enetTestType
ELECTROLINE-DHT-ENET-MIB ·
.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.8
Object
column
r/w
Enumeration
Sets the type of test to be ran. Selection is made between the following two: voip(1): A VoIP simulation RTP test will be ran, sender will transmit packets simulating a voice codec and the VoIP metrics will be computer by the receiver. packetLoss(2): In a Packet Loss test the sender simply sends a specified packet rate (enetTestPacketRate) and the receiver counts the number of packets received.
Context
- MIB
- ELECTROLINE-DHT-ENET-MIB
- OID
.1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.8- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- enetTestControlEntry
- Table
- enetTestControlTable
- Siblings
- 18
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | voip |
2 | packetLoss |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| enetTestIndex Index for this set of test controls. One set controls one instance
of the test engine. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.1 |
| enetTestPacketInterval Interval in milliseconds between each packets.
This parameter is used only for the RTP test type. | column | Integer32 | .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.10 |
| enetTestPacketRate Number of packets per seconds to be transmitted.
This parameter is used only for packetLoss test type. | column | Integer32 | .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.11 |
| enetTestNumOfPackets Maximum duration of the test expressed in number of packets.
A sender will stop the transmitting when it reaches this amount.
A receiver can use this parameter … | column | Unsigned32 | .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.12 |
| enetTestJitterBufferSize Jitter buffer size in millisecond to be implemented by the receiving
entity. This will impact the total delay and the discarded packet count.
The value set in this… | column | Integer32 | .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.13 |
| enetTestQosControl This parameter tells the DHT is a specific service flow must be used
for the test.
none(1): Means that the test will run in a best effort mode.
prees… | column | Enumeration | .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.14 |
| enetTestCodecType The Codec type to be used for the rtp test.
It is used by sender to set the appropriate value in the
rtp header. The receiver can use this parameter in the comput… | column | Enumeration | .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.15 |
| enetTestTosByte Type of Service Byte to be used in the transmitted packets.
This parameter is used only for the rtp test type. | column | Integer32 | .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.16 |
| enetTestRoundTripTimeEstimate The round trip time (in milliseconds) is used by the DHT in the computation of the CQE
R-Factor. It must be estimated by the management entity and supplied
to the DHT via the us… | column | Integer32 | .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.17 |
| enetTestStatus This MIB indicates the test status. A value of N/A(0) is returned
before the test is ran. A value of Running (1) is returned while the
test is in progress. A value of Completed… | column | Enumeration | .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.18 |
| enetTestStatusString This field is used by the device to further explain the Status of
the test. and its content is device specific. | column | OctetString | .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.19 |
| enetTestIdString This String can be used by the management entity as a unique test
identifier string. The Enet module will simply copy this string
in the result table. | column | OctetString | .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.2 |
| enetTestControl Used to control the test engine. Once the control parameter for the
test are set, the management entity must set this to setupTest(2) &
verify that the test control status retu… | column | Enumeration | .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.3 |
| enetTestSenderIP This is the address of the sender entity for the test stream.
To set this device as the transmitter for the test, set this MIB to
its IP address. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.4 |
| enetTestSenderUDPPort Port Number that the sender will use. | column | Unsigned32 | .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.5 |
| enetTestReceiverIP This is the address of the receiving entity for this test stream.
To set this device as the receiver for the test, set this MIB to
its IP address.
If both enetTestR… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.6 |
| enetTestReceiverUDPPort UDP port number to be used by the receiving entity.
In loopback mode the receiver Port number is also used as both the reception
and source port of the loopbacking … | column | Unsigned32 | .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.7 |
| enetTestPacketSize Size of the Ethernet packet (Including headers) to be used by this
test.
Note that the packet size for rtp test is computed from the packet
interval and the codec… | column | Integer32 | .1.3.6.1.4.1.5802.1.3.1.2.5.1.12.1.3.1.1.1.9 |