upsConfigAudibleStatusfourth

GEPARALLELUPS-MIB · .1.3.6.1.4.1.818.1.1.14.9.8
MIB view Table view

Object

scalar r/w Enumeration 
The requested state of the audible alarm.  When in
the disabled state, the audible alarm should never
sound.  The enabled state is self-describing.  Setting
this object to muted(3) when the audible alarm is
sounding shall temporarily silence the alarm.  It will
remain muted until it would normally stop sounding and
the value returned for read operations during this
period shall equal muted(3).  At the end of this
period, the value shall revert to enabled(2).  Writes
of the value muted(3) when the audible alarm is not
sounding shall be accepted but otherwise shall have no
effect.(*)

Context

MIB
GEPARALLELUPS-MIB
OID
.1.3.6.1.4.1.818.1.1.14.9.8
Type
scalar
Access
readwrite
Status
current
Parent
upsConfigfourth
Siblings
13

Syntax

Enumeration

Values & Constraints

No enumerated values or constraints recorded.

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
upsConfigInputVoltagefourth
The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not su…
scalarRMS Volts NonNegativeInteger32.1.3.6.1.4.1.818.1.1.14.9.1
upsConfigHighVoltageTransferPointfourth
The maximum line voltage allowed before the UPS system transfers to battery backup.(*)
scalarRMS Volts NonNegativeInteger32.1.3.6.1.4.1.818.1.1.14.9.10
upsConfigBatteryCapacityfourth
The installed battery capacity. This value is the 'factory'-value, not the value after calibration.
scalarAmps Hours NonNegativeInteger32.1.3.6.1.4.1.818.1.1.14.9.11
upsConfigBatteryChargeCurrentfourth
The maximum battery charge current, including external chargers.
scalar0.1 Amp DC NonNegativeInteger32.1.3.6.1.4.1.818.1.1.14.9.12
upsConfigNoLoadShutdownfourth
Dis- or enable 'no load' shutdown from the contact interface.
scalarEnumeration.1.3.6.1.4.1.818.1.1.14.9.13
upsConfigStartDelayfourth
Minimum required autonomy time before the UPS may perform an autorestart.
scalarminutes PositiveInteger32.1.3.6.1.4.1.818.1.1.14.9.14
upsConfigInputFreqfourth
The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the re…
scalar0.1 Hertz NonNegativeInteger32.1.3.6.1.4.1.818.1.1.14.9.2
upsConfigOutputVoltagefourth
The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not s…
scalarRMS Volts NonNegativeInteger32.1.3.6.1.4.1.818.1.1.14.9.3
upsConfigOutputFreqfourth
The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the r…
scalar0.1 Hertz NonNegativeInteger32.1.3.6.1.4.1.818.1.1.14.9.4
upsConfigOutputVAfourth
The magnitude of the nominal Volt-Amp rating.(*)
scalarVolt-Amps NonNegativeInteger32.1.3.6.1.4.1.818.1.1.14.9.5
upsConfigOutputPowerfourth
The magnitude of the nominal true power rating.(*)
scalarWatts NonNegativeInteger32.1.3.6.1.4.1.818.1.1.14.9.6
upsConfigLowBattTimefourth
The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round u…
scalarminutes NonNegativeInteger32.1.3.6.1.4.1.818.1.1.14.9.7
upsConfigLowVoltageTransferPointfourth
The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)
scalarRMS Volts NonNegativeInteger32.1.3.6.1.4.1.818.1.1.14.9.9
Notification Objects
ObjectTypeSyntaxOID
upsSecondsOnBatterythird
If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is…
scalarSeconds SNMPv2-SMIInteger32.1.3.6.1.4.1.818.1.1.13.2.2