upsConfigOutputFreqsecond
GEPARALLELUPS-MIB ·
.1.3.6.1.4.1.818.1.1.12.9.4
Object
scalar
r/w
0.1 Hertz NonNegativeInteger32
The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
Context
- MIB
- GEPARALLELUPS-MIB
- OID
.1.3.6.1.4.1.818.1.1.12.9.4- Type
- scalar
- Access
- readwrite
- Status
- current
- Units
- 0.1 Hertz
- Parent
- upsConfigsecond
- Siblings
- 13
Syntax
0.1 Hertz NonNegativeInteger32
- Source
- NonNegativeInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: 0..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| upsConfigInputVoltagesecond The magnitude of the nominal input voltage. On those
systems which support read-write access to this
object, if there is an attempt to set this variable to
a value that is not su… | scalar | RMS Volts NonNegativeInteger32 | .1.3.6.1.4.1.818.1.1.12.9.1 |
| upsConfigHighVoltageTransferPointsecond The maximum line voltage allowed before the UPS
system transfers to battery backup.(*) | scalar | RMS Volts NonNegativeInteger32 | .1.3.6.1.4.1.818.1.1.12.9.10 |
| upsConfigBatteryCapacitysecond The installed battery capacity. This value is the 'factory'-value,
not the value after calibration. | scalar | Amps Hours NonNegativeInteger32 | .1.3.6.1.4.1.818.1.1.12.9.11 |
| upsConfigBatteryChargeCurrentsecond The maximum battery charge current, including external chargers. | scalar | 0.1 Amp DC NonNegativeInteger32 | .1.3.6.1.4.1.818.1.1.12.9.12 |
| upsConfigNoLoadShutdownsecond Dis- or enable 'no load' shutdown from the contact interface. | scalar | Enumeration | .1.3.6.1.4.1.818.1.1.12.9.13 |
| upsConfigStartDelaysecond Minimum required autonomy time before the UPS may perform an
autorestart. | scalar | minutes PositiveInteger32 | .1.3.6.1.4.1.818.1.1.12.9.14 |
| upsConfigInputFreqsecond The nominal input frequency. On those systems which
support read-write access to this object, if there is
an attempt to set this variable to a value that is not
supported, the re… | scalar | 0.1 Hertz NonNegativeInteger32 | .1.3.6.1.4.1.818.1.1.12.9.2 |
| upsConfigOutputVoltagesecond The magnitude of the nominal output voltage. On
those systems which support read-write access to this
object, if there is an attempt to set this variable to
a value that is not s… | scalar | RMS Volts NonNegativeInteger32 | .1.3.6.1.4.1.818.1.1.12.9.3 |
| upsConfigOutputVAsecond The magnitude of the nominal Volt-Amp rating.(*) | scalar | Volt-Amps NonNegativeInteger32 | .1.3.6.1.4.1.818.1.1.12.9.5 |
| upsConfigOutputPowersecond The magnitude of the nominal true power rating.(*) | scalar | Watts NonNegativeInteger32 | .1.3.6.1.4.1.818.1.1.12.9.6 |
| upsConfigLowBattTimesecond The value of upsEstimatedMinutesRemaining at which a
lowBattery condition is declared. For agents which
support only discrete (discontinuous) values, then the
agent shall round u… | scalar | minutes NonNegativeInteger32 | .1.3.6.1.4.1.818.1.1.12.9.7 |
| upsConfigAudibleStatussecond The requested state of the audible alarm. When in
the disabled state, the audible alarm should never
sound. The enabled state is self-describing. Setting
this object to muted(3… | scalar | Enumeration | .1.3.6.1.4.1.818.1.1.12.9.8 |
| upsConfigLowVoltageTransferPointsecond The minimum input line voltage allowed before the UPS
system transfers to battery backup.(*) | scalar | RMS Volts NonNegativeInteger32 | .1.3.6.1.4.1.818.1.1.12.9.9 |
Notification Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| upsShutdownAfterDelay Setting this object will shutdown (i.e., turn off)
either the UPS output or the UPS system (as determined
by the value of upsShutdownType at the time of
shutdown) after the indica… | scalar | seconds Integer32 | .1.3.6.1.4.1.818.1.1.10.8.2 |