mTotalActiveEnergy

ES-RACKTIVITY-MIB · .1.3.6.1.4.1.34097.9.77.1.1.20
MIB view Table view

Object

column kWh Uthousandth 
Gets the total energy of a power module. (unit: 0.001kWh)

Context

MIB
ES-RACKTIVITY-MIB
OID
.1.3.6.1.4.1.34097.9.77.1.1.20
Type
column
Access
readonly
Status
current
Units
kWh
Parent
eMasterEntry
Table
eMasterTable
Siblings
125

Syntax

kWh Uthousandth
Source
Uthousandth
Base type
Unsigned32

Values & Constraints

No enumerated values or constraints recorded.

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
mGeneralModuleStatus
General status of a module.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.1
mStatus
status of a module
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.1000
mModuleName
Gets, sets or defaults the module name.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10001
mFirmwareVersion
Gets the version of the module's firmware.
columnVersion.1.3.6.1.4.1.34097.9.77.1.1.10002
mHardwareVersion
Gets the version of a module's hardware.
columnVersion.1.3.6.1.4.1.34097.9.77.1.1.10003
mFirmwareID
Gets the ID of the module's firmware.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10004
mHardwareID
Gets the ID of a module's hardware.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10005
mRackName
Gets, sets or defaults the name of the rack.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10006
mRackPosition
Gets, sets or defaults the position in the rack.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10007
mIPAddress
Gets, sets or defaults the IP address (when DHCP is disabled).
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.34097.9.77.1.1.10011
mSubNetMask
Gets, sets or defaults the subnet mask (when DHCP is disabled).
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.34097.9.77.1.1.10012
mStdGateWay
Gets, sets or defaults the standard gateway (when DHCP is disabled).
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.34097.9.77.1.1.10013
mDnsServer
Gets, sets or defaults the IP address of the used DNS server (when DHCP is disabled).
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.34097.9.77.1.1.10014
mMAC
Gets the MAC address of a master module.
columnSNMPv2-TCMacAddress.1.3.6.1.4.1.34097.9.77.1.1.10015
mDHCPEnable
Enables, disables or defaults DHCP. Set to 1 to enable DHCP, or 0 to disable DHCP.
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10016
mNTPServer
Gets, sets or defaults the NTP (Network Time Protocol) server IP address.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.34097.9.77.1.1.10017
mUseDefaultNTPServer
Enables, disables or defaults the usage of the default NTP (Network Time Protocol) server (pool.ntp.org).
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10018
mUseNTP
Enables, disables or defaults NTP (Network Time Protocol). Set to 1 to enable NTP, or 0 to disable NTP.
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10019
mSNMPTrapRecvIP
Gets, sets or defaults the SNMP trap receiver IP address.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.34097.9.77.1.1.10020
mSNMPTrapRecvPort
Gets, sets or defaults the SNMP tap receiver port.
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10021
mSNMPControl
Enables, disables or defaults write access over SNMP. Set to 1 to disable write access, or 0 to enable write access.
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10024
mECSServer
Gets, sets or defaults the ECS (Energy Cloud Sentinel) server IP address.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.34097.9.77.1.1.10028
mUseECSServer
Enables, disables or defaults the use of an ECS (Energy Cloud Sentinel) server. Set to 1 to enable or 0 to disable.
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10029
mDisplayLock
Gets, sets or defaults the display lock. If the display is locked, you can still view information on the display, but you are not allowed to change settings through the menu syste…
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10031
mDisplayTimeOn
Gets, sets or defaults the display sleep timer. If the display is inactive for longer than this time, the display turns off to save power. Time is in minutes. (unit: min)
columnmin Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.10032
mMaxVoltageWarning
Gets, sets or defaults the maximum voltage warning level. (unit: 0.01V)
columnV Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.10047
mMinVoltageWarning
Gets, sets or defaults the minimum voltage warning level. (unit: 0.01V)
columnV Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.10049
mMinTemperatureWarning
Gets, sets or defaults the minimum temperature warning level (use DEF accessor to reset). (unit: 0.1K)
columnK Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.10052
mMaxTemperatureWarning
Gets, sets or defaults the maximum temperature warning level (use DEF accessor to reset). (unit: 0.1K)
columnK Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.10053
mGeneralEventEnable
Gets, sets or defaults general events. If set to 0, no events will be generated. Set to 1 to generate events on media indicated by the event bitfields.
columnEVENTFLAGS.1.3.6.1.4.1.34097.9.77.1.1.10074
mSNMPSysContact
Gets, sets or defaults the SNMP contact information.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10075
mCurrentWarningEvent
Enables or disables the SNMP trap if the outlet current warning level is exceeded.
columnEVENTFLAGS.1.3.6.1.4.1.34097.9.77.1.1.10078
mPowerWarningEvent
Enables or disables the SNMP trap if the power warning level is exceeded.
columnEVENTFLAGS.1.3.6.1.4.1.34097.9.77.1.1.10080
mTotalCurrentWarningEvent
Enables or disables the SNMP trap if the total outlet current warning level is exceeded.
columnEVENTFLAGS.1.3.6.1.4.1.34097.9.77.1.1.10082
mTotalPowerWarningEvent
Enables or disables the SNMP trap if the total power warning level is exceeded.
columnEVENTFLAGS.1.3.6.1.4.1.34097.9.77.1.1.10084
mVoltageWarningEvent
Enables or disables the SNMP trap if the voltage warning level is exceeded.
columnEVENTFLAGS.1.3.6.1.4.1.34097.9.77.1.1.10086
mTemperatureWarningEvent
Enables or disables the SNMP trap if the temperature warning level is exceeded.
columnEVENTFLAGS.1.3.6.1.4.1.34097.9.77.1.1.10087
mDisplayBrightness
Gets, sets or defaults the display brightness (if supported).
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10098
mECSServerPort
Gets, sets or defaults the ECS (Energy Cloud Sentinel) server port.
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10106
mExternalSensorLabel
Gets, sets or defaults the external sensor label. External sensors can be connected to Energy Sensors.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10109
mHttpsOnly
Enables or disables the use of HTTPS (secure HTTP). Set to 1 to enable HTTPS only, or 0 to also enable HTTP.
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10127
mTelnetSsl
Enables or disables the use of Telnet SSL (secure Telnet). Set to 1 to enable Telnet SSL, or 0 to disable Telnet SSL).
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10128
mCookieTimeToLive
The TTL (Time To Live) of the website cookie. (unit: min)
columnmin Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.10130
mLineCurrentWarningThreshold
Gets, sets the warning threshold of the linecurrent. (unit: 0.001A)
columnA Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.10131
mLineCurrentOffThreshold
Gets, sets the off threshold of the linecurrent. (unit: 0.001A)
columnA Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.10132
mLineCurrentWarningEvent
Enables or disables the SNMP trap if the linecurrent warning level is exceeded.
columnEVENTFLAGS.1.3.6.1.4.1.34097.9.77.1.1.10133
mLineCurrentOffEvent
Enables or disables the SNMP trap if the linecurrent off level is exceeded.
columnEVENTFLAGS.1.3.6.1.4.1.34097.9.77.1.1.10134
mFuseCurrentWarningThreshold
Gets, sets or defaults the maximum current warning threshold per fuse. (unit: 0.001A)
columnA Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.10142
mFuseCurrentOffThreshold
Gets, sets or defaults the maximum current off threshold per fuse. (unit: 0.001A)
columnA Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.10143
mFuseCurrentWarningEvent
Enables or disables the SNMP trap if the fusecurrent warning threshold is exceeded.
columnEVENTFLAGS.1.3.6.1.4.1.34097.9.77.1.1.10144
mFuseCurrentOffEvent
Enables or disables the SNMP trap if the fusecurrent off threshold is exceeded.
columnEVENTFLAGS.1.3.6.1.4.1.34097.9.77.1.1.10145
mDeviceID
The ID of the device.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10150
mDeviceVersion
The version of the device.
columnVersion.1.3.6.1.4.1.34097.9.77.1.1.10151
mSysName
The full name of the device.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10152
mElectricalTopology
Gets the electrical topology of the unit.
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10153
mFusePortTopology
Gets the topology between the outlets and fuses.
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10154
mLineFuseTopology
Gets the topology between the inlet (cable or connection) and the fuses.
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10155
mSSOIPAddress
Gets, sets the IP address of an SSO (Smart Style Office).
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.34097.9.77.1.1.10156
mSSOLoginCredentials
Gets, sets the login credentials of an SSO (Smart Style Office).
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10157
mSSOGracefullShutdown
Gets, sets the string to send if the UPS' battery level is below the set threshold.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10158
mUPSWarningLevel
Gets, sets or defaults the graceful shutdown threshold of a UPS.
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10159
mUPSOffLevel
Gets, sets or defaults the threshold of a UPS to set outlets off.
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10160
mMaxHighCurrentWarning
Gets sets or defaults the maximum high current warning level. (unit: 0.1A)
columnA Integer32.1.3.6.1.4.1.34097.9.77.1.1.10165
mUpsMonitoringProtocol
Disables/Enables UPS monitoring and selects the protocol used for UPS monitoring. 0 = Disabled; 1 = Use old APC protocol
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10167
mUpsEmergencyThreshold
When the UPS battery level goes below this threshold a shutdown request will be sent to all agents (unit: 0.1%)
column% Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.10168
mUpsRecoveryThreshold
When the UPS battery level goes above this threshold a outlets will be powered on as configured by the user (unit: 0.1%)
column% Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.10169
mUpsEventFlags
Event flags for events related to the UPS monitoring
columnEVENTFLAGS.1.3.6.1.4.1.34097.9.77.1.1.10170
mRecoveryPowerThreshold
When the UPS was on battery and it went below UPSEMERGTHRES, the outlets that have a load below the RECOVPOWERTHRES will be power cycled once the UPS is back on mains power and ex…
columnW Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.10171
mMinHighCurrentWarning
Gets sets or defaults the minimum high current warning level. (unit: 0.1A)
columnA Integer32.1.3.6.1.4.1.34097.9.77.1.1.10176
mMinHighPowerWarning
Gets sets or defaults the power min high current warning level. (unit: 0.01kW)
columnkW Integer32.1.3.6.1.4.1.34097.9.77.1.1.10177
mMaxHighPowerWarning
Gets sets or defaults the power max high current warning level. (unit: 0.01kW)
columnkW Integer32.1.3.6.1.4.1.34097.9.77.1.1.10178
mHeartbeatInterval
Interval (in seconds) between 2 heartbeat SNMP traps, Set to 0 to disable (unit: s)
columns Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.10179
mMinTotalHighCurrentWarning
Gets sets or defaults the maximum high current warning level. (unit: 0.1A)
columnA Integer32.1.3.6.1.4.1.34097.9.77.1.1.10180
mMaxTotalHighCurrentWarning
Gets sets or defaults the maximum high current warning level. (unit: 0.1A)
columnA Integer32.1.3.6.1.4.1.34097.9.77.1.1.10181
mMinTotalHighPowerWarning
Gets sets or defaults the power min high current warning level. (unit: 0.01kW)
columnkW Integer32.1.3.6.1.4.1.34097.9.77.1.1.10182
mMaxTotalHighPowerWarning
Gets sets or defaults the power max high current warning level. (unit: 0.01kW)
columnkW Integer32.1.3.6.1.4.1.34097.9.77.1.1.10183
mCloudState
Set if the device needs to push info to the init cloud (val=0) or to the normal cloud (val=1)
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10208
mSensorBias
get or set the DC sensor bias (unit: mV)
columnmV Integer32.1.3.6.1.4.1.34097.9.77.1.1.10210
mDaisyChainDeviceMode
allowed modes: 0: standalone (master without daisy chain slaves) 1: daisy chain master 2: daisy chain slave 1 3: daisy chain slave 2 4: daisy chain slave 3
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10211
mSNMPTrapUser
Gets, sets or defaults the SNMP tap user out of the user list.
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10212
mUSMUser
Gets, sets or defaults the SNMP USM security user
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10213
mUSMAuthPassphrase
Gets, sets or defaults the SNMP USM authentication passphrase (Always MD5)
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10214
mUSMPrivPassphrase
Gets, sets or defaults the SNMP USM private passphrase (Always AES)
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10215
mSNMPV2GetSetEnable
Gets, sets or defaults the SNMP V2 Enable for get ,set or walk but not for traps.
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10216
mSNMPV3GetSetEnable
Gets, sets or defaults the SNMP V3 Enable for get ,set or walk but not for traps.
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10217
mUSMAuthPassphraseLength
Gets, sets or defaults the SNMP USM authentication passphrase length
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10218
mUSMPrivPassphraseLength
Gets, sets or defaults the SNMP USM private passphrase length
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10219
mSNMPTrapEnable
Gets, sets or defaults the SNMP Trap Enable per trap account
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10222
mLDAPAttribute
Attribute linked to the LDAPFilter
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10227
mLDAPPath
Relative Path to be used for the LDAPFilter
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10228
mLDAPAdminGroupName
GroupName for Admin Credentials in LDAP
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10229
mLDAPRestrictedGroupName
GroupName for Restricted Credentials in LDAP
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10230
mLDAPGuestGroupName
GroupName for Guest Credentials in LDAP
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10231
mLDAPEnable
Enable or disable login via LDAP credentials
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10232
mLDAPLoginWrapper
Wrapper for login in with LDAP
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10233
mLDAPServer
NO_INFO
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.77.1.1.10235
mLocalAuthEnable
Set if local authentication is still possible if LDAP is enabled
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.10236
mTemperature
Gets the current temperature of a temperature sensor. (unit: 0.1K)
columnK Utenth.1.3.6.1.4.1.34097.9.77.1.1.11
mCurrentIP
Gets the current IP address. To set the IP address, use IPADDR instead.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.34097.9.77.1.1.14
mTotalCurrent
Gets the total current of a power module. (unit: 0.001A)
columnA Uthousandth.1.3.6.1.4.1.34097.9.77.1.1.17
mTotalRealPower
Gets the total power level of a power module. (unit: W)
columnW SNMPv2-SMIUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.18
mSpecificModuleStatus
Specific status of a module.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.2
mCurrentTime
Gets or sets the current time (not possible when NTP is enabled). (unit: UNIX)
columnUNIX SNMPv2-SMITimeTicks.1.3.6.1.4.1.34097.9.77.1.1.3
mLineCurrent
Gets the current line current. (unit: 0.001A)
columnA Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.32
mFuseCurrent
Gets the current through a fuse. (unit: 0.001A)
columnA Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.33
mCurrentSubNetMask
Gets the current subnet mask. To set the subnet mask use SNMSK instead.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.34097.9.77.1.1.34
mCurrentDNSServer
Gets the current DNS server. To set the DNS server use DNSSRV instead.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.34097.9.77.1.1.35
mCurrentStdGateway
Gets the current standard gateway. To set the standard gateway use STDGW instead.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.34097.9.77.1.1.36
mUPSPresent
Checks if a UPS is present.
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.37
mUPSStatus
Gets the working status of a UPS (if its working on its batteries or not).
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.38
mUPSEstimatedRunTime
Gets the estimated run time of a UPS. (unit: min)
columnmin Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.39
mVoltage
Gets the voltage of a power module. (unit: 0.01V)
columnV Uhundredth.1.3.6.1.4.1.34097.9.77.1.1.4
mUPSBatteryLevel
The current UPS battery level. (unit: 0.1%)
column% Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.40
mHighCurrent
The current for high values (unit: 0.1A)
columnA Stenth.1.3.6.1.4.1.34097.9.77.1.1.41
mUpsCommunicationStatus
Status information of communication with the UPS
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.42
mHighPower
The power for high values (unit: 0.01kW)
columnkW Integer32.1.3.6.1.4.1.34097.9.77.1.1.43
mTotalHighCurrent
The current for high values (unit: 0.1A)
columnA Integer32.1.3.6.1.4.1.34097.9.77.1.1.44
mTotalHighPower
The power for high values (unit: 0.01kW)
columnkW Integer32.1.3.6.1.4.1.34097.9.77.1.1.45
mPositiveEnergy
Gets the positive energy used by an outlet. (unit: 0.001kWh)
columnkWh Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.46
mNegativeEnergy
Gets the negative energy used by an outlet. (unit: 0.001kWh)
columnkWh Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.47
mTotalPositiveEnergy
Gets the positive energy of the module. (unit: 0.001kWh)
columnkWh Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.48
mTotalNegativeEnergy
Gets the negative energy of the module. (unit: 0.001kWh)
columnkWh Unsigned32.1.3.6.1.4.1.34097.9.77.1.1.49
mCloudStatus
Gets the status of the connection with the cloud. 0 = Idle state; 1 = Disabled; 2 = Initialising; 3 = Initialising - No connection; 4 = Initialising - No key; 5 = Connection Ok; 6…
columnUnsigned32.1.3.6.1.4.1.34097.9.77.1.1.56
masterIndex
Index for the selected Master Module
columnInteger32.1.3.6.1.4.1.34097.9.77.1.1.65537
masterModuleIndex
Selected Master Module
columnInteger32.1.3.6.1.4.1.34097.9.77.1.1.65538