upsConfigInputVoltage

GEPARALLELUPS-MIB · .1.3.6.1.4.1.818.1.1.10.9.1

MIB view Table view

Object

scalar r/w RMS Volts NonNegativeInteger32

The magnitude of the nominal input voltage.  On those
systems which support read-write access to this
object, if there is an attempt to set this variable to
a value that is not supported, the request must be
rejected and the agent shall respond with an
appropriate error message, i.e., badValue for SNMPv1,
or inconsistentValue for SNMPv2.(*)

Context

MIB: GEPARALLELUPS-MIB
OID: .1.3.6.1.4.1.818.1.1.10.9.1
Type: scalar
Access: readwrite
Status: current
Units: RMS Volts
Parent: upsConfig
Siblings: 13

Syntax

RMS Volts NonNegativeInteger32

Source: NonNegativeInteger32
Base type: Integer32

Values & Constraints

Type Constraints

range: 0..2147483647

Related Objects

Sibling Objects

Object	Type	Syntax	OID
upsConfigHighVoltageTransferPoint The maximum line voltage allowed before the UPS system transfers to battery backup.(*)	scalar	RMS Volts NonNegativeInteger32	`.1.3.6.1.4.1.818.1.1.10.9.10`
upsConfigBatteryCapacity The installed battery capacity. This value is the 'factory'-value, not the value after calibration.	scalar	Amps Hours NonNegativeInteger32	`.1.3.6.1.4.1.818.1.1.10.9.11`
upsConfigBatteryChargeCurrent The maximum battery charge current, including external chargers.	scalar	0.1 Amp DC NonNegativeInteger32	`.1.3.6.1.4.1.818.1.1.10.9.12`
upsConfigNoLoadShutdown Dis- or enable 'no load' shutdown from the contact interface.	scalar	Enumeration	`.1.3.6.1.4.1.818.1.1.10.9.13`
upsConfigStartDelay Minimum required autonomy time before the UPS may perform an autorestart.	scalar	minutes PositiveInteger32	`.1.3.6.1.4.1.818.1.1.10.9.14`
upsConfigInputFreq The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the re…	scalar	0.1 Hertz NonNegativeInteger32	`.1.3.6.1.4.1.818.1.1.10.9.2`
upsConfigOutputVoltage The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not s…	scalar	RMS Volts NonNegativeInteger32	`.1.3.6.1.4.1.818.1.1.10.9.3`
upsConfigOutputFreq The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the r…	scalar	0.1 Hertz NonNegativeInteger32	`.1.3.6.1.4.1.818.1.1.10.9.4`
upsConfigOutputVA The magnitude of the nominal Volt-Amp rating.(*)	scalar	Volt-Amps NonNegativeInteger32	`.1.3.6.1.4.1.818.1.1.10.9.5`
upsConfigOutputPower The magnitude of the nominal true power rating.(*)	scalar	Watts NonNegativeInteger32	`.1.3.6.1.4.1.818.1.1.10.9.6`
upsConfigLowBattTime The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round u…	scalar	minutes NonNegativeInteger32	`.1.3.6.1.4.1.818.1.1.10.9.7`
upsConfigAudibleStatus The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3…	scalar	Enumeration	`.1.3.6.1.4.1.818.1.1.10.9.8`
upsConfigLowVoltageTransferPoint The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)	scalar	RMS Volts NonNegativeInteger32	`.1.3.6.1.4.1.818.1.1.10.9.9`

Indexes