portShutdownReason
ECS2100-MIB ·
.1.3.6.1.4.1.259.10.1.43.1.2.1.1.20
Object
column
Bits
The reason of port shutdown. The value is 0 if no shutdown action is applied to this port.
Context
- MIB
- ECS2100-MIB
- OID
.1.3.6.1.4.1.259.10.1.43.1.2.1.1.20- Type
- column
- Access
- readonly
- Status
- current
- Parent
- portEntry
- Table
- portTable
- Siblings
- 15
Syntax
Bits
Values & Constraints
Enumerated Values
1 | notTestedYet |
2 | ok |
3 | open |
4 | short |
8 | impedanceMismatch |
9 | failed |
10 | notSupported |
11 | noCable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| portIndex The port and the trunk (including trunk members) interface of
the portTable. The interface identified by a particular value
of this index is the same interface as identified by th… | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.259.10.1.43.1.2.1.1.1 |
| portTrunkIndex The trunk to which this port belongs. A value of 0
means that this port does not belong to any trunk.
A value greater than zero means that this port
belongs to a trunk in the trun… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.259.10.1.43.1.2.1.1.10 |
| portComboForcedMode This determines the running mode of a combo port.
For a non-combo port, this variable has a value of none(1),
and setting this variable to none(1) has no effect.
For a combo port,… | column | Enumeration | .1.3.6.1.4.1.259.10.1.43.1.2.1.1.12 |
| portMasterSlaveModeCfg Configures the PHY mode when auto negotiation is disabled and
speed-duplex is 1000full for giga copper port. | column | Enumeration | .1.3.6.1.4.1.259.10.1.43.1.2.1.1.15 |
| portMacAddrLearningStatus Set this variable to enabled(1) to start to learn MAC
addresses. Set this variable to disabled(2) to stop to
learn MAC addresses. | column | P-BRIDGE-MIBEnabledStatus | .1.3.6.1.4.1.259.10.1.43.1.2.1.1.17 |
| portMacAddrLearningCount The current number of learned MAC addresses. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.259.10.1.43.1.2.1.1.18 |
| portUpTime The port up time (in hundredths of a second). | column | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.259.10.1.43.1.2.1.1.19 |
| portName The name of the port or trunk. This is the same as ifAlias
in the IF-MIB (RFC2863 or later). | column | OctetString | .1.3.6.1.4.1.259.10.1.43.1.2.1.1.2 |
| portType Indicates the port type of the configuration of the switch. | column | Enumeration | .1.3.6.1.4.1.259.10.1.43.1.2.1.1.3 |
| portSpeedDpxCfg Configures the speed and duplex mode for a port or trunk,
according to:
halfDuplex10(2) - 10Mbps and half duplex mode
fullDuplex10(3) - 10Mbps and full duplex mode
… | column | Enumeration | .1.3.6.1.4.1.259.10.1.43.1.2.1.1.4 |
| portFlowCtrlCfg (1) Flow control mechanism is enabled with tx and rx pause
mechansim.
If the port type is hundredBaseTX or thousandBaseSX:
When the port is operating in halfDuplex mode, the
port … | column | Enumeration | .1.3.6.1.4.1.259.10.1.43.1.2.1.1.5 |
| portCapabilities Port or trunk capabilities. | column | Bits | .1.3.6.1.4.1.259.10.1.43.1.2.1.1.6 |
| portAutonegotiation Whether auto-negotiation is enabled. | column | P-BRIDGE-MIBEnabledStatus | .1.3.6.1.4.1.259.10.1.43.1.2.1.1.7 |
| portSpeedDpxStatus The operating speed and duplex mode of the
switched port or trunk. If the entry represents a trunk,
the speed is that of its individual members unless
the member ports have been i… | column | Enumeration | .1.3.6.1.4.1.259.10.1.43.1.2.1.1.8 |
| portFlowCtrlStatus (2) BackPressure flow control mechanism is used.
(3) IEEE 802.3 flow control mechanism is used.
(4) Flow control mechanism is disabled.
If the entry represents a trunk and the mem… | column | Enumeration | .1.3.6.1.4.1.259.10.1.43.1.2.1.1.9 |