | - | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.20 |
| bmonEnabled mandatory Enable BUS Monitor for ELAN. When TRUE, host usage of the
Broadcast and Unknown Server is monitored. Periodic sampling
is performed to provide information on the top N heaviest
… | column | SNMPv2-TC-v1TruthValue | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.21 |
| numTopMacs mandatory Number of Top MAC Addresses to Record. Specifies the number
of MACs to be recorded with the highest quantity of sampled
frames sent to the BUS in a sample interval. | column | Integer32 | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.22 |
| sampleDuration mandatory Number of seconds in each Sample Interval. Specifies the number
of seconds in each BUS Monitor sample interval. | column | Integer32 | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.23 |
| interSampleTime mandatory Minutes between start of one sample and the next sample.
Specifies the number of minutes between the start of
one BUS Monitor sample interval and the start of the
next sample inte… | column | Integer32 | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.24 |
| sampleRate mandatory Specifies the rate at which the BUS Monitor samples
frames sent to the BUS during a sample interval.
A value of 1 indicates that every frame sent to the
BUS is sampled. A value o… | column | Integer32 | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.25 |
| busMode mandatory With the Fast Bus Feature the BUS can run now run in one of
three modes:
systemBusMode(1) - Frames from BUS are buffered into system memory.
All … | column | Enumeration | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.26 |
| configuredEsi mandatory Locally Administered End System Identifier that is to be
used as the ESI component of the LES/BUS ATM Address.
If this object is used do not use the ATM Forum elanLecAtmMask.
If b… | column | NWAYSMSS-MIBAtmPrivateAddrEsi | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.3 |
| configuredSelector mandatory Specifies value to be used as Selector field component
of LES/BUS ATM Address.
If this object is used do not use the ATM Forum elanLecAtmMask.
If both are used the last object set… | column | NWAYSMSS-MIBAtmSelector | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.4 |
| leArpResponseDest mandatory When the value is ALL_CLIENTS, LE_ARP_RESPONSE
frames initiated or forwarded by the LES are
sent to all clients on the Point-to-Multipoint
Control Distribute VCC(s). When the val… | column | Enumeration | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.5 |
| use2MulticastForwardVccs mandatory When TRUE:
- proxy clients are placed on one Point-to-Multipoint
Multicast Forward VCC and all other clients are
placed on another Point-to-Multipoint Multicast
Forward VCC,… | column | SNMPv2-TC-v1TruthValue | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.7 |
| validateBestEffortPcr mandatory When false, Best Effort Control Direct or Multicast Send
VCCs will be accepted without regard to the signalled
forward Peak Cell Rate (PCR). When true, Best Effort
VCCs will be r… | column | SNMPv2-TC-v1TruthValue | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.8 |
| controlDirectMaxReservedBw mandatory Defines the maximum acceptable Sustained Cell Rate (SCR)
for a Control Direct VCC; if SCR is not specified on the
incoming call, then this parameter defines the maximum
acceptable… | column | NWAYSMSS-MIBBandwidth | .1.3.6.1.4.1.2.6.118.1.2.1.1.1.1.1.9 |