ltmDiametersessionProfileMaxWatchdogFailures
F5-BIGIP-LOCAL-MIB ·
.1.3.6.1.4.1.3375.2.2.6.39.1.2.1.7
Object
column
RFC1155-SMIGauge
Specifies the maximum number of device watchdog failures that the traffic management system can take before it tears down the connection. After the system receives this number of device watchdog failures, it closes the connection if the reset-on-timeout is enabled. However, if the reset-on-timeout is not enabled, but the watchdog timeout count is great and equal than 3 times of max-watchdog-failures, then the connection is closed.
Context
- MIB
- F5-BIGIP-LOCAL-MIB
- OID
.1.3.6.1.4.1.3375.2.2.6.39.1.2.1.7- Type
- column
- Access
- readonly
- Status
- current
- Parent
- ltmDiametersessionProfileEntry
- Table
- ltmDiametersessionProfileTable
- Siblings
- 49
Syntax
RFC1155-SMIGauge
- Source
- RFC1155-SMIGauge
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ltmDiametersessionProfileName The Name of the diametersession profile. | column | F5-BIGIP-COMMON-MIBLongDisplayString | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.1 |
| ltmDiametersessionProfileRetransmissionAction Specifies the action to be
performed when retransmission is triggered for a request message.
disable: retransmission is disabled busy: A busy answer is sent to
the originator of t… | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.10 |
| ltmDiametersessionProfileArrayRetransmissionErrorCode Specifies a list of
DIAMETER error codes that if an answer message is received
containing one of the listed error codes, the corresponding
request will be retransmitted as directe… | column | F5-BIGIP-COMMON-MIBLongDisplayString | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.11 |
| ltmDiametersessionProfileRetransmissionQueueMaxMessages Specifies the
maximum number of messages that may be held in the retransmission
message queue. If a request message is received that is enabled
for retransmission and the retransm… | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.12 |
| ltmDiametersessionProfileRetransmissionQueueMaxBytes Specifies the maximum
number of bytes that may be held in the retransmission message
queue. If a request message is received that is enabled for
retransmission and the retransmiss… | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.13 |
| ltmDiametersessionProfileRetransmissionQueueLimitHigh Specifies the high
watermark for the retransmission queue in percent. If the number
of messages or bytes in the retransmission queue for a connection
exceeds the high watermark, t… | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.14 |
| ltmDiametersessionProfileRetransmissionQueueLimitLow Specifies the low
watermark for the retransmission queue in percent. If the number
of messages or bytes in the retransmission queue for a connection
drops below the low watermark,… | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.15 |
| ltmDiametersessionProfileDiscardUnroutable If enabled,
discard unroutable messages. | column | Enumeration | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.16 |
| ltmDiametersessionProfileLoopDetection If enabled, detect and
reject (error response) looped request messages. | column | Enumeration | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.17 |
| ltmDiametersessionProfileWatchdogTimeout Specifies the watchdog timeout in
seconds. This setting specifies the number of seconds that a
connection is idle before the device watchdog request is sent. The
default value is … | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.18 |
| ltmDiametersessionProfileMaxMessageSize Maximum bytes that will be allowed
for the messages. The default value is 0, which means no such
restriction is allowed in BIG-IP. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.19 |
| ltmDiametersessionProfileConfigSource The state that specifies whether this is a base/pre-configured profile
or user defined profile. | column | Enumeration | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.2 |
| ltmDiametersessionProfilePersistType Specifies the type of the persistence.
None - Persistence is disabled
AVP - To persist based on avp in the message.
Custom - To persist based on the custom key specified using iRu… | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.20 |
| ltmDiametersessionProfilePersistAvp Specifies the Diameter AVP that is used
for persistence. The format is avp[index] for a single AVP or
a[x]:b[y]:c[z]:d[w] for a grouped AVP. There may be at most 4 AVPs
in a group… | column | F5-BIGIP-COMMON-MIBLongDisplayString | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.21 |
| ltmDiametersessionProfilePersistTimeout Indicates the timeout value for
persistence entries in seconds. Its recommended to have the
persist-timeout to be greater than transaction timeout, specified
in the Diameter route… | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.22 |
| ltmDiametersessionProfileOriginHostRewrite Rewrites the Origin-Host AVP to
the specified value on the egress. | column | F5-BIGIP-COMMON-MIBLongDisplayString | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.23 |
| ltmDiametersessionProfileOriginRealmRewrite Rewrites the Origin-Host AVP to
the specified value on the egress. | column | F5-BIGIP-COMMON-MIBLongDisplayString | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.24 |
| ltmDiametersessionProfileDestHostRewrite Rewrites the Destination-Host AVP
to the specified value on the egress. | column | F5-BIGIP-COMMON-MIBLongDisplayString | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.25 |
| ltmDiametersessionProfileDestRealmRewrite Rewrites the Destination-Realm AVP
to the specified value on the egress. | column | F5-BIGIP-COMMON-MIBLongDisplayString | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.26 |
| ltmDiametersessionProfileOriginHost Specifies the identifier of the
originating server in the form siteserver.f5.com. Must specify the
origin-host. | column | F5-BIGIP-COMMON-MIBLongDisplayString | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.27 |
| ltmDiametersessionProfileOriginRealm Origin-Realm AVP data. Must specify the
origin-realm. | column | F5-BIGIP-COMMON-MIBLongDisplayString | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.28 |
| ltmDiametersessionProfileHostIpAddress Specifies the IP address of the
diameter server. If no value is specified, the system uses the
BIG-IP system's IP address on the VLAN that the system uses to
generate traffic to t… | column | F5-BIGIP-COMMON-MIBLongDisplayString | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.29 |
| ltmDiametersessionProfileDefaultName The name of the profile from which the specified profile derives
its attribute default values. | column | F5-BIGIP-COMMON-MIBLongDisplayString | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.3 |
| ltmDiametersessionProfileVendorId Specifies the vendor identification number
assigned to your diameter server by the Internet Assigned Numbers
Authority (IANA). The default is 0. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.30 |
| ltmDiametersessionProfileFirmwareRevision Specifies the firmware revision of
the issuing device to inform a diameter peer. The default value
is 1. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.31 |
| ltmDiametersessionProfileProductName Specifies the vendor-assigned name for
the product. | column | F5-BIGIP-COMMON-MIBLongDisplayString | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.32 |
| ltmDiametersessionProfileAuthApplicationId Specifies the Authentication and
Authorization identifier for a specific application, as specified
in RFC 6733. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.33 |
| ltmDiametersessionProfileAcctApplicationId Specifies the Accounting
identifier for a specific application, as specified in RFC
6733. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.34 |
| ltmDiametersessionProfileArrayAuthApplicationId Specifies a space separted
list of Authentication and Authorization identifiers for a
specific application, as specified in RFC 6733. | column | F5-BIGIP-COMMON-MIBLongDisplayString | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.35 |
| ltmDiametersessionProfileArrayAcctApplicationId Specifies a space separated
list of Accounting identifiers for a specific application, as
specified in RFC 6733. | column | F5-BIGIP-COMMON-MIBLongDisplayString | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.36 |
| ltmDiametersessionProfileVendorSpecificVendorId Specifies the vendor
identification number for the vendor-specific application. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.37 |
| ltmDiametersessionProfileVendorSpecificAuthApplicationId Specifies the
authentication identification number for the vendor-specific
application. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.38 |
| ltmDiametersessionProfileVendorSpecificAcctApplicationId Specifies the
accounting identification number for the vendor-specific
application. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.39 |
| ltmDiametersessionProfileRouteUnconfiguredPeers When it is
enabled, unconfigured peers is added to the route table. | column | Enumeration | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.4 |
| ltmDiametersessionProfilePeerDelayCriticalLimit Specifies the critical limit
threshold for peer delay. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.40 |
| ltmDiametersessionProfileEgressCriticalMessageRateLimit Specifies the
critical message rate limit threshold for messages sent to peer. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.41 |
| ltmDiametersessionProfileEgressMajorMessageRateLimit Specifies the
major message rate limit threshold for messages sent to peer. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.42 |
| ltmDiametersessionProfileIngressCriticalMessageRateLimit Specifies the
critical message rate limit threshold for messages received from peer. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.43 |
| ltmDiametersessionProfileIngressMajorMessageRateLimit Specifies the
major message rate limit threshold for messages received peer. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.44 |
| ltmDiametersessionProfileDynamicRouteInsertion If enabled,
dynamically add routes for connected peers. | column | Enumeration | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.45 |
| ltmDiametersessionProfileDynamicRouteLookup If enabled,
route messages based on dynamically added routes. | column | Enumeration | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.46 |
| ltmDiametersessionProfileDynamicRouteTimeout Specifies the duration after
which dynamic routes will be removed after the releated peer
connections are closed. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.47 |
| ltmDiametersessionProfilePeerErrorsMajorThreshold Specifies the major limit
threshold for peer errors. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.48 |
| ltmDiametersessionProfilePeerTimeoutsMajorThreshold Specifies the major limit
threshold for peer timeouts. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.49 |
| ltmDiametersessionProfileHandshakeTimeout Indicates the number of seconds
before the handshake times out to a peer. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.5 |
| ltmDiametersessionProfileDisconnectPeerAction Specifies the type of action
taken when Disconnect Peer Request received from peer.
None: Terminates connection on receiving DPR.Connection can be re-established between peer… | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.50 |
| ltmDiametersessionProfileMaxRetransmissions Number of times, the peer tries to
retransmit the message. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.6 |
| ltmDiametersessionProfileResetOnTimeout When it is enabled
and the watchdog failures exceed the max watchdog failure, the
system resets the connection. The default value is enabled. | column | Enumeration | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.8 |
| ltmDiametersessionProfileRetransmissionTimeout Specifies the retransmission
timeout in seconds. This setting specifies the number of seconds
the BIG-IP waits to retransmit the request messages if it does not
receive the corres… | column | RFC1155-SMIGauge | .1.3.6.1.4.1.3375.2.2.6.39.1.2.1.9 |