hwadsl2TSSiPsdMaskDsCfg
HUAWEI-ADSL-EXT-MIB ·
.1.3.6.1.4.1.2011.6.31.1.13.1.19
Object
The downstream PSD mask applicable at the U-C2 reference
point.
This parameter is used only for G992.3 or G992.5 and it may
impose PSD restrictions (breakpoints) in addition to the
Limit PSD mask defined in G992.5.
This is a string of 32 pairs of values in the following
structure:
Octets 0-1 - Index of 1st sub-carrier used in the context
of a first breakpoint.
Octet 2 - The PSD reduction for the sub-carrier indicated in
octets 0 and 1.
Octets 3-5 - Same, for a 2nd breakpoint.
Octets 6-8 - Same, for a 3rd breakpoint.
This architecture continues until octets 94-95, which are
associated with a 32nd breakpoint.
Each subcarrier index is an unsigned number in the range 1 and
NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to
255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are
in the range 0 to 190 (0 to -95dBm/Hz).
When the number of breakpoints is less than 32, all remaining
octets are set to the value 0. Note that the content of this
object should be correlated with the sub-carriers mask and with
the RFI setup.
Context
- MIB
- HUAWEI-ADSL-EXT-MIB
- OID
.1.3.6.1.4.1.2011.6.31.1.13.1.19- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- hwadslLineExtConfProfileCfgEntry
- Table
- hwadslLineExtConfProfileCfgTable
- Siblings
- 75
Syntax
ADSL2-LINE-TC-MIBAdsl2PsdMaskDs
- Source
- ADSL2-LINE-TC-MIBAdsl2PsdMaskDs
- Base type
OctetString
Values & Constraints
Type Constraints
range: 0..96
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hwadslLineExtConfProfileNameCfg This object is used by the hwadslLineExtConfProfileTable
in order to identify a row of this table.
Indicates the name of the extended line profile. | column | OctetString | .1.3.6.1.4.1.2011.6.31.1.13.1.1 |
| hwadslLineDisableToneSection3FlagCfg The enable flag of the third section.
Options:
1. enabled(1) - The third tone section is enabled
2. disabled(2) - The third tone section is disabled | column | Enumeration | .1.3.6.1.4.1.2011.6.31.1.13.1.10 |
| hwadslLineDisableToneSection4BeginCfg The begin index of the fourth section.
Range: 0-511 | column | Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.11 |
| hwadslLineDisableToneSection4EndCfg The end index of the fourth section.
Range: 0-511 | column | Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.12 |
| hwadslLineDisableToneSection4FlagCfg The enable flag of the fourth section.
Options:
1. enabled(1) - The fourth tone section is enabled
2. disabled(2) - The fourth tone section is disabled | column | Enumeration | .1.3.6.1.4.1.2011.6.31.1.13.1.13 |
| hwadsl2ChConfProfMinProtectionDsCfg If retransmission is not used in downstream direction,this parameter
is minimum impulse noise protection on downstream direction. The
minimum impulse noise protection for the bea… | column | HUAWEI-ADSL-MIBHWADSLSYMBOLPROTECTION | .1.3.6.1.4.1.2011.6.31.1.13.1.14 |
| hwadsl2ChConfProfMinProtectionUsCfg If retransmission is not used in upstream direction,this parameter
is minimum impulse noise protection on upstream direction. The
minimum impulse noise protection for the bearer … | column | HUAWEI-ADSL-MIBHWADSLSYMBOLPROTECTION | .1.3.6.1.4.1.2011.6.31.1.13.1.15 |
| hwAdslExtDsMinTrainSnrMgnCfg Maximum Trainning Margin in downstream.
Range: 0-310
Default: 30
Unit: tenth dB | column | tenth dB Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.16 |
| hwAdslExtUsMinTrainSnrMgnCfg Maximum Trainning Margin in upstream.
Range: 0-310
Default: 30
Unit: tenth dB | column | tenth dB Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.17 |
| hwAdslExtDsMaxPsdCfg Maximum PSD margin in downstream. | column | dBm/Hz Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.18 |
| hwadslLineDisableToneSection1BeginCfg The begin index of the first section.
Range: 0-511 | column | Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.2 |
| hwadsl2TranMissionStardardMaskCfg The transmission stardard mask .
The Mask bit and the corresponding Transmission Standard:
0x 1 1 1 1 1 1
ETSI T1.413 G992.5 G992.3 G992.2 G992… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.20 |
| hwadsl2TransMissionAnnexMaskCfg The transMission annex Mask.
The Mask bit and the corresponding Transmission Annex:
0x 1 1 1 1 1
Annex .J Annex .M Annex .L Annex .B Anne… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.21 |
| hwadsl2TransMissionAnnexMScopeCfg Annex M expand scope:
1-Tone Index(7~32)
2-Tone Index(7~36)
3-Tone Index(7~40)
4-Tone Index(7~44)
5-Tone Index(7~48)
6-Tone Index(7~52)
7-Tone Index(7~56)
8-Tone Index(7~60)
9-Ton… | column | HUAWEI-ADSL-MIBHWADSL2ANNEXMSCOPE | .1.3.6.1.4.1.2011.6.31.1.13.1.22 |
| hwadsl2L2ModeStateCfg The state of L2 power management mode.
Options:
1. disabled(1) - The L2 power management mode is disabled
2. enabled(2) - The L2 power management mode is enabled
3. forced(3) -… | column | Enumeration | .1.3.6.1.4.1.2011.6.31.1.13.1.23 |
| hwadsl2L2ModeMinDataRateCfg Minimum data rate in L2 mode.
Range: 128-16384
Default: 256
Unit: Kbps | column | Kbps Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.24 |
| hwadsl2L2ModeMaxDataRateCfg Maximum data rate in L2 mode.
Range: 128-16384
Default: 1024
Unit: Kbps | column | Kbps Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.25 |
| hwadsl2L2ModePayloadRateThresholdCfg Threshold for the Payload Rate Ratio.
Range: 128-16384
Default: 128
Unit: Kbps | column | Kbps Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.26 |
| hwadsl2L2ModeGuardTimeCfg Guard time before entering L2 mode.
Range: 0-1024
Default: 60
Unit: seconds | column | seconds Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.27 |
| hwadsl2L2ModeIntervalTimeCfg The minimum interval between two records of L2 mode.
Range: 0-255
Default: 255
Unit: seconds | column | seconds Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.28 |
| hwadsl2L2ModeIntervalPowerValueCfg Maximum aggregate transmit power reduction per L2 request or L2 power trim.
Range: 0-31
Default: 3
Unit: db | column | db Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.29 |
| hwadslLineDisableToneSection1EndCfg The end index of the first section.
Range: 0-511 | column | Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.3 |
| hwadsl2L2ModeTotalPowerValueCfg Total maximum aggregate transmit power reduction in L2.
Range: 0-31
Default: 9
Unit: db | column | db Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.30 |
| hwadslExtUsPhyRcontrolCfg To enable or disable the PHY-R function on upstream direction.
Options:
1. enable(1) - The PHY-R function on upstream direction is enabled
2. disable(2) - The PHY-R function on u… | column | Enumeration | .1.3.6.1.4.1.2011.6.31.1.13.1.31 |
| hwadslExtUsINPmaxCfg Maximum Impulse Noise Protection on upstream direction.
The parameter can take the following values:
noProtection(1),
halfSymbol(2),
singleSymbol(3),
twoSymbols(4),
threeSymbols(5… | column | DMT Symbol ADSL2-LINE-TC-MIBAdsl2SymbolProtection | .1.3.6.1.4.1.2011.6.31.1.13.1.32 |
| hwadslExtUsMinRtxRatioCfg Minimum rtx ratio on upstream direction.
Range: 0-255
Default: 0
Unit: 1/256 | column | 1/256 Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.33 |
| hwadslExtUsMinRSoverheadCfg The minimum value of R/N on upstream direction.
Range: 0-128
Default: 0
Unit: 1/256 | column | 1/256 Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.34 |
| hwadslExtDsPhyRcontrolCfg To enable or disable the PHY-R function on downstream direction.
Options:
1. enable(1) - The PHY-R function on downstream direction is enabled
2. disable(2) - The PHY-R function … | column | Enumeration | .1.3.6.1.4.1.2011.6.31.1.13.1.35 |
| hwadslExtDsINPmaxCfg Maximum Impulse Noise Protection on downstream direction.
The parameter can take the following values:
noProtection(1),
halfSymbol(2),
singleSymbol(3),
twoSymbols(4),
threeSymbols… | column | DMT Symbol ADSL2-LINE-TC-MIBAdsl2SymbolProtection | .1.3.6.1.4.1.2011.6.31.1.13.1.36 |
| hwadslExtDsMinRtxRatioCfg Minimum rtx ratio on downstream direction.
Range: 0-255
Default: 0
Unit: 1/256 | column | 1/256 Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.37 |
| hwadslExtDsMinRSoverheadCfg The minimum value of R/N on downstream direction.
Range: 0-128
Default: 0
Unit: 1/256 | column | 1/256 Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.38 |
| hwadsl2TSSiPsdMaskUsCfg The upstream PSD mask applicable at the U-C2 reference
point.
This parameter is used only for G992.3 or G992.5 and it may impose PSD
restrictions (breakpoints) in addition to the … | column | ADSL2-LINE-TC-MIBAdsl2PsdMaskUs | .1.3.6.1.4.1.2011.6.31.1.13.1.39 |
| hwadslLineDisableToneSection1FlagCfg The enable flag of the first section.
Options:
1. enabled(1) - The first tone section is enabled
2. disabled(2) - The first tone section is disabled | column | Enumeration | .1.3.6.1.4.1.2011.6.31.1.13.1.4 |
| hwadslLConfProfAdslModeCfg The ADSL2 management model specified includes an ADSL Mode
attribute which identifies an instance of ADSL Mode-Specific
PSD Configuration object in the ADSL Line Profile. The
foll… | column | Enumeration | .1.3.6.1.4.1.2011.6.31.1.13.1.40 |
| hwadslLineExtConfProfileRowStatusCfg This object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to
'active'. When 'active' is set, the system… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.2011.6.31.1.13.1.41 |
| hwadsl2L2ModeL2TimeCfg This minimum time (in seconds) between an entry into the
L2 state and the first power trim in the L2 state and between
two consecutive power trims in the L2 State.
It ranges from … | column | seconds Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.42 |
| hwadslLineExtConfProfRtxModeDs The mode of operation of G.998.4 retransmission in downstream direction.
Options:
1. forbidden(0) - G.998.4 retransmission not a… | column | Enumeration | .1.3.6.1.4.1.2011.6.31.1.13.1.43 |
| hwadslLineExtConfProfLeftrThreshDs If retransmission is used in downstream direction, this parameter specifies the
threshold for declaring a near-end leftr defect. The value is coded as a fraction of the
NDR with… | column | 0.01 Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.44 |
| hwadslLineExtConfProfMinEtrRtxDs If retransmission is used in downstream direction, this parameter specifies the
minimum expected throughput for the bearer channel.The values range in steps of
1000 bit/s. | column | bits/second Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.45 |
| hwadslLineExtConfProfMaxEtrRtxDs If retransmission is used in downstream direction, this parameter specifies the
maxmum expected throughput for the bearer channel.The values range in steps of
1000 bit/s. | column | bits/second Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.46 |
| hwadslLineExtConfProfMaxNdrRtxDs If retransmission is used in downstream direction, this parameter specifies the
maximum net data rate for the bearer channel. The values range in steps of 1000 bit/s. | column | bits/second Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.47 |
| hwadslLineExtConfProfMaxDelayRtxDs If retransmission is used in downstream direction, this parameter specifies
the maximum for the instantaneous delay due to the effect of retransmission only
(see G.998.4 for det… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.48 |
| hwadslLineExtConfProfMinDelayRtxDs If retransmission is used in downstream direction, this parameter specifies
the minimum for the instantaneous delay due to the effect of retransmission only
(see G.998.4 for det… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.49 |
| hwadslLineDisableToneSection2BeginCfg The begin index of the second section.
Range: 0-511 | column | Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.5 |
| hwadslLineExtConfProfMinInpShineRtxDs If retransmission is used in downstream direction, this parameter specifies
the minimum impulse noise protection against SHINE for the bearer channel if it is
transported over D… | column | symbols Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.50 |
| hwadslLineExtConfProfShineRatioRtxDs If retransmission is used in downstream direction, this parameter specifies
the SHINE ratio (detailed definition see G.998.4).
The values range from 0 to 0.100 in increments of 0… | column | Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.51 |
| hwadslLineExtConfProfMinInpReinRtxDs If retransmission is used in downstream direction, this parameter specifies
the minimum impulse noise protection against REIN for the bearer channel if it is
transported over DM… | column | Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.52 |
| hwadslLineExtConfProfIatReinRtxDs If retransmission is used in downstream direction, this parameter specifies
the inter-arrival time that shall be assumed for REIN protection.
Options:
1. frequency100Hz(0) - an… | column | Enumeration | .1.3.6.1.4.1.2011.6.31.1.13.1.53 |
| hwadsl2LExtLineProfReferenceClock This object configures the clock reference for the ATU-C
in an ADSL line. Represented as an enumeration.
Options:
1. freeRun(1) - Indicates the local clock
2. system(2) - Indicat… | column | Enumeration | .1.3.6.1.4.1.2011.6.31.1.13.1.54 |
| hwadsl2LExtLineProfRfiBands The RFI notch parameter.
It is a string consist of begin tone index,
end tone index.
This is a string of 4 groups of values in the following
structure:
Octets 0+1 - Index of st… | column | OctetString | .1.3.6.1.4.1.2011.6.31.1.13.1.55 |
| hwadsl2LExtLineProfDpboEPsd This parameter defines the PSD mask that is assumed to be permitted at the exchange.
This parameter shall use the same format as PSDMASKds.The maximum number of breakpoints
for … | column | OctetString | .1.3.6.1.4.1.2011.6.31.1.13.1.56 |
| hwadsl2LExtLineProfDpboEsEL This configuration parameter defines the assumed electrical length of
cables (E-side cables) connecting exchange based DSL services to a remote
flexibility point (cabinet), that … | column | 0.5dB Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.57 |
| hwadsl2LExtLineProfDpboEselMin DPBOESELMIN in dB is the minimum of all main cable losses for the KVz supplied when using
the SOL model (expansion of a KVz and ADSL2 provision of additional KVz areas from this K… | column | 0.5dB Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.58 |
| hwadsl2LExtLineProfDpboEsCableModelA This configuration parameter defines a cable model in terms of three scalars
DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency
dependent loss of E-s… | column | Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.59 |
| hwadslLineDisableToneSection2EndCfg The end index of the second section.
Range: 0-511 | column | Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.6 |
| hwadsl2LExtLineProfDpboEsCableModelB This configuration parameter defines a cable model in terms of three scalars
DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency
dependent loss of E-s… | column | Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.60 |
| hwadsl2LExtLineProfDpboEsCableModelC This configuration parameter defines a cable model in terms of three scalars
DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency
dependent loss of E-s… | column | Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.61 |
| hwadsl2LExtLineProfDpboMus DPBOMUS defines the assumed minimum usable receive signal PSD (in dBm/Hz) for
exchange based services, used to modify parameter DPBOFMAX defined below. It
shall be coded as an u… | column | 0.5dBm/Hz Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.62 |
| hwadsl2LExtLineProfDpboFMin DPBOFMIN defines the minimum frequency from which the DPBO shall be applied.
It shall be coded as a 16 bits unsigned integer representing a frequency in
multiple of 4.3125 KHz. … | column | 4.3125 KHz Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.63 |
| hwadsl2LExtLineProfDpboFMax DPBOFMAX defines the maximum frequency at which DPBO may be applied. It shall be
coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz.
The range… | column | 4.3125 KHz Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.64 |
| hwadsl2LExtLineProfMaxNomPsdUs Maximum PSD margin in upstream. | column | dBm/Hz Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.65 |
| hwadsl2LExtLineProfMaxNomAtpDs The maximum nominal aggregate transmit power in the
downstream direction during initialization and showtime. It
ranges from 0 to 255 units of 0.1 dBm (physical values are 0
to 25.… | column | 0.1 dBm Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.66 |
| hwadsl2LExtLineProfMaxNomAtpUs The maximum nominal aggregate transmit power in the upstream
direction during initialization and showtime. It ranges from
0 to 255 units of 0.1 dBm (physical values are 0 to 25.5
… | column | 0.1 dBm Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.67 |
| hwadsl2LExtLineProfInmIatoDs The parameter of downstream impulse noise monitoring inter arrival time offset.
This is the inter arrival time offset that the xTU receiver shall use to determine
in which bin of… | column | Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.68 |
| hwadsl2LExtLineProfInmIatsDs The parameter of downstream impulse noise monitoring inter arrival time step.
This is the inter arrival time step that the xTU receiver shall use to determine
in which bin of the… | column | Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.69 |
| hwadslLineDisableToneSection2FlagCfg The enable flag of the second section.
Options:
1. enabled(1) - The second tone section is enabled
2. disabled(2) - The second tone section is disabled | column | Enumeration | .1.3.6.1.4.1.2011.6.31.1.13.1.7 |
| hwadsl2LExtLineProfInmCcDs The parameter of downstream impulse noise monitoring cluster continuation value.
This is the cluster continuation value that the xTU receiver shall use
in the cluster indication … | column | Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.70 |
| hwadsl2LExtLineProfInmInpeqModeDs The parameter of downstream impulse noise monitoring equivalent impulse noise protect mode.
This is the INM Equivalent INP Mode that the xTU receiver shall use in the computation … | column | Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.71 |
| hwadsl2LExtLineProfForceInpDs The parameter indicates that the framer settings of the upstream bearer
shall be selected such that the impulse noise protection computed according
to the formula specified in t… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.6.31.1.13.1.72 |
| hwadsl2LExtLineProfForceInpUs The parameter indicates that the framer settings of the upstream bearer
shall be selected such that the impulse noise protection computed according
to the formula specified in t… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.6.31.1.13.1.73 |
| hwadsl2LExtLineProfInitPolicy If retransmission is not used in a given transmit direction, this parameter indicates
which policy shall be applied to determine the transceiver configuration parameters at
initi… | column | Enumeration | .1.3.6.1.4.1.2011.6.31.1.13.1.74 |
| hwadsl2LExtLineProfL3Time This minimum time (in seconds) between an entry into the
L3 state and the L0 or L2 state. | column | seconds Unsigned32 | .1.3.6.1.4.1.2011.6.31.1.13.1.75 |
| hwadsl2LExtLineProfL3ModeState Power management state enabling. The state of L3 power management mode.
Options:
1. enabled(1) - The L3 power management mode is enabled
2. disabled(2) - The L3 power management … | column | Enumeration | .1.3.6.1.4.1.2011.6.31.1.13.1.76 |
| hwadslLineDisableToneSection3BeginCfg The begin index of the third section.
Range: 0-511 | column | Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.8 |
| hwadslLineDisableToneSection3EndCfg The end index of the third section.
Range: 0-511 | column | Integer32 | .1.3.6.1.4.1.2011.6.31.1.13.1.9 |