agentVpcDomainSystemMac

DNOS-VPC-MIB · .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.6
MIB view Table view

Object

column r/w SNMPv2-TCMacAddress 
To configure the MAC address for the VPC domain. This mac-address 
is used in the LACP PDUs and STP BPDUs 
that are sent out on VPC member ports. For the VPC domain to use 
the manually configured VPC MAC address, it should be manually 
configured on both the VPC peers and should be the same. If VPC 
is configured on only one of the VPC peers or is configured 
different on VPC peers, auto-generated MAC address is used. 
The specified MAC address should be a unicast MAC address in 
<aa:bb:cc:dd:ee:ff> format and should not be equal to the 
MAC address of either primary VPC or secondary VPC device.  
The manually configured VPC MAC address is used instead of 
auto-generated VPC MAC address only if the VPC feature is 
re-enabled after configuring the VPC MAC address.

Context

MIB
DNOS-VPC-MIB
OID
.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.6
Type
column
Access
readwrite
Status
current
Parent
agentVpcDomainConfigEntry
Table
agentVpcDomainConfigTable
Siblings
12

Syntax

SNMPv2-TCMacAddress
Source
SNMPv2-TCMacAddress
Base type
OctetString

Values & Constraints

Type Constraints
range: 6

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
agentVpcDomainIndex
VPC Domain ID.
columnUnsigned32.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.1
agentVpcDomainPeerIpAddr
To configure IP address of the peer VPC switch. This configuration is used by the dual control plane detection protocol (DCPDP) on the VPC switches. NOTE: In order …
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.10
agentVpcDomainSourceIpAddr
To configure Self IP address of the VPC switch that is used as the source IP by the dual control plane detection protocol (DCPDP) on the VPC switches. NOTE: In orde…
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.11
agentVpcDomainDcpdpUdpPort
To configure the UDP port on which the VPC switch listens to the DCPDP messages. Configurable range is 1 to 65535. Default value is 50000. NOTE: In order to set val…
columnUnsigned32.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.12
agentVpcDomainStatus
Status of VPC Domain.
columnSNMPv2-TCRowStatus.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.13
agentVpcDomainKeepalivePriority
To configure the priority of the VPC switch. This value is used for the VPC role election. Configurable range is 1 to 255. The default value is 100. Note: The VPC switch with lowe…
columnUnsigned32.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.2
agentVpcDomainKeepaliveTimeout
To configure the peer keepalive timeout value (in seconds). If an VPC switch does not receive keepalive messages from the peer for this timeout value, it takes the decision to tra…
columnUnsigned32.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.3
agentVpcDomainKeepaliveMode
To start/stop the keepalive state machine on the VPC device, if VPC is globally enabled. The following options are supported: enable - Enable keepalive disable - D…
columnEnumeration.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.4
agentVpcDomainPeerDetectionMode
To start/stop the dual control plane detection protocol (DCPDP) on the VPC switch. The following options are supported: enable - Enable the DCPDP on VPC switch dis…
columnEnumeration.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.5
agentVpcDomainSystemPriority
To configure the system priority for the VPC domain. This is used in the LACP PDUs sent out on VPC member ports. System-priority should be configured same on both the VPC peers.…
columnUnsigned32.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.7
agentVpcDomainPeerDetectionInterval
To configure the DCPDP transmission interval. NOTE: In order to set value for the object, need to set values for DCPDP transmission interval and reception timeout simultaneously.
columnUnsigned32.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.8
agentVpcDomainPeerDetectionTimeout
To configure the DCPDP reception timeout. NOTE: In order to set value for the object, need to set values for DCPDP transmission interval and reception timeout simultaneously.
columnUnsigned32.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.9