HUAWEI-DC-TRAP-MIB
The HUAWEI-DC-TRAP-MIB provides information about DataComm TRAPS.
hwDCTrapMIB
1.3.6.1.4.1.2011.5.25.37
Imported Objects
| ENTITY-MIB | entPhysicalName |
| HUAWEI-MIB | hwDatacomm |
| RFC1213-MIB | ifDescr ifIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | DisplayString |
Objects (9)
hwDCTrapMIB
|
.1.3.6.1.4.1.2011.5.25.37 |
|
|
hwDCTrapControl
|
.1.3.6.1.4.1.2011.5.25.37.1 |
|
hwDCCtrlTrap
r/w
|
OctetString | .1.3.6.1.4.1.2011.5.25.37.1.1 |
|
hwTunnelGroupID
|
Integer32 | .1.3.6.1.4.1.2011.5.25.37.1.2 |
|
hwDCTrapReason
|
SNMPv2-TCDisplayString | .1.3.6.1.4.1.2011.5.25.37.1.3 |
|
hwDCTraps
|
.1.3.6.1.4.1.2011.5.25.37.2 |
|
|
hwDCTrapConformance
|
.1.3.6.1.4.1.2011.5.25.37.3 |
|
|
hwDCTrapGroups
|
.1.3.6.1.4.1.2011.5.25.37.3.1 |
|
|
hwDCTrapCompliances
|
.1.3.6.1.4.1.2011.5.25.37.3.2 |
Notifications / Traps (127)
| Name | OID | Description |
|---|---|---|
hwMPUSynClkFaulty
|
.1.3.6.1.4.1.2011.5.25.37.2.1 |
MPU sync clock signal faulty! |
|
hwBrdAutoSwtFail
|
.1.3.6.1.4.1.2011.5.25.37.2.10 |
Board automatically switch syn-clock but it locked failed! |
|
hwWriteFlashError
|
.1.3.6.1.4.1.2011.5.25.37.2.100 |
write flash error! |
|
hwBoardReset
|
.1.3.6.1.4.1.2011.5.25.37.2.101 |
board reset! |
|
hwBoardResetSuccess
|
.1.3.6.1.4.1.2011.5.25.37.2.102 |
board reset success! |
|
hwSlaveMPUReset
|
.1.3.6.1.4.1.2011.5.25.37.2.103 |
slave MPU reset ! |
|
hwMasterSlaveSwap
|
.1.3.6.1.4.1.2011.5.25.37.2.104 |
master slave swap! |
|
hwRTCFail
|
.1.3.6.1.4.1.2011.5.25.37.2.105 |
RTC failure! |
|
hwExchangeChipFail
|
.1.3.6.1.4.1.2011.5.25.37.2.106 |
5695 exchange chip fail! |
|
hwTempResume
|
.1.3.6.1.4.1.2011.5.25.37.2.107 |
Board temprature over threshold resume! |
|
hwOpticalModuleInsert
|
.1.3.6.1.4.1.2011.5.25.37.2.108 |
optical module plug in ! |
|
hwOpticalModuleRemove
|
.1.3.6.1.4.1.2011.5.25.37.2.109 |
optical module plug out ! |
|
hwBrdAutoSwt
|
.1.3.6.1.4.1.2011.5.25.37.2.11 |
Board automatically switch syn-clock! |
|
hwFPGAAbnormal
|
.1.3.6.1.4.1.2011.5.25.37.2.110 |
FPGA abnormal ! |
|
hwMinMTunnelDownAlarm
|
.1.3.6.1.4.1.2011.5.25.37.2.111 |
For Mac in Mac tunnel. Mac tunnel have two status: up or down, when physical interface is down or some cc package
can't arrive to the other side of mac in mac tunnel, the status of tunnel will be down
1 Notice/Trap name: Tunnel down
2 Notice/Trap generation cause: when All mac tunnel have been down in the mac tunnel group
3 Repair suggestions:
make one of the mac tunnel up in the mac tunnel group
|
|
hwMinMTunnelUpAlarm
|
.1.3.6.1.4.1.2011.5.25.37.2.112 |
For Mac in Mac tunnel. Mac tunnel have two status: up or down, if cc package can arrive to the other side of mac in mac tunnel, the status of tunnel will be up 1 Notice/Trap name: Tunnel up 2 Notice/Trap generation cause: one of the tunnel is up in the mac tunnel group 3 Repair suggestion: |
|
hwInterfacePhysicalDown
|
.1.3.6.1.4.1.2011.5.25.37.2.113 |
This trap is to indicate port link down on physical layer. |
|
hwInterfacePhysicalUp
|
.1.3.6.1.4.1.2011.5.25.37.2.114 |
This trap is to indicate port link up on physical layer. |
|
hwBTBStartupFileNameDifferent
|
.1.3.6.1.4.1.2011.5.25.37.2.119 |
In the BTB system ,the start-up file name of master and slave chassis is different . Used for BTB or its extend system. |
|
hwBrdClkLockERR
|
.1.3.6.1.4.1.2011.5.25.37.2.12 |
Board fabric clock is unlocked! |
|
hwBTBChassisRunningModeConflict
|
.1.3.6.1.4.1.2011.5.25.37.2.120 |
The Master and Slave chassises running modes conflict.Used for BTB or its extend system. |
|
hwBTBCtrlChannelFail
|
.1.3.6.1.4.1.2011.5.25.37.2.121 |
The FE control channel failture, as physical link from up to down or channel blocked. Used for BTB or its extend system. |
|
hwBTBCtrlChannelFailResume
|
.1.3.6.1.4.1.2011.5.25.37.2.122 |
The FE control channel failture resume.Used for BTB or its extend system. |
|
hwBTBDataChannelFail
|
.1.3.6.1.4.1.2011.5.25.37.2.123 |
The data channel failture, all optical links down between chassises.Used for BTB or its extend system. |
|
hwBTBDataChannelFailResume
|
.1.3.6.1.4.1.2011.5.25.37.2.124 |
The data channel failture resume.Used for BTB or its extend system. |
|
hwBTBClkChannelFail
|
.1.3.6.1.4.1.2011.5.25.37.2.125 |
The clock channel failture, clock link down between chassises.Used for BTB or its extend system. |
|
hwBTBClkChannelFailResume
|
.1.3.6.1.4.1.2011.5.25.37.2.126 |
The clock Channel failture resume.Used for BTB or its extend system. |
|
hwBTBSFUOpticInterfaceError
|
.1.3.6.1.4.1.2011.5.25.37.2.127 |
The optical fiber connection error, the connection of SFU fiber between chassises is not correct. Used for BTB or its extend system. |
|
hwBTBSFUOpticInterfaceErrorResume
|
.1.3.6.1.4.1.2011.5.25.37.2.128 |
The optical fiber connection error resume.Used for BTB or its extend system. |
|
hwBTBVSRInterfaceInvalid
|
.1.3.6.1.4.1.2011.5.25.37.2.129 |
The SFU VSR(very short reach) interface invalid.Used for BTB or its extend system. |
|
hwBrdClkLockERRResume
|
.1.3.6.1.4.1.2011.5.25.37.2.13 |
Board fabric clock unlock to current clock resume! |
|
hwBTBVSRInterfaceInvalidResume
|
.1.3.6.1.4.1.2011.5.25.37.2.130 |
The SFU VSR(very short reach) interface invalid resume.Used for BTB or its extend system. |
|
hwBTBSlaveChassisNoHeart
|
.1.3.6.1.4.1.2011.5.25.37.2.131 |
The slave chassis no heart.Used for BTB or its extend system. |
|
hwBTBNoSlaveChassis
|
.1.3.6.1.4.1.2011.5.25.37.2.132 |
No slave chassis connected to the master chassis in the BTB system.Used for BTB or its extend system. |
|
hwBTBSlaveChassisRegisted
|
.1.3.6.1.4.1.2011.5.25.37.2.133 |
The slave chassis registe successful.Used for BTB or its extend system. |
|
hwBTBSlaveChassisRegisteFail
|
.1.3.6.1.4.1.2011.5.25.37.2.134 |
The slave chassis registe failed.Used for BTB or its extend system. |
|
hwBTBChassisTypeConflict
|
.1.3.6.1.4.1.2011.5.25.37.2.135 |
The chassis information conflict in the PAF and Nvram.Used for BTB or its extend system. |
|
hwSuperChangeSuccesful
|
.1.3.6.1.4.1.2011.5.25.37.2.136 |
Super change successful. |
|
hwSuperChangeFailure
|
.1.3.6.1.4.1.2011.5.25.37.2.137 |
Super change Failure. |
|
hwOpticaPowerAbnormal
|
.1.3.6.1.4.1.2011.5.25.37.2.138 |
Optical Transceiver power abnormal. |
|
hwEpldAbnormal
|
.1.3.6.1.4.1.2011.5.25.37.2.139 |
Epld logic abnormal. |
|
hwBrdRemoved
|
.1.3.6.1.4.1.2011.5.25.37.2.14 |
Board pulled out! |
|
hwPhyChipAbnormal
|
.1.3.6.1.4.1.2011.5.25.37.2.140 |
PHY chip is abnormal. |
|
hwSerdesAbnormal
|
.1.3.6.1.4.1.2011.5.25.37.2.141 |
Serdes interface of PHY chip abnormal. |
|
hwBoardAbnormal
|
.1.3.6.1.4.1.2011.5.25.37.2.142 |
Board is abnormal. |
|
hwFeChannelAbnormal
|
.1.3.6.1.4.1.2011.5.25.37.2.143 |
FE data channel is abnormal |
|
hwParityCheckAbnormal
|
.1.3.6.1.4.1.2011.5.25.37.2.144 |
Data parity check is abnormal |
|
hwPhyClockAbnormal
|
.1.3.6.1.4.1.2011.5.25.37.2.145 |
The clock of PHY chip is abnormal. |
|
hwPortAutoNegotiateFail
|
.1.3.6.1.4.1.2011.5.25.37.2.146 |
The ethernet port negotiate failed |
|
hwPortSemiduplex
|
.1.3.6.1.4.1.2011.5.25.37.2.147 |
The ethernet port work at semi duplex state. |
|
hwScuStartModeSetFail
|
.1.3.6.1.4.1.2011.5.25.37.2.148 |
The start mode of SCU set failed |
|
hwMemoryExhaust
|
.1.3.6.1.4.1.2011.5.25.37.2.149 |
MPU memory exhaust. |
|
hwBrdInserted
|
.1.3.6.1.4.1.2011.5.25.37.2.15 |
Board plugged in! |
|
hwMemoryExhaustClear
|
.1.3.6.1.4.1.2011.5.25.37.2.150 |
MPU memory usage resume to normal. |
|
hwMethAbnormal
|
.1.3.6.1.4.1.2011.5.25.37.2.151 |
The Meth interface is abnormal. |
|
hwLpuNotTight
|
.1.3.6.1.4.1.2011.5.25.37.2.152 |
The LPU board is not tightly installed. Install the board again. |
|
hwLicenseFail
|
.1.3.6.1.4.1.2011.5.25.37.2.153 |
License fail. |
|
hwHaBatchBegin
|
.1.3.6.1.4.1.2011.5.25.37.2.154 |
No command line can be entered because batch backup is processing. |
|
hwHaBatchEnd
|
.1.3.6.1.4.1.2011.5.25.37.2.155 |
Command lines can be entered because batch backup ends. |
|
hwHaSmoothBegin
|
.1.3.6.1.4.1.2011.5.25.37.2.156 |
No command line can be entered because data smooth is processing. |
|
hwHaSmoothEnd
|
.1.3.6.1.4.1.2011.5.25.37.2.157 |
Command lines can be entered because data smooth ends. |
|
hwFanUp
|
.1.3.6.1.4.1.2011.5.25.37.2.158 |
Fan register! |
|
hwBrdUp
|
.1.3.6.1.4.1.2011.5.25.37.2.16 |
Board register! |
|
hwClkSrcMiss
|
.1.3.6.1.4.1.2011.5.25.37.2.17 |
CLK source Loss Of Signal! |
|
hwClkAllSrcLost
|
.1.3.6.1.4.1.2011.5.25.37.2.18 |
CLK all source lost! |
|
hwClkAllSrcLostResume
|
.1.3.6.1.4.1.2011.5.25.37.2.19 |
CLK all source lost resume! |
|
hwMPUSynClkFaultyResume
|
.1.3.6.1.4.1.2011.5.25.37.2.2 |
MPU sync clock signal faulty resume! |
|
hwClkFail
|
.1.3.6.1.4.1.2011.5.25.37.2.20 |
CLK hardware failed! |
|
hwClkFailResume
|
.1.3.6.1.4.1.2011.5.25.37.2.21 |
CLK hardware failed resume! |
|
hwClkNoHeartbeat
|
.1.3.6.1.4.1.2011.5.25.37.2.22 |
CLK No Heartbeat! |
|
hwClkNoHeartbeatResume
|
.1.3.6.1.4.1.2011.5.25.37.2.23 |
CLK No Heartbeat resume! |
|
hwLPULostSynAlarm
|
.1.3.6.1.4.1.2011.5.25.37.2.24 |
LPU SERDES interface is lost synchronization! |
|
hwLPUOpenChannelError
|
.1.3.6.1.4.1.2011.5.25.37.2.25 |
LPU SERDES interface open error! |
|
hwLPUSlfTstErr
|
.1.3.6.1.4.1.2011.5.25.37.2.26 |
LPU self test error! |
|
hwLPU3ClkSwitch
|
.1.3.6.1.4.1.2011.5.25.37.2.27 |
LPU 3 class clock is switch! |
|
hwSFULostHrtReset
|
.1.3.6.1.4.1.2011.5.25.37.2.28 |
SFU is reset because of heart beat loss! |
|
hwSFULinkLostReset
|
.1.3.6.1.4.1.2011.5.25.37.2.29 |
SFU is reset because of SERDES interface input channel link lost numbers over threshold! |
|
hwSlaveMPUNoResp
|
.1.3.6.1.4.1.2011.5.25.37.2.3 |
Slave MPU has no response! |
|
hwSFUChannelLinkLost
|
.1.3.6.1.4.1.2011.5.25.37.2.30 |
SFU check SERDES interface input channel link lost! |
|
hwSFUInChannelOpenFail
|
.1.3.6.1.4.1.2011.5.25.37.2.31 |
SFU SERDES interface input channel is opened failed! |
|
hwVoltSensorFail
|
.1.3.6.1.4.1.2011.5.25.37.2.32 |
Board voltage monitor failure! |
|
hwVoltSensorFailResume
|
.1.3.6.1.4.1.2011.5.25.37.2.33 |
Board voltage monitor failure resume! |
|
hwVoltBtmC
|
.1.3.6.1.4.1.2011.5.25.37.2.34 |
Board voltage below fatal threshold! |
|
hwVoltBtmCResume
|
.1.3.6.1.4.1.2011.5.25.37.2.35 |
Board voltage below fatal threshold resume! |
|
hwVoltSprC
|
.1.3.6.1.4.1.2011.5.25.37.2.36 |
Board voltage over fatal threshold! |
|
hwVoltSprCResume
|
.1.3.6.1.4.1.2011.5.25.37.2.37 |
Board voltage over fatal threshold resume! |
|
hwVoltBtmM
|
.1.3.6.1.4.1.2011.5.25.37.2.38 |
Board voltage below major threshold! |
|
hwVoltBtmMResume
|
.1.3.6.1.4.1.2011.5.25.37.2.39 |
Board voltage below major threshold resume! |
|
hwSlaveMPUNoRespResume
|
.1.3.6.1.4.1.2011.5.25.37.2.4 |
Slave MPU has no response resume! |
|
hwVoltSprM
|
.1.3.6.1.4.1.2011.5.25.37.2.40 |
Board voltage over major threshold! |
|
hwVoltSprMResume
|
.1.3.6.1.4.1.2011.5.25.37.2.41 |
Board voltage over major threshold resume! |
|
hwTempSensorFail
|
.1.3.6.1.4.1.2011.5.25.37.2.42 |
Board temprature monitor failure! |
|
hwTempSensorFailResume
|
.1.3.6.1.4.1.2011.5.25.37.2.43 |
Board temperature monitor failure resume! |
|
hwTempMnr
|
.1.3.6.1.4.1.2011.5.25.37.2.44 |
Board temperature over minor threshold! |
|
hwTempMnrResume
|
.1.3.6.1.4.1.2011.5.25.37.2.45 |
Board temperature over minor threshold resume! |
|
hwTempMjr
|
.1.3.6.1.4.1.2011.5.25.37.2.46 |
Board temperature over major threshold! |
|
hwTempMjrResume
|
.1.3.6.1.4.1.2011.5.25.37.2.47 |
Board temperature over major threshold resume! |
|
hwTempCtl
|
.1.3.6.1.4.1.2011.5.25.37.2.48 |
Board temperature over fatal threshold! |
|
hwTempCtlResume
|
.1.3.6.1.4.1.2011.5.25.37.2.49 |
Board temperature over fatal threshold resume! |
|
hwBrdChannelFaulty
|
.1.3.6.1.4.1.2011.5.25.37.2.5 |
Board channel faulty! |
|
hwFanHFail
|
.1.3.6.1.4.1.2011.5.25.37.2.50 |
Fan hardware failure! |
|
hwDCFanFail
|
.1.3.6.1.4.1.2011.5.25.37.2.51 |
Fan failure! |
|
hwDCFanFailResume
|
.1.3.6.1.4.1.2011.5.25.37.2.52 |
Fan failure resume! |
|
hwFanAbsent
|
.1.3.6.1.4.1.2011.5.25.37.2.53 |
Fan absent! |
|
hwFanAbsentResume
|
.1.3.6.1.4.1.2011.5.25.37.2.54 |
Fan absent resume! |
|
hwFanCabUN
|
.1.3.6.1.4.1.2011.5.25.37.2.55 |
Fan cable unplugged! |
|
hwFanCabUNResume
|
.1.3.6.1.4.1.2011.5.25.37.2.56 |
Fan cable unplugged resume! |
|
hwPwrFail
|
.1.3.6.1.4.1.2011.5.25.37.2.57 |
Power failure! |
|
hwPwrFailResume
|
.1.3.6.1.4.1.2011.5.25.37.2.58 |
Power failure resume! |
|
hwPwrAbsent
|
.1.3.6.1.4.1.2011.5.25.37.2.59 |
Power absent! |
|
hwBrdChannelFaultyResume
|
.1.3.6.1.4.1.2011.5.25.37.2.6 |
Board channel faulty resume! |
|
hwPwrAbsentResume
|
.1.3.6.1.4.1.2011.5.25.37.2.60 |
Power absent resume! |
|
hwPwrCabUN
|
.1.3.6.1.4.1.2011.5.25.37.2.61 |
Power monitor cable unplugged! |
|
hwPwrCabUNResume
|
.1.3.6.1.4.1.2011.5.25.37.2.62 |
Power monitor cable unplugged resume! |
|
hwLCDHFail
|
.1.3.6.1.4.1.2011.5.25.37.2.63 |
LCD hardware failure! |
|
hwLCDFail
|
.1.3.6.1.4.1.2011.5.25.37.2.64 |
LCD failure! |
|
hwLCDAbsent
|
.1.3.6.1.4.1.2011.5.25.37.2.65 |
LCD absent! |
|
hwLCDAbsentResume
|
.1.3.6.1.4.1.2011.5.25.37.2.66 |
LCD absent resume! |
|
hwLCDCabUN
|
.1.3.6.1.4.1.2011.5.25.37.2.67 |
LCD cable unplugged! |
|
hwLCDCabUNResume
|
.1.3.6.1.4.1.2011.5.25.37.2.68 |
LCD cable unplugged resume! |
|
hwROMFail
|
.1.3.6.1.4.1.2011.5.25.37.2.69 |
EEPROM failure! |
|
hwBrdNofullin
|
.1.3.6.1.4.1.2011.5.25.37.2.7 |
Board not full in! |
|
hwMonitorBUSFail
|
.1.3.6.1.4.1.2011.5.25.37.2.70 |
MonitorBUS failure! |
|
hwMonitorBUSFailResume
|
.1.3.6.1.4.1.2011.5.25.37.2.71 |
MonitorBUS failure resume! |
|
hwBoardOfflineChange
|
.1.3.6.1.4.1.2011.5.25.37.2.72 |
Board power status change! |
|
hwBrdNofullinResume
|
.1.3.6.1.4.1.2011.5.25.37.2.8 |
Board not full in resume! |
|
hwBrdTypeNoMatchReset
|
.1.3.6.1.4.1.2011.5.25.37.2.9 |
Board is reset because of the chip type is not matching! |