hwifEthernetVlanDefault
HUAWEI-ETHERLIKE-EXT-MIB ·
.1.3.6.1.4.1.2011.5.14.1.4.1.13
Object
column
r/w
Integer32
Describes the native VLAN of an Ethernet port.
When you need to set the packets of the upstream Ethernet
port with the VLAN tag, operate this leaf. After the native
VLAN of the Ethernet port is configured successfully,
If the VLAN ID of the Ethernet port is the same as that
of the native VLAN, the packets of the upstream Ethernet
port do not contain the VLAN tag, that is, the packets are untagged.
If the VLAN ID of the Ethernet port is not the same as that
of the native VLAN, the packets of the upstream Ethernet
port contain the VLAN tag.
Before specifying the native VLAN of a port, make sure that the port
has been added to the VLAN.
This does not work:
when you set the native VLAN on a sub-port of an aggregated port.
When you set the native on an aggregated master port,
the configuration of all physical ports within the aggregated group is changed.
Range: 1-4093
Default: 1
Context
- MIB
- HUAWEI-ETHERLIKE-EXT-MIB
- OID
.1.3.6.1.4.1.2011.5.14.1.4.1.13- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- hwEthernetEntry
- Table
- hwEthernetTable
- Siblings
- 45
Syntax
Integer32
Values & Constraints
Object Constraints
range: -1--1
range: 1-4093
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hwifEthernetDuplex Ethernet port duplex mode.
Options:
1. full(1) -indicates that at one moment, the port can be sending packets and receiving packets
2. half(2) -indicates that at one momen… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.1 |
| hwifEthernetPeerNegotiate Ethernet peer port auto-negotiation node (which is needed by MA5100 V2R1 product,
and can be selected by other products of the fixed network depending on the practice.) | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.5.14.1.4.1.10 |
| hwifEthernetPauseFrameTag Whether the Ethernet port supports Pause frame flow control.
Options:
1. on(1) -support Tx Pause and Rx Pause
2. off(2) -not support
3. rxpause(3) -support Rx Pause not… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.11 |
| hwifEthernetPauseFrameSending Ethernet pause frame sending tag (Notes: only for Huawei product of Ma5100)
Whether the network interface is sending Pause frame (which is needed by
MA5100 V2R1 product, and can … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.5.14.1.4.1.12 |
| hwifEthernetOnlineState Ethernet port online status (Notes: only for Huawei product of Ma5100).
Whether the network interface is online (which is needed by MA5100 V2R1
product, and can be selected by ot… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.5.14.1.4.1.14 |
| hwifEthernetLineSelfAdaptMode Connecting adaptatively tag,default false.
Options:
1. true(1) -adapting by itself
2. false(2) -adapting by manual
The self-adaptation switch:
In the case of true,… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.5.14.1.4.1.15 |
| hwifEthernetTrafficBroadcast Indicates the broadcast traffic suppression on an Ethernet port.
Range: -1,0-13
13: indicates full-suppression of traffic, and 0 indicates no traffic suppression.
-1: indicates … | column | Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.16 |
| hwifEthernetTrafficMulticast Indicates the unknown multicast traffic suppression on an Ethernet port.
Range: -1,0-13 … | column | Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.17 |
| hwifEthernetTrafficUnknowncast Indicates the unknown unicast traffic suppression on an Ethernet port.
Range: -1,0-13 … | column | Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.18 |
| hwifEthernetJumboEnable This object is used to enable or disable jumbo frames.
When the carriers' servers need to exchange a large amount of data with their devices,
operate this object to enable jumbo… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.19 |
| hwifEthernetMTU This object is used for setting the MTU of a ETH port
0 indicates to restore the default value.
-1 indicates the value is invalid.
Range: -1-0, 1519-9280 | column | Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.2 |
| hwifPortDefPriority Port default 802.1p priority (Notes: Default value is 0.)
------------------------------------------------------------
F/ S/ P Port Priority
---------------------------… | column | Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.20 |
| hwifEthernetComboWorkMode Work mode information of combo port.
Options:
1. electric(1) -combo port works in electric mode
2. optic(2) -combo port works in optic mode
3. autoFiber(5) -combo port wor… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.21 |
| hwifEthernetLineTest It used to test the line status.
Options:
1. test(1) -Test the line operation
2. notSupport(-1) -Indicates the board does not support this operation | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.22 |
| hwifEthernetAutoTxPowerOffSwitch Indicates the switch of Tx auto power off.
Options:
1. invalid(-1) -invalid value
2. enabled(1) -enable Tx auto poweroff
3. disabled(2) -disable Tx auto poweroff
Default… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.23 |
| hwifEthernetAutoTxPowerOffDetectTime Indicates the detecting LOS time of TX auto power off.
Set:
'1-60' means valid value to be set,
Get:
'-1' means invalid value,
Unit: minutes | column | minutes Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.24 |
| hwifEthernetTxPowerState Indicates the state of ethernet port Tx.
Options:
1. invalid(-1) -invalid value
2. on(1) -ethernet port Tx is on
3. off(2) -ethernet port Tx is off | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.25 |
| hwEthBind15minAlarmTableIndex Indicates the 15 minutes alarm profile index for the ethernet port.
Set:
'0' means to unbind 15 minutes alarm profile,
'1-16' means to bind 15 minutes alarm profile to the ether… | column | Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.26 |
| hwEthBind15minWarningTableIndex Indicates the 15 minutes warning profile index for the ethernet port.
Set:
'0' means to unbind 15 minutes warning profile,
'1-16' means to bind 15 minutes warning profile to the… | column | Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.27 |
| hwEthBind24hourAlarmTableIndex Indicates the 24 hours alarm profile index for the ethernet port.
Set:
'0' means to unbind 24 hours alarm profile,
'1-16' means to bind 24 hours alarm profile to the ethernet po… | column | Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.28 |
| hwEthBind24hourWarningTableIndex Indicates the 24 hours warning profile index for the ethernet port.
Set:
'0' means to unbind 24 hours warning profile,
'1-16' means to bind 24 hours warning profile to the ether… | column | Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.29 |
| hwifEthernetSpeed Ethernet port rate.
Options:
1. auto(0) -Ethernet port rate 0
2. s10M(10) -Ethernet port rate forced 10M
3. s100M(100) -Ethernet port rate forced… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.3 |
| hwifEthernetPortType Indicates the ethernet port type.
Options:
1. fe(1) -Ethernet port type FE
2. ge(2) -Ethernet port type GE
3. xge(3) -Ethernet port type 10GE… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.30 |
| hwifEthernetPortTypeAutoSensing Indicates the switch for the port type auto-sensing.
When the switch is enabled, the port will working on GE or FE mode according to that of link partner.
Options:
1. enable(1) … | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.31 |
| hwifEthernetLoopbackTest It used to start loopback test.
Options:
1. test(1) -Start loopback test. | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.32 |
| hwifEthernetOfflineReason Indicates the offline reason of ethernet port.
Options:
1. invalid(-1) -invalid value
2. unknown(1) -unknown
3. boardabnormal(2) … | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.33 |
| hwifEthernetTxPowerResumeDetect Indicates the switch of Tx auto power resume detection.
Options:
1. invalid(-1) -invalid value
2. manual(1) -Tx power resume detection manually
3. auto(2) -Tx power res… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.34 |
| hwifEthernetTxPowerDetectInterval Indicates the interval of Tx power pulse.
'100-300' means valid value,
'-1' means invalid value,
Unit: seconds | column | seconds Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.35 |
| hwifEthernetTxPowerResumeDuration Indicates the duration of Tx power pulse.
'100-3000' means valid value,
'-1' means invalid value,
Unit: milliseconds | column | milliseconds Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.36 |
| hwifEthernetTxPowerManualResume Indicates the operation of manual resumption.
Options:
1. invalid(-1) -invalid value
2. start(1) -start Tx power resumption | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.37 |
| hwifEthernetOpticModuleState Indicates the state of optical module.
Options:
1. normal(1)
2. absent(2)
3. abnormal(3)
4. mismatch(4)
'2147483647' means invalid value. | column | Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.38 |
| hwifEthernetLinkflapping This object is used for setting the link flapping time of a ETH port
0 indicates disable the ETH port link flapping.
10-5000 indicates enable ETH link flapping.
-1: indicates … | column | millisecond Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.39 |
| hwifEthernetLoopback Ethernet port loop back mode.
Options:
1. noloopback(1) -cancel loopback
2. internalloopback(2) -local loopback
3. externalloopback(3) -remote loopback
Ports only on the… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.4 |
| hwifEthernetOfflineTxOffTime Indicates the the offline time on an Ethernet port.
Range: -1,0-1000
0-1000: indicates the offline time when link down.
0 means the offline time function is off.
-1: indicates i… | column | millisecond Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.40 |
| hwifEthernetTrafficRateBroadcast Indicates the broadcast traffic suppression on an Ethernet port.
Range: -1,0-24414
Unit: pps.
24414: indicates full-suppression of traffic, and 0 indicates no traffic suppression… | column | Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.41 |
| hwifEthernetTrafficRateMulticast Indicates the unknown multicast traffic suppression on an Ethernet port.
Range: -1,0-24414
Unit: pps.
24414: indicates full-suppression of t… | column | Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.42 |
| hwifEthernetTrafficRateUnknowncast Indicates the unknown unicast traffic suppression on an Ethernet port.
Range: -1,0-24414
Unit: pps.
24414: indicates full-suppression o… | column | Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.43 |
| hwEthernetLightTestTimeduration This object is used to configure the time duration of light test, 0s ~ 3600s,
0s means stopping the testing immidiately. | column | Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.44 |
| hwEthernetLightTestTestStatus This object is used to configure the laser test status.
Options:
1. enable(1) - laser tx is enable
2. disable(2) - laser tx is disable
3. invalid(-1) … | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.45 |
| hwEthernetLightTestFinshStatus This object is used to configure the laser status after the test is completed.
Options:
1. enable(1) - laser tx is enable
2. disable(2) - laser tx is disable
3. origi… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.46 |
| hwifEthernetMdi Ethernet port cable type.
Options:
1. mdiII(1) -direct connection cable
2. mdiX(2) -cross-over cable
3. mdiAuto(3) -auto-sensing
4. invalid(-1) -invalid value
After the ne… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.5 |
| hwMaxMacLearn The max MAC learned by the Ethernet port.
The invalid value is 65535. | column | Integer32 | .1.3.6.1.4.1.2011.5.14.1.4.1.6 |
| hwifMacAddressLearn Status indicates if the interface is allowed to learn MAC address.
Options:
1. enabled(1) -Indicates the interface can learn MAC address.
2. disabled(2) -Indicates the interface… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.7 |
| hwifTag Ethernet interface tag.
Options:
1. tag(1) -This value is not supported.
2. untag(2) -This value is not supported.
3. multi(3) -This value is not supported. | column | Enumeration | .1.3.6.1.4.1.2011.5.14.1.4.1.8 |
| hwifEthernetNegotiate Ethernet port negotiation mode.
Options:
1. true(1) -auto-negotiation mode of an Ethernet port is enabled, Ethernet port automatically
negotiates the port rate and … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.5.14.1.4.1.9 |