snSwIfInfoMonitorMode
FOUNDRY-SN-SWITCH-GROUP-MIB ·
.1.3.6.1.4.1.1991.1.1.3.3.5.1.2
Object
column
deprecated
r/w
Enumeration
DEPRECATED by snSwIf2MirrorMode and snPortMonitorTable.
Context
- MIB
- FOUNDRY-SN-SWITCH-GROUP-MIB
- OID
.1.3.6.1.4.1.1991.1.1.3.3.5.1.2- Type
- column
- Access
- readwrite
- Status
- deprecated
- Parent
- snSwIfInfoEntry
- Table
- snSwIfInfoTable
- Siblings
- 68
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | disabled |
1 | input |
2 | output |
3 | both |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| snSwIfInfoPortNum The port/interface index (ifindex). | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.1991.1.1.3.3.5.1.1 |
| snSwIfInfoAdminStatus The desired state of all ports. The
testing(3) state indicates that no operational
packets can be passed.
(same as ifAdminStatus in MIB-II) | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.10 |
| snSwIfInfoLinkStatus The current operational state of the interface.
The testing(3) state indicates that no operational
packets can be passed.
(same as ifOperStatus in MIB-II) | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.11 |
| snSwIfInfoPortQos The Stand alone stackable switch Port Qos Priority values are:
low(0) -- low prority
high(1) -- high prority.
The BigIron Port Qos Priority values are:
level0(0), level1(1), lev… | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.12 |
| snSwIfInfoPhysAddress The port physical address. The physical address
represents the switch port. | column | PhysAddress | .1.3.6.1.4.1.1991.1.1.3.3.5.1.13 |
| snSwIfLockAddressCount The number of source MAC addresses are allowed
for a port. Writing 0 to this object will allow
any number of addresses. | column | Integer32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.14 |
| snSwIfStpPortEnable The enabled/disabled status of the port. | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.15 |
| snSwIfDhcpGateListId The ID for a DHCP gateway list entry relative
to this switch port. 0 = unset or no assigned ID | column | Integer32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.16 |
| snSwIfName Port Name string. | column | OctetString | .1.3.6.1.4.1.1991.1.1.3.3.5.1.17 |
| snSwIfDescr A textual string containing the slot/port information
about the interface. | column | FOUNDRY-SN-AGENT-MIBDisplayString | .1.3.6.1.4.1.1991.1.1.3.3.5.1.18 |
| snSwIfInfoAutoNegotiate This feature only applies to Gigabit Ethernet ports. If set to
disable(0), port will be put to non-negotiation mode. If set to
enable(1), port will start auto-negotiation indefini… | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.19 |
| snSwIfInfoFlowControl Enable/Disbale port flow control. | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.20 |
| snSwIfInfoGigType The media type for the port. The
values are:
m1000BaseSX(0)....1Gbits per second fiber, with a short wavelength transceiver.
m1000BaseLX(1)....1Gbits per second fiber, with a … | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.21 |
| snSwIfFastSpanPortEnable The enabled/disabled fast span port status of the port. | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.22 |
| snSwIfFastSpanUplinkEnable The enabled/disabled fast span uplink status of the port. | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.23 |
| snSwIfVlanId deprecated This object return 0 due to no support for this object from FI 08.0.80 release.
Write operation not-supported for this object. | column | Integer32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.24 |
| snSwIfRouteOnly Enable/Disable L2 switching of a routing switch port.
By default, the routing switch performs routing first.
If routing failed, it performs switching. Enable route
only instrcuts … | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.25 |
| snSwIfPresent Indicate if the port is absent or present.
This object only valid for M4 module. | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.26 |
| snSwIfGBICStatus Indicate if the gig port has GBICs on them.
If set to GBIC(1), it means that the port is GBIC.
If set to miniGBIC(2), it means that the port miniGBIC.
If set to empty(3), it mea… | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.27 |
| snSwIfLoadInterval The time in seconds for which average port utilization should be carried out.
The value should be incremental of 30 seconds, between the ranges specified. | column | Integer32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.28 |
| snSwIfStatsInFrames The total number of packets received on the interface. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.29 |
| snSwIfInfoMirrorPorts The list of port/interface index (ifindex), which mirror this interface,
when monitoring is enabled. | column | OctetString | .1.3.6.1.4.1.1991.1.1.3.3.5.1.3 |
| snSwIfStatsOutFrames The total number of packets transmitted out of the interface. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.30 |
| snSwIfStatsAlignErrors dot3StatsAlignmentErrors : A count of frames
received on a particular interface that are
not an integral number of octets in length
and do not pass the FCS check.
… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.31 |
| snSwIfStatsFCSErrors dot3StatsFCSErrors : A count of frames received
on a particular interface that are an integral
number of octets in length but do not pass the
FCS check.
The coun… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.32 |
| snSwIfStatsMultiColliFrames dot3StatsMultipleCollisionFrames :
A count of successfully transmitted frames on
a particular interface for which transmission
is inhibited by more than one collision.
… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.33 |
| snSwIfStatsTxColliFrames A count of successfully transmitted frames on
a particular interface for which transmission
is inhibited by more than one collision.
A frame that is counted by a co… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.34 |
| snSwIfStatsRxColliFrames A count of successfully received frames on
a particular interface for which transmission
is inhibited by more than one collision. This
object is not specified in dot3 but it has … | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.35 |
| snSwIfStatsFrameTooLongs dot3StatsFrameTooLongs : A count of frames
received on a particular interface that
exceed the maximum permitted frame size.
The count represented by an instance o… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.36 |
| snSwIfStatsFrameTooShorts A count of frames received on a particular
interface that below the minimum permitted
frame size. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.37 |
| snSwIfStatsInBcastFrames The total number of broadcast packets received on the interface. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.38 |
| snSwIfStatsOutBcastFrames The total number of broadcast packets transmitted out of the interface. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.39 |
| snSwIfInfoTagMode Configure an interface as tagged member of non-default VLAN,
untagged VLAN membership of the interface will not be modified,
be it is default-VLAN or non-default VLAN. Configure… | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.4 |
| snSwIfStatsInMcastFrames The total number of multicast packets received on the interface. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.40 |
| snSwIfStatsOutMcastFrames The total number of multicast packets transmitted out of the interface. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.41 |
| snSwIfStatsInDiscard The number of inbound packets which were chosen
to be discarded even though no errors had been
detected to prevent their being deliverable to a
higher-layer protocol. One possibl… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.42 |
| snSwIfStatsOutDiscard The number of outbound packets which were chosen
to be discarded even though no errors had been
detected to prevent their being transmitted. One
possible reason for discarding su… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.43 |
| snSwIfStatsMacStations The total number of MAC Stations connected to the interface. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.44 |
| snSwIfStatsLinkChange The total number of link state change of the interface. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.45 |
| snSwIfInOctets The total number of octets received on the interface,
including framing characters. This object is a 64-bit
counter of the ifInOctets object, defined in RFC 1213.
The octet string… | column | SNMPv2-SMICounter64 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.46 |
| snSwIfOutOctets The total number of octets transmitted out of the interface,
including framing characters. This object is a 64-bit
counter of the ifOutOctets object, defined in RFC 1213.
The octe… | column | SNMPv2-SMICounter64 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.47 |
| snSwIfStatsInBitsPerSec The number of bits per second received on the interface
over a 5 minutes interval. | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.48 |
| snSwIfStatsOutBitsPerSec The number of bits per second transmitted out of the interface
over a 5 minutes interval. | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.49 |
| snSwIfInfoTagType The IEEE802.1q tag type embedded in the length/type field of
an Ethernet packet. It specifies that the 2 octets after the
length/type field in an Ethernet packet is the tag value. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.5 |
| snSwIfStatsInPktsPerSec The number of packets per second received on the interface
over a 5 minutes interval. | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.50 |
| snSwIfStatsOutPktsPerSec The number of packets per second transmitted out of the interface
over a 5 minutes interval. | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.51 |
| snSwIfStatsInUtilization The input network utilization in hundredths of a percent
over a 5 minutes interval. | column | Integer32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.52 |
| snSwIfStatsOutUtilization The output network utilization in hundredths of a percent
over a 5 minutes interval. | column | Integer32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.53 |
| snSwIfStatsInKiloBitsPerSec Bit rate in kilobits per second received on the 10G and
faster interface over a 5 minutes interval. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.54 |
| snSwIfStatsOutKiloBitsPerSec Bit rate in kilobits per second transmitted out of the 10G
and faster interface over a 5 minutes interval. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.55 |
| snSwIfStatsInJumboFrames The total number of jumbo packets received on the interface. | column | SNMPv2-SMICounter64 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.56 |
| snSwIfStatsOutJumboFrames The total number of jumbo packets transmitted out of the interface. | column | SNMPv2-SMICounter64 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.57 |
| snSwIfInfoMirrorMode Enable/disable mirror on this port. | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.58 |
| snSwIfMacLearningDisable The status of MAC learning feature on an ethernet port.
For POS port, Get operation will return the default value and Set operation will return an error. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1991.1.1.3.3.5.1.59 |
| snSwIfInfoChnMode The port can be configured to operate in either
half or full duplex mode. The values are:
halfDuplex(1)...half duplex mode
fullDuplex(2)...full duplex mode
The read-back channel… | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.6 |
| snSwIfInfoNativeMacAddress The port native MAC address. The native MAC address
represents the switch port. | column | PhysAddress | .1.3.6.1.4.1.1991.1.1.3.3.5.1.62 |
| snSwIfQosMonitorDropCounterMode Enable/disable monitoring egress drop counter on this port.
ICX7150 has a set of queue drop counters. A port can be selected to associate with these counters.
Only when the port i… | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.63 |
| snSwIfLRMAdapterPresent To display the state for Long Reach Module (LRM) adapter is presented on this port.
Some FastIron ICX devices support LRM optics on 10G fiber ports.
LRM adapter (Fluffy) is used … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1991.1.1.3.3.5.1.64 |
| snSwIfStpBPDUGuardMode The status of the spanning tree BPDU guard on an ethernet port.
The default is false state. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1991.1.1.3.3.5.1.65 |
| snSwIfStpRootGuardMode The status of the spanning tree root guard on an ethernet port.
Declare the port to be on root guard for all spanning trees.
The default is false state. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1991.1.1.3.3.5.1.66 |
| snSwIfRstpAdminEdgePortMode The status of the rapid spanning tree admin edge port on an ethernet port.
Declare the port to be an operational edge for all vlans.
The default is false state. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1991.1.1.3.3.5.1.67 |
| snSwIfInfoClockMode The port can be configured to operate in either
master or slave mode. The values are:
none(0).........no configured or no support for clock mode, like fiber ports.
master(1).… | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.68 |
| snSwIfProtectedMode Protected port is a port-level, per-device/stack only, security feature that restricts communication with a device connected to the port.
The default is false state. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1991.1.1.3.3.5.1.69 |
| snSwIfInfoSpeed The speed configuration for a port. The values are:
none(0)..........link down or no traffic.
sAutoSense(1)....Auto-sensing 10 or 100Mbits.
s10M(2)..........10Mbits per second.
s1… | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.7 |
| snSwIfTrustDscpMode The status of Trust DSCP on an ethernet port.
The default is false state. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1991.1.1.3.3.5.1.70 |
| snSwIfVoiceVlanId VLAN can be configurated as a voice over IP VLAN on an ethernet port.
The valid range of voice VLAN ID is 1-4095.
The value 0 means that the voice VLAN is not configurated or is … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.1991.1.1.3.3.5.1.71 |
| snSwIfInfoMediaType The media type for the port. The
values are:
other(1).........other or unknown media.
m100BaseTX(2)....100Mbits per second copper.
m100BaseFX(3)....100Mbits per second fiber… | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.8 |
| snSwIfInfoConnectorType The type of connector that the port offers.
The values are:
other(1)...........other or unknown connector
copper(2)..........Copper connector
fiber(3)...........Fiber connector… | column | Enumeration | .1.3.6.1.4.1.1991.1.1.3.3.5.1.9 |