hwOspfv2SpfSchHoldIntvl
HUAWEI-OSPFV2-MIB ·
.1.3.6.1.4.1.2011.5.25.155.3.1.28
Object
column
r/w
millionSecond Integer32
This object indicates the Holdtime interval of intelligent timer for OSPF to perform the SPF calculation. After an intelligent timer is enabled, the interval for the SPF calculation is as follows: The initial interval for the SPF calculation is specified by the parameter start-interval. The interval for the SPF calculation for the nth (n>2) time is equal to hold-interval*2(n-1). When the interval specified by hold-interval*2(n-1) reaches the maximum interval specified by max-interval, OSPF performs the SPF calculation at the maximum interval for three consecutive times. Then, OSPF performs the SPF calculation at the initial interval specified by start-interval. When hwOspfv2SpfSchHoldIntvl is specified, you need also specify hwOspfv2SpfSchMaxIntvl and hwOspfv2SpfSchStartIntvl, but you cannot specify hwOspfv2SpfSchIntvlUnit or hwOspfv2SpfSchIntvlNumber. Note that -1 is not a configurable value. Instead, by set the intelligent timer to default value, it will get back to default configuration.
Context
- MIB
- HUAWEI-OSPFV2-MIB
- OID
.1.3.6.1.4.1.2011.5.25.155.3.1.28- Type
- column
- Access
- readwrite
- Status
- current
- Units
- millionSecond
- Parent
- hwOspfv2ProcessEntry
- Table
- hwOspfv2ProcessTable
- Siblings
- 32
Syntax
millionSecond Integer32
Values & Constraints
Object Constraints
range: -1--1
range: 1-60000
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hwOspfv2ProcessIdIndex The process ID indicates the OSPF process number. The value ranges from 1 to 4294967295. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2011.5.25.155.3.1.1 |
| hwOspfv2LsaArriveHoldIntvl This object indicates the Holdtime interval of intelligent-timer for receiving
OSPF LSAs. After an intelligent timer is enabled, the interval for receiving
LSAs is as follows: T… | column | millionSecond Integer32 | .1.3.6.1.4.1.2011.5.25.155.3.1.10 |
| hwOspfv2LsaOrigIntvl To avoid wasting network source due to network changes, OSPF defines that the
interval for updating LSAs is 5 seconds.
In a stable network, if the speed of route convergence is re… | column | millionSecond Integer32 | .1.3.6.1.4.1.2011.5.25.155.3.1.11 |
| hwOspfv2LsaOrigMaxIntvl This object indicates the maximum interval of intelligent-timer for updating
OSPF LSAs. When hwOspfv2LsaOrigMaxIntvl is specified, you need also specify
hwOspfv2LsaOrigStartIntvl… | column | millionSecond Integer32 | .1.3.6.1.4.1.2011.5.25.155.3.1.12 |
| hwOspfv2LsaOrigStartIntvl This object indicates the initial interval of intelligent-timer for updating
OSPF LSAs. When hwOspfv2LsaOrigStartIntvl is specified, you need also specify
hwOspfv2LsaOrigMaxIntvl … | column | millionSecond Integer32 | .1.3.6.1.4.1.2011.5.25.155.3.1.13 |
| hwOspfv2LsaOrigHoldIntvl This object indicates the Holdtime interval of intelligent-timer for updating
OSPF LSAs. After an intelligent timer is enabled, the interval for updating
LSAs is as follows: The… | column | millionSecond Integer32 | .1.3.6.1.4.1.2011.5.25.155.3.1.14 |
| hwOspfv2LsaOrigIntvlOtherType This object indicates the interval for updating LSAs, excluding OSPF router
LSAs and network LSAs. hwOspfv2LsaOrigIntvlOtherType and hwOspfv2LsaOrigIntvl
cannot be specified tog… | column | second Integer32 | .1.3.6.1.4.1.2011.5.25.155.3.1.15 |
| hwOspfv2LsdbOverflowLimit The maximum number of external LSAs in OSPF LSDB.
When this node is set to 0, it means that no limits exist. | column | Integer32 | .1.3.6.1.4.1.2011.5.25.155.3.1.16 |
| hwOspfv2MaxLoadBalaNumber The maximum number of equal-cost routes to a destination in the routing table. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.25.155.3.1.17 |
| hwOspfv2AseRouteMaxNumber The maximum number of ASE routes that are supported by OSPF. | column | Integer32 | .1.3.6.1.4.1.2011.5.25.155.3.1.18 |
| hwOspfv2InterRouteMaxNumber The maximum number of inter-area routes that are supported by OSPF. | column | Integer32 | .1.3.6.1.4.1.2011.5.25.155.3.1.19 |
| hwOspfv2VpnName The name of VPN instance to which the process belongs.
The process instance needs to be specified when the process is created,
and then cannot be changed. | column | OctetString | .1.3.6.1.4.1.2011.5.25.155.3.1.2 |
| hwOspfv2IntraRouteMaxNumber The maximum number of intra-area routes that are supported by OSPF. | column | Integer32 | .1.3.6.1.4.1.2011.5.25.155.3.1.20 |
| hwOspfv2RetransLimitMaxNumber The maximum count of retransmission. The value is an integer that ranges from 2 to 255.
When the retransmission limit is disabled, the value is set to 0. | column | Integer32 | .1.3.6.1.4.1.2011.5.25.155.3.1.21 |
| hwOspfv2Rfc1583Compatibility It is used to enable the routing rule for compatible RFC 1583. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.5.25.155.3.1.22 |
| hwOspfv2ShamHello It is used to enable the sham-hello feature of OSPF.
After the feature is enabled, OSPF updates the timeout timer of the neighbor when
receiving protocol packets of various types. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.5.25.155.3.1.23 |
| hwOspfv2SpfSchIntvlUnit The value of the object identifies the interval unit for OSPF to calculate
routes. This object must be specified together with hwOspfv2SpfSchIntervalNumber.
By default, this ob… | column | Enumeration | .1.3.6.1.4.1.2011.5.25.155.3.1.24 |
| hwOspfv2SpfSchIntvlNumber The value of the object identifies the interval for OSPF to calculate routes.
This object must be specified together with hwOspfv2SpfSchIntervalUnit. By
default, this object is … | column | Integer32 | .1.3.6.1.4.1.2011.5.25.155.3.1.25 |
| hwOspfv2SpfSchMaxIntvl This object indicates the maximum interval of intelligent timer for OSPF to
perform the SPF calculation. When hwOspfv2SpfSchMaxIntvl is specified, you
need also specify hwOspfv2… | column | millionSecond Integer32 | .1.3.6.1.4.1.2011.5.25.155.3.1.26 |
| hwOspfv2SpfSchStartIntvl This object indicates the initial interval of intelligent timer for OSPF to
perform the SPF calculation. When hwOspfv2SpfSchStartIntvl is specified, you
need also specify hwOspf… | column | millionSecond Integer32 | .1.3.6.1.4.1.2011.5.25.155.3.1.27 |
| hwOspfv2OpaqueCapability It is used to enable opaque-LSAs capability. When the capability is enabled,
then the OSPF process can generate opaque LSAs and process the opaque LSAs
received from neighbors. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.5.25.155.3.1.29 |
| hwOspfv2ConfigRouterId A 32-bit integer uniquely identifies the router in the Autonomous System.
OSPF private router ID can be configured through this node. The default
value is 0.0.0.0. If the value o… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2011.5.25.155.3.1.3 |
| hwOspfv2TrafficAdjustment It is used to enable IGP-shortcut feature. The value false means disable.
Otherwise, the value true means enable. If you want to set this node to false,
please check whether Loc… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.5.25.155.3.1.30 |
| hwOspfv2TrafficAdvertise It is used to enable IGP-shortcut and Forwarding Adjacency feature. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.5.25.155.3.1.31 |
| hwOspfv2FlushTimer The value of the flush timer. When configuring or undoing OSPF process,
flush self-originated LSAs first.
If the timer expires, stop flushing LSAs, and then reset the process.
Th… | column | Integer32 | .1.3.6.1.4.1.2011.5.25.155.3.1.32 |
| hwOspfv2ProcessRowStatus This node is used to create and destroy rows.
Because CreateAndWait is not supported, you can set this node to CreatAndGo
to create a new process. If the process is created succes… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.2011.5.25.155.3.1.33 |
| hwOspfv2ActualRouterId This node is used to get actual router ID of process and it is a read-only node. If the node hwOspfv2ConfigRouterId is not set, the actual router ID should default to the value of… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2011.5.25.155.3.1.4 |
| hwOspfv2BandwidthReference The reference value that is used to calculate the link cost.
If there is no explicit link cost, OSPF calculates the cost according to the
bandwidth of the link (cost = reference v… | column | Mbit/s SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2011.5.25.155.3.1.5 |
| hwOspfv2Description The description of the OSPF process. | column | OctetString | .1.3.6.1.4.1.2011.5.25.155.3.1.6 |
| hwOspfv2LsaArriveIntvl To avoid wasting network resources due to network changes, OSPF defines that the
interval for receiving LSAs is 1 second.
In a stable network, if the fast speed of route convergen… | column | millionSecond Integer32 | .1.3.6.1.4.1.2011.5.25.155.3.1.7 |
| hwOspfv2LsaArriveMaxIntvl This object indicates the maximum interval of intelligent-timer for receiving
OSPF LSAs. When hwOspfv2LsaArriveMaxIntvl is specified, you need also specify
hwOspfv2LsaArriveStar… | column | millionSecond Integer32 | .1.3.6.1.4.1.2011.5.25.155.3.1.8 |
| hwOspfv2LsaArriveStartIntvl This object indicates the initial interval of intelligent-timer for receiving
OSPF LSAs. When hwOspfv2LsaArriveStartIntvl is specified, you need also specify
hwOspfv2LsaArriveMax… | column | millionSecond Integer32 | .1.3.6.1.4.1.2011.5.25.155.3.1.9 |