hwMinMTunnelDownAlarm
HUAWEI-DC-TRAP-MIB ·
.1.3.6.1.4.1.2011.5.25.37.2.111
Object
notification
For Mac in Mac tunnel. Mac tunnel have two status: up or down, when physical interface is down or some cc package
can't arrive to the other side of mac in mac tunnel, the status of tunnel will be down
1 Notice/Trap name: Tunnel down
2 Notice/Trap generation cause: when All mac tunnel have been down in the mac tunnel group
3 Repair suggestions:
make one of the mac tunnel up in the mac tunnel group
Context
- MIB
- HUAWEI-DC-TRAP-MIB
- OID
.1.3.6.1.4.1.2011.5.25.37.2.111- Type
- notification
- Status
- current
- Parent
- hwDCTraps
- Siblings
- 126
Syntax
No syntax metadata recorded.
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hwMPUSynClkFaulty MPU sync clock signal faulty! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.1 |
| hwBrdAutoSwtFail Board automatically switch syn-clock but it locked failed! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.10 |
| hwWriteFlashError write flash error! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.100 |
| hwBoardReset board reset! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.101 |
| hwBoardResetSuccess board reset success! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.102 |
| hwSlaveMPUReset slave MPU reset ! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.103 |
| hwMasterSlaveSwap master slave swap! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.104 |
| hwRTCFail RTC failure! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.105 |
| hwExchangeChipFail 5695 exchange chip fail! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.106 |
| hwTempResume Board temprature over threshold resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.107 |
| hwOpticalModuleInsert optical module plug in ! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.108 |
| hwOpticalModuleRemove optical module plug out ! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.109 |
| hwBrdAutoSwt Board automatically switch syn-clock! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.11 |
| hwFPGAAbnormal FPGA abnormal ! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.110 |
| hwMinMTunnelUpAlarm For Mac in Mac tunnel. Mac tunnel have two status: up or down, if cc package can arrive to the other side of mac
in mac tunnel, the status of tunnel will be up
1 Notice/Trap name:… | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.112 |
| hwInterfacePhysicalDown This trap is to indicate port link down on physical layer. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.113 |
| hwInterfacePhysicalUp This trap is to indicate port link up on physical layer. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.114 |
| hwBTBStartupFileNameDifferent In the BTB system ,the start-up file name of master and slave chassis is different .
Used for BTB or its extend system. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.119 |
| hwBrdClkLockERR Board fabric clock is unlocked! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.12 |
| hwBTBChassisRunningModeConflict The Master and Slave chassises running modes conflict.Used for BTB or its extend system. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.120 |
| hwBTBCtrlChannelFail The FE control channel failture, as physical link from up to down or channel blocked.
Used for BTB or its extend system. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.121 |
| hwBTBCtrlChannelFailResume The FE control channel failture resume.Used for BTB or its extend system. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.122 |
| hwBTBDataChannelFail The data channel failture, all optical links down between chassises.Used for BTB or its extend system. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.123 |
| hwBTBDataChannelFailResume The data channel failture resume.Used for BTB or its extend system. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.124 |
| hwBTBClkChannelFail The clock channel failture, clock link down between chassises.Used for BTB or its extend system. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.125 |
| hwBTBClkChannelFailResume The clock Channel failture resume.Used for BTB or its extend system. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.126 |
| hwBTBSFUOpticInterfaceError The optical fiber connection error, the connection of SFU fiber between chassises is not correct.
Used for BTB or its extend system. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.127 |
| hwBTBSFUOpticInterfaceErrorResume The optical fiber connection error resume.Used for BTB or its extend system. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.128 |
| hwBTBVSRInterfaceInvalid The SFU VSR(very short reach) interface invalid.Used for BTB or its extend system. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.129 |
| hwBrdClkLockERRResume Board fabric clock unlock to current clock resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.13 |
| hwBTBVSRInterfaceInvalidResume The SFU VSR(very short reach) interface invalid resume.Used for BTB or its extend system. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.130 |
| hwBTBSlaveChassisNoHeart The slave chassis no heart.Used for BTB or its extend system. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.131 |
| hwBTBNoSlaveChassis No slave chassis connected to the master chassis in the BTB system.Used for BTB or its extend system. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.132 |
| hwBTBSlaveChassisRegisted The slave chassis registe successful.Used for BTB or its extend system. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.133 |
| hwBTBSlaveChassisRegisteFail The slave chassis registe failed.Used for BTB or its extend system. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.134 |
| hwBTBChassisTypeConflict The chassis information conflict in the PAF and Nvram.Used for BTB or its extend system. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.135 |
| hwSuperChangeSuccesful Super change successful. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.136 |
| hwSuperChangeFailure Super change Failure. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.137 |
| hwOpticaPowerAbnormal Optical Transceiver power abnormal. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.138 |
| hwEpldAbnormal Epld logic abnormal. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.139 |
| hwBrdRemoved Board pulled out! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.14 |
| hwPhyChipAbnormal PHY chip is abnormal. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.140 |
| hwSerdesAbnormal Serdes interface of PHY chip abnormal. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.141 |
| hwBoardAbnormal Board is abnormal. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.142 |
| hwFeChannelAbnormal FE data channel is abnormal | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.143 |
| hwParityCheckAbnormal Data parity check is abnormal | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.144 |
| hwPhyClockAbnormal The clock of PHY chip is abnormal. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.145 |
| hwPortAutoNegotiateFail The ethernet port negotiate failed | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.146 |
| hwPortSemiduplex The ethernet port work at semi duplex state. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.147 |
| hwScuStartModeSetFail The start mode of SCU set failed | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.148 |
| hwMemoryExhaust MPU memory exhaust. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.149 |
| hwBrdInserted Board plugged in! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.15 |
| hwMemoryExhaustClear MPU memory usage resume to normal. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.150 |
| hwMethAbnormal The Meth interface is abnormal. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.151 |
| hwLpuNotTight The LPU board is not tightly installed. Install the board again. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.152 |
| hwLicenseFail License fail. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.153 |
| hwHaBatchBegin No command line can be entered because batch backup is processing. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.154 |
| hwHaBatchEnd Command lines can be entered because batch backup ends. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.155 |
| hwHaSmoothBegin No command line can be entered because data smooth is processing. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.156 |
| hwHaSmoothEnd Command lines can be entered because data smooth ends. | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.157 |
| hwFanUp Fan register! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.158 |
| hwBrdUp Board register! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.16 |
| hwClkSrcMiss CLK source Loss Of Signal! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.17 |
| hwClkAllSrcLost CLK all source lost! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.18 |
| hwClkAllSrcLostResume CLK all source lost resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.19 |
| hwMPUSynClkFaultyResume MPU sync clock signal faulty resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.2 |
| hwClkFail CLK hardware failed! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.20 |
| hwClkFailResume CLK hardware failed resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.21 |
| hwClkNoHeartbeat CLK No Heartbeat! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.22 |
| hwClkNoHeartbeatResume CLK No Heartbeat resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.23 |
| hwLPULostSynAlarm LPU SERDES interface is lost synchronization! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.24 |
| hwLPUOpenChannelError LPU SERDES interface open error! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.25 |
| hwLPUSlfTstErr LPU self test error! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.26 |
| hwLPU3ClkSwitch LPU 3 class clock is switch! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.27 |
| hwSFULostHrtReset SFU is reset because of heart beat loss! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.28 |
| hwSFULinkLostReset SFU is reset because of SERDES interface input channel link lost numbers over threshold! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.29 |
| hwSlaveMPUNoResp Slave MPU has no response! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.3 |
| hwSFUChannelLinkLost SFU check SERDES interface input channel link lost! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.30 |
| hwSFUInChannelOpenFail SFU SERDES interface input channel is opened failed! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.31 |
| hwVoltSensorFail Board voltage monitor failure! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.32 |
| hwVoltSensorFailResume Board voltage monitor failure resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.33 |
| hwVoltBtmC Board voltage below fatal threshold! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.34 |
| hwVoltBtmCResume Board voltage below fatal threshold resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.35 |
| hwVoltSprC Board voltage over fatal threshold! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.36 |
| hwVoltSprCResume Board voltage over fatal threshold resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.37 |
| hwVoltBtmM Board voltage below major threshold! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.38 |
| hwVoltBtmMResume Board voltage below major threshold resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.39 |
| hwSlaveMPUNoRespResume Slave MPU has no response resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.4 |
| hwVoltSprM Board voltage over major threshold! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.40 |
| hwVoltSprMResume Board voltage over major threshold resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.41 |
| hwTempSensorFail Board temprature monitor failure! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.42 |
| hwTempSensorFailResume Board temperature monitor failure resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.43 |
| hwTempMnr Board temperature over minor threshold! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.44 |
| hwTempMnrResume Board temperature over minor threshold resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.45 |
| hwTempMjr Board temperature over major threshold! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.46 |
| hwTempMjrResume Board temperature over major threshold resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.47 |
| hwTempCtl Board temperature over fatal threshold! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.48 |
| hwTempCtlResume Board temperature over fatal threshold resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.49 |
| hwBrdChannelFaulty Board channel faulty! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.5 |
| hwFanHFail Fan hardware failure! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.50 |
| hwDCFanFail Fan failure! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.51 |
| hwDCFanFailResume Fan failure resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.52 |
| hwFanAbsent Fan absent! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.53 |
| hwFanAbsentResume Fan absent resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.54 |
| hwFanCabUN Fan cable unplugged! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.55 |
| hwFanCabUNResume Fan cable unplugged resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.56 |
| hwPwrFail Power failure! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.57 |
| hwPwrFailResume Power failure resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.58 |
| hwPwrAbsent Power absent! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.59 |
| hwBrdChannelFaultyResume Board channel faulty resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.6 |
| hwPwrAbsentResume Power absent resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.60 |
| hwPwrCabUN Power monitor cable unplugged! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.61 |
| hwPwrCabUNResume Power monitor cable unplugged resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.62 |
| hwLCDHFail LCD hardware failure! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.63 |
| hwLCDFail LCD failure! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.64 |
| hwLCDAbsent LCD absent! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.65 |
| hwLCDAbsentResume LCD absent resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.66 |
| hwLCDCabUN LCD cable unplugged! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.67 |
| hwLCDCabUNResume LCD cable unplugged resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.68 |
| hwROMFail EEPROM failure! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.69 |
| hwBrdNofullin Board not full in! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.7 |
| hwMonitorBUSFail MonitorBUS failure! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.70 |
| hwMonitorBUSFailResume MonitorBUS failure resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.71 |
| hwBoardOfflineChange Board power status change! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.72 |
| hwBrdNofullinResume Board not full in resume! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.8 |
| hwBrdTypeNoMatchReset Board is reset because of the chip type is not matching! | notification | - | .1.3.6.1.4.1.2011.5.25.37.2.9 |