hh3cIfPfcStatus

Object

column r/w Enumeration

Pfc (Priority-based Flow Control) status.
Forcibly enable Pfc by enable(1).
Disable Pfc by disable(2).
Set Pfc to auto mode by auto(3).
      In auto mode, the local end automatically negotiates
      the Pfc status with its peer.
When congestion occurs in the network, the local device notifies
the peer to stop sending packets carrying the specified 802.1p
priority if all of the following conditions exist:
1. Both the local end and the remote end have Pfc enabled.
2. Both the local end and the remote end have the dot1p list specified
by hh3cIfPfcDot1pNoDrop.
3. The specified 802.1p priority is in the dot1p list of hh3cIfPfcDot1pNoDrop.
4. The local end receives a packet carrying the specified 802.1p priority.

Context

MIB: HH3C-IF-EXT-MIB
OID: .1.3.6.1.4.1.25506.2.40.2.3.2.1.11
Type: column
Access: readwrite
Status: current
Parent: hh3cIfEntry
Table: hh3cIfTable
Siblings: 15

Related Objects

Sibling Objects

Object	Type	Syntax	OID
hh3cIfUpDownTimes The interface's up/down times, since the device was initialized.	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.25506.2.40.2.3.2.1.1`
hh3cIfDownTimes Number of times the interface went down, since the device was initialized.	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.25506.2.40.2.3.2.1.10`
hh3cIfPfcDot1pNoDrop Pfc (Priority-based Flow Control) dot1q list, bit 0 through bit 7 corresponding to priority 0 through priority 7. See hh3cIfPfcStatus.	column	Bits	`.1.3.6.1.4.1.25506.2.40.2.3.2.1.12`
hh3cIfDescription This object is also an 'alias' name for the interface specified by a network manager, like the object of ifAlias. However, the size of this object is larger than ifAlias. When t…	column	OctetString	`.1.3.6.1.4.1.25506.2.40.2.3.2.1.13`
hh3cIfFwdErrDiscards The number of packets that were discarded when being forwarded.	column	SNMPv2-SMIUnsigned32	`.1.3.6.1.4.1.25506.2.40.2.3.2.1.14`
hh3cIfFiberOrCopper Type of the port,which can be copper or fiber.	column	Enumeration	`.1.3.6.1.4.1.25506.2.40.2.3.2.1.15`
hh3cIfTransferMode Transfer mode of the port, which can be lan or wan.	column	Enumeration	`.1.3.6.1.4.1.25506.2.40.2.3.2.1.16`
hh3cIfMtu The size of the largest datagram that can be sent or received on the interface, specified in octets. For interfaces that are used for transmitting network datagram, this is the s…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.25506.2.40.2.3.2.1.2`
hh3cIfBandwidthRate The rate of the bandwidth for an interface.	column	Integer32	`.1.3.6.1.4.1.25506.2.40.2.3.2.1.3`
hh3cIfDiscardPktRate The rate of the discarded packets for an interface.	column	Integer32	`.1.3.6.1.4.1.25506.2.40.2.3.2.1.4`
hh3cIfStatusKeepTime The time since the interface entered its current operational state.	column	RFC1155-SMITimeTicks	`.1.3.6.1.4.1.25506.2.40.2.3.2.1.5`
hh3cIfInNUcastPkts The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol.	column	SNMPv2-SMICounter64	`.1.3.6.1.4.1.25506.2.40.2.3.2.1.6`
hh3cIfOutNUcastPkts The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address.	column	SNMPv2-SMICounter64	`.1.3.6.1.4.1.25506.2.40.2.3.2.1.7`
hh3cIfIsPoe Whether the interface supports PoE.	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.25506.2.40.2.3.2.1.8`
hh3cIfOperStatus Current status of the interface. In testing state, no operational packets can be forwarded. If ifAdminStatus is down, hh3cIfOperStatus should be admindown. If ifAdminStatus is …	column	Enumeration	`.1.3.6.1.4.1.25506.2.40.2.3.2.1.9`

Indexes

`1`	enable
`2`	disable
`3`	auto

Object

Context

Syntax

Values & Constraints

Related Objects